• Journal of the Korean Society of Safety
• /
• v.12 no.2
• /
• pp.17-21
• /
• 1997

The fatigue crack propagation rate has so far been measured by the effective stress intensity factor range Δ K/sub eff/. But no research has been done to study how much the crack opening ratio influences the expectation of the fatigue crack propagation. Therefore, this paper evaluates of the crack opening ratio on the fatigue crack propagation life by using the method of parameter sensitivity study. Summarizing the result ; ( 1 ) When the crack opening ratio U' is high, the effect of U' gets larger than any other except for the material factor m. But when U' is low, the effect is also diminished. Therefore, the selection of the lowest value possible is desirable in the evaluation of life. (2) When the value of the material factor m is high, the effect of crack opening ratio U' is increased, at the same time the effect of the other parameters also increased wholly. The effect of material factor m itself on life is high, but in case the material factor m is high, that the effect of each parameter on life get higher is unique. In designing, better attention to the material selection should be drawn. (3) In case the stress ratio R gets smaller, the effect of crack opening ratio U' is unchangeable. But the effect of R itself remarkably decreases, and the effect of material factor m somewhat decreases.

• Proceedings of the KIEE Conference
• /
• 1994.11a
• /
• pp.281-283
• /
• 1994

The impedance characteristics of planar ICP have been measured and compared with the theoretical results obtained by the field equation. The resistance of the total impedance had a maximum point and the inductance decreased monotonically as the electron density increased from $2.5{\times}10^{10}cm^{-3}$ to $7{\times}10^{11}cm^{-3}$ and the Pressure from 1mT to 50mT. The impedance characteristics were also dependent on the profile of the electron density. The effective collision frequency, ${\nu}_{eff}$ was $9.0{\times}10^6Hz$ at 5mT and $.5{\times}10^7Hz$ at 100mT. The effective collision frequency at 5mT was not so different from that at 100mT and it is doe to the reduction of the discharge channel cross-section at high pressure. The estimated effective collision frequency from the simulation data was of the same order as the measured one.

• Nuclear Engineering and Technology
• /
• v.50 no.5
• /
• pp.709-716
• /
• 2018

A criticality safety analysis was performed for the APR-1400 spent fuel pool region-II to ensure the safe storage of spent fuel, with credit taken for depletion and in-rack neutron absorbers (Metamic panels). PLUS7 fuel assembly was modeled using TRITON-NEWT of SCALE-6.1. The burnup-dependent cross-section library was generated under limiting core-operating conditions with 5%-w U-235 initial enrichment. MCNP5 was used to evaluate the neutron multiplication factor in an infinite array of rack cells with the axially nonuniformly burnt PLUS7 assemblies under normal, abnormal, and accident conditions; including all biases and uncertainties. The main purpose of this study is to investigate reactivity variations due to the critical depletion and reactor operation parameters. The approach, assumptions, and modeling methods were verified by analyzing the contents of the most important fissile and the associated reactivity effects. The Nuclear Regulatory Commission (NRC) guidance on k-eff being less than 1.0 for spent fuel pools filled with unborated water was the main criterion used in this study. It was found that assemblies with 49.0 GWd/MTU and 5.0 w/o U-235 initial enrichment loaded in Region-II satisfy this criterion. Moreover, it was found that the end effect resulted in a positive bias, thus ensuring its consideration.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.02a
• /
• pp.216-216
• /
• 2010

