• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.783-787
• /
• 2007

Nowadays, vehicle becoming necessity is increasing gradually and is main cause of environmental problem. The current automobile noise measurement test method such as ISO 362 which have been used many countries contribute seriously to enforce the regulation of the noise rigidly and actively study vehicle's noise, using that method. However, the amendment of ISO 362 was completed under the international agreement due to the changes in vehicle's techniques and road conditions. In this study, the difference between the current ISO 362(or ECE R51) and new ISO 362(or new ECE R51) is estimated by the test using the practical car producing domestically because the Korean manufacturer have to be interested in new test method.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.58 no.4
• /
• pp.597-601
• /
• 2009

Green car such as a hybrid electrical vehicle and fuel cell vehicle is developed as a commercial target. UN/ECE/WP29 is developing GTR of HFCV and establishing the regulation and standard of electrical safety by ELSA. The regulation and standard about Electrical safety of vehicle are prescribed in ISO, UN/ECE, FMVSS, Japanese Attachment and so on, in case of insulation resistance is referred to keep more than 100/Vdc, 500/Vac. However, accurate method to measure insulation resistance agreeable to structure of vehicle does not exist now, it is actually that correctness of measurement drops according to the feature of battery and fuel cell stack. In this paper, the method to measure insulation resistance for protection against electrical shock by direct contact or indirect contact in Green Car will be indicated by making a comparison between the insulation measurement in standard of electrical safety and the experiment results for HEV and HFCV.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.162-168
• /
• 2013

Recently, there have been efforts in many countries to reduce social expenses and casualties resulting due to car accidents. As such, ASS (active safety systems) are being researched and developed to prevent accidents and target mitigation. Among many useful active safety systems, it has been reported that commercial AEBS (Advanced Emergency Braking System) effectively prevents accidents and reduces casualties simultaneously. Accordingly, it is necessary to set Korean AEBS standards, and this research analyzes international AEBS standards for this necessity. In addition to the evaluation methodology of AEBS ECE Regulation, this study suggests traffic scenarios that occur frequently in domestic road environments, and provides an evaluation system for AEBS of the scenarios. Finally, the performance and safety of AEBS are evaluated through field test.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.2
• /
• pp.31-38
• /
• 2010

Bus manufacturers have tested and studied the dynamic collapse behavior of a bus body structure in rollover since UN ECE established ECE Regulation 66 to provide the requirement for the strength of bus structure. In spite of the costly cycles of practical tests, however, it is still a hard task to meet the rollover regulation by means of local reinforcements in the bus structure. Therefore it is necessary to develop a well designed strategy for the rollover strength implemented in the early stage of vehicle development. In this study, the suitable development method for each design stage from a component to complete body structure was considered to make a well-established development process of a bus body structure for rollover safety. For the efficient approach of the concept design stage, a numerical model based on the plastic hinge theory was used instead of detailed shell models. After setting up the concept design for the component size and geometry, the shell model was used to confirm and optimize the whole structure composition. The process developed in this study was practically used as an effective method to predict the rollover behavior of a new bus body structure.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.1
• /
• pp.56-63
• /
• 2007

In case of bus rollover, the body structure of the bus should be designed to ensure the survival space for passengers. So, this study focuses on evaluating rollover strength through a computer simulation using the commercial code, LS-DYNA3D at the initial stage of vehicle development. For this study, section structure was modeled using a simple beam element, and impact boundary conditions required by ECE(Economic Commission for Europe) regulation No.66 were applied. In order to confirm the validity of the beam element bus model, the results compared with the test results and shell element bus model. The analysis errors from beam element bus model are due to the difference in strain energy of joint area between beam and shell model. In this study, a method for the joint modeling was suggested by using nonlinear springs to which the collapse mechanisms were applied.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.28-35
• /
• 1997

Occupant injuries are always possible in a rollover accident, one of the major accidents in a bus. Thus the structure of body frame should have sufficient strength to protect passengers under accidental loads,. ECE(Economic Commission for Europe) regulation No.66 prescribes that residual space shall be preserved in the passenger compartment during and after the structure has been subjected to the prescribed rollover test. Rollover test on a bus section was completed according to the regulation. The coordinates of body section before and after rollover were measured, and it was checked that the structure still complied with the requirements of residual space. Direct measurement on a bus is difficult because of its large size. Thus photogrammetry by photographing and 3 dimensional digital modeling was introduced, and the coordinates of each point were measured through this method.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.6
• /
• pp.148-154
• /
• 1997

