• 한국전기전자재료학회논문지
• /
• 제19권12호
• /
• pp.1073-1077
• /
• 2006

Proton irradiation technology was used for improvement of switching characteristics of the PT-IGBT. Proton irradiation was carried out at 5.56 MeV energy with $1{\times}10^{12}/cm^2$ doze from the back side of the wafer. The I-V, breakdown voltage, and turn-off delay time of the device were analyzed and compared with those of un-irradiated device and e-beam irradiated device which was conventional method for minority carrier lifetime reduction. For proton irradiated device, the breakdown voltage and the on-state voltage were 733 V and 1.85 V which were originally 749 V and 1.25 V, respectively. The turn-off time has been reduced to 170 ns, which was originally $6{\mu}s$ for the un-irradiated device. The proton irradiated device was superior to e-beam irradiated device for the breakdown voltage and the on-state voltage which were 698 V and 1.95 V, respectively, nevertheless turn-off time of proton irradiated device was reduced to about 60 % compared to that of the e-beam irradiated device.

• 한국식품과학회지
• /
• 제29권4호
• /
• pp.771-775
• /
• 1997

본 연구는 병원성 Escherichia coli O157:H7 균주에 의한 식중독을 미연에 예방하고자 우육에 본 균주를 오염, 동결시켜 전자선에 의한 살균효과를 조사하였다. $37^{\circ}C$에서는 배양 16시간째에 최대균수를 나타내었고 $4^{\circ}C$에서는 균주의 증식이 거의 없었다. E. coli O157:H7 균주는 대수기나 정지기 모두가 $0^{\circ}C$ (chilled)와 $-18^{\circ}C$ (frozen)에서 배양시 약 $10^{7}\;CFU/mL$의 균수를 나타내었고 $-18^{\circ}C$에서는 $20^{\circ}C$ 보다 균주의 사멸율이 높았다. 동결육에 오염된 E. coli O157:H7 균주의 방사선 감수성은 $D_{(10)}$ 값이 0.45 kGy, 불활성화계수가 $3{\sim}5\;kGy$에서 $6.67{\sim}11.11$로 각각 나타났다. 본 결과로서 전자선 조사는 동결육에 오염된 E. coli O157:H7 균주의 제거방법으로 매우 효과가 있었다.

• 열처리공학회지
• /
• 제23권1호
• /
• pp.29-33
• /
• 2010

Titanium nitride (TiN) films were deposited on the polycarbonate substrate by using radio frequency (RF) magnetron sputtering without intentional substrate heating. After deposition, the films were bombarded with intense electron beam for 20 minutes. The intense electron irradiation impacts on the crystalline, hardness and surface roughness of the TiN films. The films irradiated with an electron beam of 300 eV show the small grains on the surface, while as deposited TiN films did not showany grains on the surface. Also the surface harness evaluated with micro indenter was increased up to 18 Gpa at electron energy of 900 eV after electron beam irradiation. In addition, surface root mean square (RMS) roughness of the films irradiated with intense electron beam affected strongly. The films irradiated by electron beam with 900 eV have the lowest roughness of 1.2 nm in this study.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.487-487
• /
• 2011

Recently graphene has emerged as a fascinating 2D system in condensed-matter physics as well as a new material for the development of nanotechnology. The unusual electronic band structure of graphene allows it to exhibit a strong ambipolar electric field effect with high mobility. These properties lead to the possibility of its application in high-performance transparent conducting films (TCFs). Compared to indium tin oxide (ITO) electrodes, which have a typical sheet resistance of ${\sim}60{\Omega}$/sq and ~85 % transmittance in the visible range (400?900 nm), the CVD-grown graphene electrodes have a higher/flatter transmittance in the visible to IR region and are more robust under bending. Nevertheless, the lowest sheet resistance of the currently available CVD graphene electrodes is higher than that of ITO. Here, we report an ingenious strategy, irradiation of MeV electron beam (e-beam) at room temperature under ambient condition, for obtaining size-homogeneous gold nanoparticle decorated on graphene. The nano-particlization promoted by MeV e-beam irradiation was investigated by transmission electron microscopy, electron energy loss spectroscopy elemental mapping, and energy dispersive X-ray spectroscopy. These results clearly revealed that gold nanoparticle with 10 ~ 15 nm in mean size were decorated along the surface of the graphene after 1.5 MeV-e-beam irradiation. A chemical transformation and charge transfer for the metal gold nanoparticle were systematically explored by X-ray photoelectron spectroscopy and Raman spectroscopy. This approach advances the numerous applications of graphene films as transparent conducting electrodes.

• Food Science and Biotechnology
• /
• 제18권2호
• /
• pp.390-395
• /
• 2009

Red radish seeds were irradiated at doses up to 8 kGy using electron beam (e-beam) and gamma ray ($\gamma$-ray). The seed viability and functional properties (carotenoid, chlorophyll, ascorbic acid, and total phenol) of sprouts grown from these irradiated seeds were evaluated. High germination percentage ($\geq$97%) was observed in seeds irradiated at $\leq$5 kGy, but the yield ratio and sprout length significantly decreased with increased irradiation dose. Irradiation at $\geq$6 kGy resulted in curling of the sprout roots. Sprouting enhanced the functional properties of red radish seeds as indicated by the increased carotenoid, chlorophyll, ascorbic acid, and total phenol contents during germination. However, radiation treatment hampered the growth of seeds resulting in underdeveloped sprouts with decreased carotenoid, chlorophyll, ascorbic acid, and total phenol contents. In general, e-beam and $\gamma$-ray irradiation of red radish seeds showed similar effects on the seed viability and functional properties of sprouts. Postharvest storage reduced the functional quality of sprouts.