이종접합 태양전지의 투명전도막으로 사용되는 ITO는 박막 증착시 Ar과 O2의 공정 가스비증가에 따라 일함수가 증가한다고 보고되어지고 있다. 이러한 일함수의 증가는 ITO와 n a-si:H과의 계면에서 barrier height를 낮춤으로써 hole injection을 원활하게 만들어줌으로써 이종접합 태양전지의 효율 향상을 기대할 수 있게 해준다. RF sputtering system으로 증착된 ITO 증착시 순수 Ar만으로 증착된 ITO와 0.1에서 0.5% 까지 미세산소함량으로 증착된 ITO의 단일막 특성과 이를 이종접합 태양전지에 적용하였을 때의 특성을 분석하였다. ITO의 단일막 전기적 특성 분석을 위하여 Hall measurement를 이용하였고 광학적 특성 분석을 위해 UV-Vis를 이용하였다. 또한 광전자 분광장치를 이용하여 일함수 변화를 측정하였다. 그리고 산소 함량에 따른 ITO 박막의 특성 변화를 통해 이종접합 태양전지의 광특성을 비교하였다. 전기적인 특성의 경우 0.1%의 산소함량에서 가장 낮은 비저항을 얻었고 이동도의 경우 산소 함량에 따라 점차 증가하게 되었다. 반면 Carrier concentration은 점차 감소하였다. 투과도의 경우 산소함량을 통해 제작된 ITO가 Ar만으로 제작된 ITO보다 500 nm 파장대에서 1% 정도의 높은 투과율을 갖게 되었다. 그리고 ITO 공정시 Ar 만으로 증착한 경우 4.3 eV의 일함수를 보이고 공정중 산소가 첨가됨으로써 4.8 eV 으로 일함수가 증가하게 되었고 이종접합 태양전지를 제작하여 Voc, Jsc, Eff 등이 각각 15mV, 2mA/cm2, 1.5% 정도의 광특성 향상을 얻을 수 있었다.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.11 no.2
• /
• pp.243-252
• /
• 1987

The propagation and closure behavior of surface crack initiated at a sharply notched specimens were investigated in 5083-H113 aluminium alloy under constant amplitude of tension load by the unloading elastic compliance method. The crack shape (aspect ratio) was found to be approximately semicircular during the crack was being small and to be changed to semi-elliptical during it was being long. The propagation rate of a surface crack initiated from notch root decelerated with increasing crack length when the crack was small and then accelerated when it was large. The effect of stress ratio was large in lower .DELTA.K range, but the effective stress intensity factor range .DELTA.K$_{eff}$ was found to diminish the difference of the crack propagation rate. By considering the increase in crack closure stress with crack length and examining the microphotographs, plasticity-induced and roughness-induced crack closure mechanisms were predominant in the range of this study.y.

• 한국신재생에너지학회:학술대회논문집
• /
• 2006.06a
• /
• pp.183-186
• /
• 2006

Reduction of optical losses in crystalline silicon solar cells by surface modification is one of the most important issues of silicon photovoltaics. Porous Si layers on the front surface of textured Si substrates have been investigated with the aim of improving the optical losses of the solar cells, because an anti-reflection coating and a surface passivation can be obtained simultaneously in one process. We have demonstrated the feasibility of a very efficient porous Si AR layer, prepared by a simple, cost effective, electrochemical etching method. Silicon p-type CZ (100) oriented wafers were textured by anisotropic etching in sodium carbonate solution. Then, the porous Si layer were formed by electrochemical etching in HF solutions. After that, the properties of porous Si in terms of morphology, structure and reflectance are summarized. The surface morphology of porous Si layers were investigated using SEM. The formation of a porous Si layer about $0.1{\mu}m$ thick on the textured silicon wafer result in an effective reflectance coefficient $R_{eff}$ lower than 5% in the wavelength region from 400 to 1000nm. Such a surface modification allows improving the Si solar cell characteristics.

• Journal of the Korean Applied Science and Technology
• /
• v.25 no.2
• /
• pp.232-239
• /
• 2008

Separation of naphthalene from naphthalene and 2-methylnaphthalene mixture has been studied by layered melt and solution crystallization using ethylalcohol. Purity and yield of naphthalene depended mainly on the cooling rate: The effective distribution coefficient ($K_{eff}$) as the degree of impurity removal was observed to decrease with the decreasing in cooling rate. Purity of naphthalene can be enhanced to $5{\sim}7%$ by melt crystallization using 90% naphthalene and the purity of naphthalene can be obtained to be 99% up by solution crystallization.

