• Reproductive and Developmental Biology
• /
• v.32 no.4
• /
• pp.245-248
• /
• 2008

In the present studies, we have intended to compare the EDS (20% EG + 20% DMSO + 0.4 M sucrose + 10% FCS) and EDT (20% EG + 20% DMSO + 0.3 M trehalose 10% FCS) methods for vitrification of canine oocytes, in order to improve the vitrification methods. The survival rate of vitrified-thawed oocytes using the EDS method was $15.1{\pm}1.8%$ (p<0.05), which was lower than that of the control group $(66.7{\pm}2.5%)$. About $45{\sim}55%$ of the vitrified-warmed oocytes showed normal morphology, as assessed by PI staining. However, the ratio of survival rate of oocytes showed lower than that of normal morphology in comparison between EDS method and control group. The survival and developmental rates of vitrified-warmed oocytes by the EDS and EDT methods were $16.7{\pm}1.4%\;and\;11.1{\pm}0.8%$ and $8.3{\pm}1.4%\;and\;4.4{\pm}1.8%$, respectively (p<0.05). The results were significantly lower than the control group $(66.7{\pm}2.5%\;and\;16.7{\pm}3.7%)$. However, the survival rate of vitrified-warmed oocytes using EDS method showed higher than that in the ETS group.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.29 no.7 s.238
• /
• pp.868-877
• /
• 2005

We performed the experimental and the numerical study on the comparison of thermal comfort performance indices for cooling loads in the lecture room for 4 cases: Fan coil unit(FCU) or 4-way cassette air-conditioner is respectively operated with the ventilation system or without. We measured the velocity, the temperature distribution and predicted mean vote(PMV) value in the lecture room for 4 different air-conditioning methods. Effective draft temperature(EDT) and PMV were investigated to analyze the characteristics of two thermal comfort indices in the lecture room and to compare their values each other. From the results we knew that there is the similarity between PMV values and EDTs when the room is air-conditioned for cooling loads. It turned out that definition of the control temperature is very important when the EDT is calculated. Finally EDT should not be used to predict the accurate thermal comfort in case that the temperature and humidity are suddenly varied and the zone affected by the solar and inner wall radiation.

• Journal of Microbiology and Biotechnology
• /
• v.29 no.4
• /
• pp.548-557
• /
• 2019

Staphylococcus species have a ubiquitous habitat in a wide range of foods, thus the ability to identify staphylococci at the species level is critical in the food industry. In this study, we performed rapid identification of Staphylococcus species using Matrix-Assisted Laser Desorption/Ionization Time-of-Flight mass spectrometry (MALDI-TOF MS). MALDI-TOF MS was evaluated for the identification of Staphylococcus reference strains (n = 19) and isolates (n = 96) from various foods with consideration for the impact of sample preparation methods and incubation period. Additionally, the spectra of isolated Staphylococcus strains were analyzed using principal component analysis (PCA) and a main spectra profile (MSP)-based dendrogram. MALDI-TOF MS accurately identified Staphylococcus reference strains and isolated strains: the highest performance was by the EX method (83.3~89.5% accuracy) at species level identification (EDT, 70.3~78.9% accuracy; DT, less than 46.3~63.2% accuracy) of 24-h cultured colonies. Identification results at the genus level were 100% accurate at EDT, EX sample preparation and 24-h incubation time. On the other hand, the DT method showed relatively low identification accuracy in all extraction methods and incubation times. The analyzed spectra and MSP-based dendrogram showed that the isolated Staphylococcus strains were characterized at the species level. The performance analysis of MALDI-TOF MS shows the method has the potential ability to discriminate between Staphylococcus species from foods in Korea. This study provides valuable information that MALDI-TOF MS can be applied to monitor microbial populations and pathogenic bacteria in the food industry thereby contributing to food safety.