• 한국표면공학회지
• /
• 제53권6호
• /
• pp.280-284
• /
• 2020

Electron beam irradiation is widely used as a type of surface modification technology to advance surface properties. In this study, the effect of electron beam irradiation on properties, such as surface hardness, wear resistance, roughness, and critical load of Titanium Aluminium nitride (TiAlN) films was investigated. TiAlN films were deposited on the SKD-61 substrate by using cathode arc ion plating. After deposition, the films were bombarded with intense electron beam for 10 minutes. The surface hardness was increased up to 4520 HV at electron irradiation energy of 1500 eV. In addition, surface root mean square (RMS) roughness of the films irradiated at 1500 eV shows the lowest roughness of 484 nm in this study.

• 한국식품저장유통학회지
• /
• 제21권3호
• /
• pp.381-387
• /
• 2014

식품의 방사선 조사는 식품 저장을 위한 성공적인 현대기술의 하나이지만 매우 신중하게 이루어져야 한다. 조사된 식품의 확인은 국제무역에서 소비자의 안전한 선택과 보호를 위해 가장 중요하다. 따라서 본 연구는 건조된 오징어와 문어에 전자선을 조사하여 선량별로 유도 생성되는 hydrocarbon류의 함량 및 분해패턴을 확인하였다. 비조사 시료와 선량별로 전자선 조사된 시료에서 지방을 추출한 뒤 solid phase extraction(SPE)방법을 이용하여 GC/MS로 확인하였다. 1, 3, 5, 7 및 10 kGy의 선량으로 전자선 조사된 건조 오징어와 문어에서 유도된 hydrocarbon류는 동일 선량에서 시료들의 지방산 조성에 따른 다른 생성률을 나타내었으며, 조사선량에 따라 증가하였다. 시료들에 다량 함유되어 있는 palmitic acid와 stearic acid로부터 생성된 1-tetradecene($C_{14:1}$), pentadecane($C_{15:0}$), 그리고 1-hexadecene($C_{16:1}$), heptadecane($C_{17:0}$)이 전자선 조사에 의해 유도된 주요 hydrocarbon류로 확인되었으며, 건오징어에서 hydrocarbon류 생성량이 건문어의 hydrocarbon류 생성량 보다 더 많음을 확인하였다. 이는 시료의 지방산 함유량에 따라 hydrocarbon류 생성량이 비례함을 알 수 있었다. 전자선 조사된 건오징어와 건문어에서 분석된 hydrocarbon류 중 1-tetradecene($C_{14:1}$), 1-hexadecene($C_{16:1}$) 그리고 heptadecane($C_{17:0}$)은 전자선 조사여부를 판별할 수 있는 지표로 활용될 수 있을 거라 사료된다.

• 방사선산업학회지
• /
• 제5권1호
• /
• pp.41-46
• /
• 2011

Polyacrylonitrile (PAN) fibers are the most widely used precursor of the materials for carbon fibers. The conventional process of carbon fibers from PAN precursor fiber includes two step; stabilization at low temperature and carbonization at high temperature. Compared to thermal stabilization, the stabilization process by electron beam (E-beam) irradiation is a advanced and brief method. However, a stabilization by E-beam irradiation was required a high dose (over 5,000 kGy) and spend over 1.5 hr (1.14 MeV, 1 mA). In the present work the main goal is exploring a quick stabilization process by cotrolling E-beam currents. The effect of various E-beam currents on stabilization of PAN precursor fiber was studied by gel fraction test, thermo gravimertic analysis (TGA), differential scanning calorimetry (DSC), tensile strength, and scanning electron microscopy (SEM) images.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.208-208
• /
• 2009

We used Brewster's Law to examine the mechanism of liquid crystal (LC) alignment on an organic insulation layer when subjected to ion-beam irradiation. Brewster's Law implies that the maximum rate polarized ray on a slanted insulation layers on the substrate and it illustrates the dependence of polarization and themechanical structure on the ion beam irradiation process. The pretilt angle of nematic LCs on the organic insulation surface was about $1.13^{\circ}$ for an ion beam exposure of $45^{\circ}$ for 1 minute at 1800eV. This shows the dependence of LC alignment on the polarization ratio in a slanted organic insulation layer.

• 폴리머
• /
• 제25권1호
• /
• pp.49-55
• /
• 2001

비닐계 단량체인 아크릴로니트릴과 스티렌을 E-beam 전조사법에 의해 폴리프로필렌 섬유에 그라프트 반응시켜 PP-g-(AN/St) 공중합체를 제조한 후 아미드옥심기와 슬폰기를 도입하여 이관능성 이온교환섬유를 제조하였다. 그라프트율은 단량체 내에 아크릴로니트릴의 조성이 감소할수록 증가하였으며 최대 101.1%이었고 최대 아미드옥심화율은 7.2 mmol/g이었다. 또한 섬유상 이온교환체의 초기 열분해 온도는 120 ${\circ}C$ 이었고 함수율은 공중합체 내에 아미드옥심화율이 증가할수록 감소하였고 슬폰화율이 증가할수록 증가하는 경향을 나타냈다. APP-g-AN, SPP-g-St, ASPP-g-(AN/St) 이온교환체의 우라늄 흡착량은 각각 12.4, 34, 38mg/g이었으며 최적 흡착시간은 약 50시간이었다. 우라늄 흡착 실험결과, 본 실험에서 합성한 이온교환체 ASPP-g-(AN/St)는 $UO_2^{2+}$에 대하여 우수한 성능을 보였다.