• Journal of Magnetics
• /
• v.18 no.3
• /
• pp.235-239
• /
• 2013

The effect of Dy addition on the microstructure and magnetic properties of the sintered NdFeB magnets was investigated. The results of the microstructure analysis showed that Dy-free and Dy-doped samples are composed of $Nd_2Fe_{14}B$ (P42/mnm) and a trace of Nd-rich phase. Dy addition reduces significantly the pole density factor of (004), (006) and (008) crystal faces as estimated by the Horta formula. Accordingly, the coercivity of the Dy-doped sample increases from 2038 $kA{\cdot}m^{-1}$ up to 2288 $kA{\cdot}m^{-1}$. The $H_{cj}(T)/M_s(T)$ versus $H^{min}_N/M_s(T)$ (Kronm$\ddot{u}$ller-plot) behavior shows that the nucleation is the dominating mechanism for the magnetization reversal in these two kinds of magnets, and two microstructural parameters of ${\alpha}_k$ and $N_{eff}$ are obtained. The Kronm$\ddot{u}$ller-Plot gives evidence for an increase of the ${\alpha}_k$ responsible for an increase of the coercivity as the result of the increase of the magnetic field as the magnetic domain reversed.

• Journal of Oriental Neuropsychiatry
• /
• v.32 no.3
• /
• pp.261-273
• /
• 2021

The purpose of this study was to introduce effects of Chukyu pharmacopuncture and Brainspotting on knee pain, headaches, and acute stress disorder of a patient with a traffic accident. We treated a patient with Chukyu pharmacopuncture and Brainspotting. Numerical rating scale (NRS), Range of Motion (ROM), Hyperextension Position (HEP), Effusion (Eff), Patella Compression Test (PCT), Frontal Flexion Position (FFP), McMurray (MCM), Lateral Joint Line Tenderness (LJLT), Medial Joint Line Tenderness (MJLT), Anterior Drawer Test (ADT), Lachman Test, Varus/Valgus stress, Beck Anxiety Inventory (BAI), Patient Health Questionnaire-9 (PHQ-9), Pittsburgh Sleep Quality Index (PSQI), Core Seven Emotions Inventory Short Form (CSEI-S), Subjective units of disturbance scale (SUDs), and Heart rate variability (HRV) were used to evaluate the patient. After the patient was treated by Chukyu pharmacopuncture and Brainspotting, the patient showed improvement in NRS, physical examination, and psychological symptom assessment. These results indicate that Chukyu pharmacopuncture and Brainspotting are effective on knee pain, headache, and acute stress disorder after a traffic accident.

• Nuclear Engineering and Technology
• /
• v.51 no.3
• /
• pp.818-824
• /
• 2019

In the present work, we determined the gamma-ray attenuation characteristics of eight different polymers(Polyamide (Nylon 6) (PA-6), polyacrylonitrile (PAN), polyvinylidenechloride (PVDC), polyaniline (PANI), polyethyleneterephthalate (PET), polyphenylenesulfide (PPS), polypyrrole (PPy) and polytetrafluoroethylene (PTFE)) using transmission geometry utilizing the high resolution HPGe detector and different radioactive sources in the energy range 81-1333 keV. The experimental linear attenuation coefficient values are compared with theoretical data (WinXCOM data). The linear attenuation coefficient of all polymers reduced quickly with the increase in energy, at the beginning, while decrease more slowly in the region from 267 keV to 835 keV. The effective atomic number of PVDC and PTFE are comparatively higher than the $Z_{eff}$ of the remaining polymers, while PA-6 possesses the lowest effective atomic number. The half value layer results showed that PTFE ($C_2F_4$, highest density) is more effective to attenuate the gamma photons. Also, the theoretical results of macroscopic effective removal cross section for fast neutrons ($\sum_{R}$) were computed to investigate the neutron attenuation characteristics. It is found that the $\sum_{R}$ values of the eight investigated polymers are close and ranged from $0.07058cm^{-1}$ for PVDC to $0.11510cm^{-1}$ for PA-6.