• Journal of Trauma and Injury
• /
• v.30 no.4
• /
• pp.166-172
• /
• 2017

Purpose: Thoracic traumas represent 10-15% of all traumas and are responsible for 25% of all trauma mortalities. Traumatic cardiac injury (TCI) is one of the major causes of death in trauma patients, rarely present in living patients who are transferred to the hospital. TCI is a challenge for trauma surgeons as it provides a short therapeutic window and the management is often dictated by the underlying mechanism and hemodynamic status. This study is to describe our experiences about emergency cardiac surgery in TCI. Methods: This is a retrospective clinical analysis of patients who had undergone emergency cardiac surgery in our trauma center from January 2014 to December 2016. Demographics, physiologic data, mechanism of injuries, the timing of surgical interventions, surgical approaches and outcomes were reviewed. Results: The number of trauma patients who arrived at our hospital during the study period was 9,501. Among them, 884 had chest injuries, 434 patients were evaluated to have over 3 abbreviated injury scale (AIS) about the chest. Cardiac surgeries were performed in 18 patients, and 13 (72.2%) of them were male. The median age was 47.0 years (quartiles 35.0, 55.3). Eleven patients (61.1%) had penetrating traumas. Prehospital cardiopulmonary resuscitations (CPR) were performed in 4 patients (22.2%). All of them had undergone emergency department thoracotomy (EDT), and they were transferred to the operating room for definitive repair of the cardiac injury, but all of them expired in the intensive care unit. Most commonly performed surgical incision was median sternotomy (n=13, 72.2%). The majority site of injury was right ventricle (n=11, 61.1%). The mortality rate was 22.2% (n=4). Conclusions: This study suggests that penetrating cardiac injuries are more often than blunt cardiac injury in TCI, and the majority site of injury is right ventricle. Also, it suggests prehospital CPR and EDT are significantly responsible for high mortality in TCI.

• Journal of Surface Science and Engineering
• /
• v.16 no.4
• /
• pp.199-214
• /
• 1983

Up to this date, numerous methods of analysis of electroplating solutions are published. Some, however, need lots of works before reaching final results, or require high technique and special instruments, and also some are unaccurate due to unclearnes of end point. Like our undevelope countries, technicians of electoplating shops are most high school gradutes or under, and have not much knowledge on chemistry. Furthermore, those technicians have to control their plating solutions by themselves without having enough analytical laboratory equiIJment. Therefore, in this paper the simplest, besides accurate method is investigated after comparing nu.merous methods published. Among the methods of 'copper determinations from acid and alkaline copper plating baths, EDT A titration method are chosen, due to these methods are the simplest and fastest for the evaluation of metal content, without requiring any special instrument. For acid copper solutions, chelate titrations were accurate enough. Since the end point of titration of chelate method is variable according to the kind of .indicators androther metal's coexsistence as well as solution comIJonent, many difficulties were encountered from cyanide' copper, on the contrary of acid copper bath. PAN, PV, and MX indicators were tried, but it is found that MX is the best. In cyanide solution, due to cyanide is the masking reagent, elimination of this component is essential, and finally found that elimination eN- by precipitation with AgN03 solution was the simplest and the most accurate way among others. This method was very accurate for the new plating solutions even coexistence with organic brightners. However used solutions for long months running have to be predetermined the accurate copper value by thiosulfate method from time to time, before chelate titration by means of AgN03 precipitation. Always some constant deviatioJ;ls will be seen according to the solutions nature. Therefore those deviation values have to be compensated each time.