The safety problems of buses have been arisen due to the increasing of road traffic. Occupant injuries are always possible in the rollover accident and the frontal impact. Thus the structure of bus should have sufficient strength to protect passengers under accidental loads. ECE(Economic Commission for Europe) regulation No.66 prescribes that the superstructure of the vehicle shall be sufficient strength for passengers' surviving and the residual space shall be preserved in the passenger compartment during and after the standard rollover accident situation. Rollover test and simulation on a large-sized bus was completed according to the regulation. The coordinates of the points on the bus were measured by photogrammetry system. The rollover situation was revived by structural crashes simulation software, PAM-CRASH, and it was checked that the structure still complied with the requirements of residual space during rollover situation. The residual space was preserved during rollover, so it was proved that the structure of the investigated bus had much probability of survival in rollover accidents.

• Current Optics and Photonics
• /
• v.1 no.3
• /
• pp.207-213
• /
• 2017

The Adaptive Front-lighting System (AFS) is a part of the active safety system, providing optimized vision to the driver during night time and other poor-sight conditions of the road by automatic adaptation of lighting to environmental and traffic conditions. Basically, an AFS provides four different modes of the passing beam as designated in an United Nations Economic Commission for Europe regulation (ECE324-R123): neutral state or country light (Class C), urban light (Class V), highway light (Class E), and adverse weather light (Class W). In this paper, we first present an optics design for an AFS system capable of producing the Class C/V/E/W patterns requiring only on/off modulation of multi-array LEDs with no need for any additional mechanical components. The AFS optics consists of two separated modules, cutoff and spread; the cutoff module lights a narrow central area with high luminous intensity, satisfying the cutoff regulation, and the spread module forms a wide spread beam of low luminous intensity. Each module consists of two major parts; the first converts a discretely positioned LED array into a full-filled area emitting light source plane, and the second projects the light source plane to a 25 m away target plane. With the combination of these two optics modules, the four beam patterns are formed by simple on/off modulation of multi-array LEDs. Then we report the development of a prototype that was demonstrated to provide the four beam patterns.

• Journal of Energy Engineering
• /
• v.17 no.4
• /
• pp.227-232
• /
• 2008

Carbon dioxide is considered a major greenhouse gas that contributes to global wanning. $CO_2$ is a major component of the exhaust in the combustion of any hydrocarbon fuel. The regulation for $CO_2$ emission from vehicles has become much more stringent in recent years. These more stringent regulations require vehicle manufacturers to develop alternative fuels that reduce exhaust emissions. This paper evaluated the correlation of $CO_2$ emission and fuel economy in the Gasoline, Diesel, and LPG vehicles according to FTP-75 and NEDC(ECE15+EUDC) driving mode. From this study, we discovered that the decrease rate of $CO_2$ emission is higher for fuels of lower carbon concentration. When the relationship between $CO_2$ emission and fuel consumption rate according to used fuels is expressed as a function, one can find out that they have a high correlation. LPG vehicles produce less $CO_2$ emission than gasoline and diesel vehicles.

• Asian Pacific Journal of Cancer Prevention
• /
• v.14 no.2
• /
• pp.765-768
• /
• 2013

Background and Aims: Prostate cancer is the most commonly diagnosed cancer in males in many populations. Metformin is the most widely used anti-diabetic drug in the world, and there is increasing evidence of a potential efficacy of this agent as an anti-cancer drug. Metformin inhibits the proliferation of a range of cancer cells including prostate, colon, breast, ovarian, and glioma lines. MicroRNAs (miRNAs) are a class of small, non-coding, single-stranded RNAs that downregulate gene expression. We aimed to evaluate the effects of metformin treatment on changes in miRNA expression in PC-3 cells, and possible associations with biological behaviour. Materials and Methods: Average cell viability and cytotoxic effects of metformin were investigated at 24 hour intervals for three days using the xCELLigence system. The $IC_{50}$ dose of metformin in the PC-3 cells was found to be 5 mM. RNA samples were used for analysis using custom multi-species microarrays containing 1209 probes covering 1221 human mature microRNAs present in miRBase 16.0 database. Results: Among the human miRNAs investigated by the arrays, 10 miRNAs were up-regulated and 12 miRNAs were down-regulated in the metformin-treated group as compared to the control group. In conclusion, expression changes in miRNAs of miR-146a, miR-100, miR-425, miR-193a-3p and, miR-106b in metformin-treated cells may be important. This study may emphasize a new role of metformin on the regulation of miRNAs in prostate cancer.