• The Journal of the Acoustical Society of Korea
• /
• v.37 no.5
• /
• pp.349-355
• /
• 2018

A large number of parameters have been defined in order to describe and to evaluate the acoustical propeTies in rooms. Reverberation time is an impoTant characteristic of conceT halls, theaters and studios, etc. Over the years, a number of different methods for measuring the reverberation time have been developed, the most common being: the interrupted noise method, the integrated impulse response method, and the method of recording the room response to an impulsive source. However, the reverberation time can be changed by the measurement method, sound source and microphone. Therefore, it is difficult to accurately measure the reverberation time in a room. In this paper, it will be analyzed the interpretation method of the reverberation time and discussed the limitations.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.15 no.3 s.96
• /
• pp.320-328
• /
• 2005

Last target of architectural acoustics is that people wish to convey voice effectively from the space adaptively in use purpose in building. But, how exactly through space sound (sound source) that wish to deliver from indoor can be passed method to do quantification and evaluate quantity of sound by method to serve indoor architectural acoustics estimation summer period and methods to estimate definition propose. This Study searches special quality of sound source about MLS signal that is occurred short-answer sound source (pistol sound source) and nondirectional speaker among indoor sound estimation method, and measure and analyzed reverberation time (RT60), definition (C80, D50) by regulation of each ISO 3382 in age place (classroom, hall, gymnasium). Analysis result and sound factor among could know that d of two sound sources converges in measurement error extent about reverberation time (RT60) of analysis incidental and sound factors and value shows change irregularly about sound factor of D50, C80, pistol sound source judged there is problem. Also, could know that problem is happened in deflection except reverberation time is in deflection analysis with wave that measure each in fixed distance in branch. Finally, when differ size of sound source and measure about change of sound pressure level in case measure sound pressure level giving difference about 10 dB, sound factor could know that there is no different effect.

• Journal of Microbiology and Biotechnology
• /
• v.14 no.2
• /
• pp.284-289
• /
• 2004

A PCR assay for the rapid detection of Vibrio vulnificus strains was developed using a virulence gene for elastase found in various Vibrio species. The DNA sequences in the elastase gene facilitated the identification of a species-specific probe for pathogenic V. vulnificus strains from both clinical and environmental sources. Using an elastase gene-based PCR reaction, a species-specific 507-bp PCR product was visualized by agarose gel electrophoresis. Three different DNA extraction methods were then compared to improve the simplicity and rapidity of detection. A PCR assay using the conventional DNA extraction or boiling method was able to detect as few as 25 V. vulnificus cells, making the detection limits at least 1-log-scale lower than that for the EDT A-treated DNA extraction method. In particular, the boiling method, which does not require purification of the chromosomal DNA, was very effective in terms of simple and rapid detection. Meanwhile, the detection limit in a mixed bacterial culture that included other bacteria, such as Escherichia coli or Bacillus subtilis, was two V. vulnificus cells, which was 1-log-scale lower than that for the control. Accordingly, when coupled with a new DNA extraction method, the elastase gene-based PCR can provide a rapid, specific, and sensitive method for identifying V. vulnificus in clinical and environmental samples.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.08a
• /
• pp.189-189
• /
• 2012

Lead sulfide (PbS) nanocrystal quantum dots (NQDs) are promising materials for various optoelectronic devices, especially solar cells, because of their tunability of the optical band-gap controlled by adjusting the diameter of NQDs. PbS is a IV-VI semiconductor enabling infrared-absorption and it can be synthesized using solution process methods. A wide choice of the diameter of PbS NQDs is also a benefit to achieve the quantum confinement regime due to its large Bohr exciton radius (20 nm). To exploit these desirable properties, many research groups have intensively studied to apply for the photovoltaic devices. There are several essential requirements to fabricate the efficient NQDs-based solar cell. First of all, highly confined PbS QDs should be synthesized resulting in a narrow peak with a small full width-half maximum value at the first exciton transition observed in UV-Vis absorbance and photoluminescence spectra. In other words, the size-uniformity of NQDs ought to secure under 5%. Second, PbS NQDs should be assembled carefully in order to enhance the electronic coupling between adjacent NQDs by controlling the inter-QDs distance. Finally, appropriate structure for the photovoltaic device is the key issue to extract the photo-generated carriers from light-absorbing layer in solar cell. In this step, workfunction and Fermi energy difference could be precisely considered for Schottky and hetero junction device, respectively. In this presentation, we introduce the strategy to obtain high performance solar cell fabricated using PbS NQDs below the size of the Bohr radius. The PbS NQDs with various diameters were synthesized using methods established by Hines with a few modifications. PbS NQDs solids were assembled using layer-by-layer spin-coating method. Subsequent ligand-exchange was carried out using 1,2-ethanedithiol (EDT) to reduce inter-NQDs distance. Finally, Schottky junction solar cells were fabricated on ITO-coated glass and 150 nm-thick Al was deposited on the top of PbS NQDs solids as a top electrode using thermal evaporation technique. To evaluate the solar cell performance, current-voltage (I-V) measurement were performed under AM 1.5G solar spectrum at 1 sun intensity. As a result, we could achieve the power conversion efficiency of 3.33% at Schottky junction solar cell. This result indicates that high performance solar cell is successfully fabricated by optimizing the all steps as mentioned above in this work.

• Tuberculosis and Respiratory Diseases
• /
• v.50 no.4
• /
• pp.426-436
• /
• 2001

Background : Chronic obstructive pulmonary disease(COPD) is one of the major contributors to morbidity and mortality among the adult population. Cigarette smoking(CS) is undoubtedly the single most important factor in the pathogenesis of COPD. However, its mechanism is unclear. The current hypothesis regarding the pathogenesis of COPD postulates that an imbalance between proteases and antiproteases leads to the destructive changes in the lung parenchyma. This study had two aims. First, to evaluate the effect of CS exposure on histologic changes of the lung parenchyme, and second, to evaluate the effect of CS exposure on the expression of the gelatinolytic enzymes in BAL fluid cells in guinea pigs. Methods : Two groups of five guinea pigs were exposed to the whole smoke of 20 commercial cigarettes per day, 5 hours/day, 5 days/week, for 6weeks, and 12 weeks, respectively, using a smoking apparatus. Five age-matched guinea pigs exposed to room air were used as controls. Five or more sections were microscopically extamined(${\times}400$) and the number of cellular infiltration of the alveolar wall was measured in order to evaluate the effect of CS exposure on the histologic changes of lung parenchyme. The statistical significance was analyzed by a linear regression method. To evaluate the expression of the gelatinolytic enzymes in intraalveolar cells, BAL fluid was obtained and the intraalveolar cells were separated by centrifugation (500 g for 10 min at $4^{\circ}C$). Two sets of culture plates were loaded with $1{\times}10^6$ intraalveolar cells. One plate, contained O.1mM EDTA, a inhibitor of matrix metalloproteases(MMPs), and the other plate had no EDTA. Both plates were incubated for 48 hours at $37^{\circ}C$. After incubation, gelatinolytic protease expression in the supernatants was analyzed by gelatin zymography. Results : At the end of CS exposure, the level of blood carboxy Hb had increased significantly(4.1g/dl in control group, 24g/dl immediately after CS exposure, 18g/dl 30 min after CS exposure, 15g/dl 1 hour after CS exposure). Alveolar inflammatory cells were identified in the CS exposed guinea pigs. The number of alveolar cellular cells observed in a microscopic field ($400{\times}$) was $121.4{\pm}7.2$, $158.0{\pm}20.2$, $196.8{\pm}32.8$, in the control, the 6 weeks, and the 12 weeks group, respectively. The increased extent of inflammatory cellular infiltration of the lung parenchema showed a statistically significant linear relationship with the duration of CS exposure(p=0.001, $r^2=0.675$). Several types of gelatinolytic enzymes in the intraalveolar cells of CS exposed guinea pigs were expressed, of which some were inhibited by EDT A. However, the gelatinolytic enzymes were not expressed in the control groups. Conclusion : CS exposure increases inflammatory cellular infiltration of the alveolar wall and the expression of gelatinolytic proteases in guinea pigs. EDTA inhibits some of the gelatinolytic proteases. These findings suggest a possibility that CS exposure may increase MMP expression in the lungs of guinea pigs.