• 한국공작기계학회논문집
• /
• 제14권3호
• /
• pp.16-22
• /
• 2005

It is difficult to separate those of NC controller from the error of machine tools because the conventional testing methods to inspect the performance are including the errors of moving system, therefore it has been used as the methods that compare the other controllers. Also, it is hard to predict the machine itself errors with the methods assembling the NC controller and moving system on machine because of the variable load conditions. In this study, the performance inspecting system was developed by analyse the $axis\_rotating$ properties of servo system finally outputting from NC controller. The axis torque was controlled by motor dynamometer and the rotating position accuracy was measured by this developed system.

• 한국정밀공학회지
• /
• 제12권2호
• /
• pp.87-96
• /
• 1995

The cutting force is the most important variable to understand the mechanics of ultra-precision machining. Most dynamometers, however, monitor the static cutting force only. But it is necessary to measure the dynamic cutting force to clarify the machinability of the material, the formation of the chip, chatter and the wear of the tool. In this research, measurement of the dynamic cutting force in order to clarify the machin-ability of the material, the formation of the chip, chatter and the wear of the tool has been conducted. A combined-type dynamometer which could measure the static cutting force and the dynamic cutting force by use of strain gauges and a piezo-film accelerometer has been developed. An analysis of the dynamometer also has been carried out.

• Journal of Mechanical Science and Technology
• /
• 제15권9호
• /
• pp.1248-1256
• /
• 2001

In this study, a test bed for vehicle longitudinal control is developed using a chassis dynamometer and real time 3-D graphics. The proposed test bed system consists of a chassis dynamometer on which test vehicle can run longitudinally, a video system that shows virtual driver view, and computers that control the test vehicle and realize the real time 3-D graphics. The purpose of the proposed system is to test vehicle longitudinal control and warning algorithms such as Adaptive Cruise Control(ACC), stop and go systems, and collision warning systems. For acceleration and deceleration situations which only need throttle movements, a vehicle longitudinal spacing control algorithm has been tested on the test bed. The spacing control algorithm has been designed based on sliding mode control and road grade estimation scheme which utilizes the vehicle engine torque map and gear shift information.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2000년도 추계학술대회논문집 - 한국공작기계학회
• /
• pp.45-50
• /
• 2000

While braking cars, a large amount of energy is taken into the brake system in a short period of time. This leads to some problems ; cracking of the disc, non-uniform wear of pad and disc, fade. Thus it is important to measure the contact thermal behaviour precisely between disc and pad. The measurements must be considered to design the brake system. The paper describes methods to analysis the problem of the thermal behavior on the ventilated disc with ANSYS-a program of FEA and a brake dynamometer. According to this way, the paper can present the error between the data by the dynamometer and the results of analysis by ANSYS.

• 한국자동차공학회논문집
• /
• 제11권4호
• /
• pp.211-219
• /
• 2003

The main study experiments to obtain engine torque of the vehicle during performance test of the recent automobile. Torque was measured through the engine dynamometer to produces engine torque of the vehicle but the research method calculated engine torque of the vehicle without the engine dynamometer. The performance of the vehicle receive various running resistance. The study certificates performance of certification before a certification of used vehicle didn't carry out and certificate. This way evaluated on road test and chassis dynamometer The result of the study shows that it is much possible to apply the test. After comparing the engine torque of road driving with that of chassis dynamometer, the results are approximately the same. When rapidly speeded up, the road-load vehicle can pitch in some degrees, which may result in the fluctuations of acceleration, and then affect on the engine torque. Therefore it is confirmed that this method is easier way to measure the performance of vehicles.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2008년도 춘계학술대회 논문집
• /
• pp.557-558
• /
• 2008

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.243-247
• /
• 2004

The dynamometers which had made in a long time ago could not control the input/output quantity of water minutely and was sensitive to a noise since it was controlled by an analog control method. Therefore, a fully digital controlled system was urgently required to be robust against various noises. In this paper, the new system which can control the amount of circulated water in dynamometer was developed. This system is consisted of an industrial digital type controller and a servo motor. The industrial PLC was used as a main controller for the developed system, and the actuator and servo motor were used to control the inlet and outlet valve independently. The torque signal of load cell was fed back to the main controller to regulate the diesel engines load. Generally, an input/output valve position of the old dynamometer was fixed with a proper situation for an engine output test and the torque was changed according to the time interval. However, the torque value for the dynamometer could not be constantly kept because of the variation of the input water flow and fluid characteristic. Therefore, the automatic control of an inlet and outlet valve should be performed to keep the constant torque. So, the PID control method was applied to solve this problem. Also, the development of a web-based remote control system was described in this paper. This software will give us the convenience of operation, the more efficient operations, and the reduced operator workload for operation of the dynamometer. The application results of the system have been verified at actual diesel engine field.

• 한국항공우주학회지
• /
• 제44권11호
• /
• pp.981-988
• /
• 2016

브레이크 동력계는 브레이크의 성능을 시험하는 장치로 시험구역, 기계적 관성구역, 전기모터 및 제어구역으로 구성된다. 혼성동력계는 기계적 관성 구역의 크기를 줄이고 전기모터를 이용하여 브레이크 작동에 따른 기계적 관성의 손실을 보상하는 방식으로 상대적으로 작은 기계적 관성 크기와 적은 비용으로 시험이 가능한 장점이 있다. 본 논문에서는 공간적 제약이 있는 실험실에 적절한 혼성동력계를 설계하였고, 설계된 혼성동력계에서 마찰계수 변화 등 주요 설계변수가 혼성동력계 제동성능에 미치는 영향을 분석하였다. 본 연구를 통해 축소된 기계적 관성에 의한 에너지 손실을 보상하기 위한 전기 모터의 토크를 측정하면 마찰재의 불량여부를 판단 할 수 있는 결과를 얻었다.

• 한국가스학회지
• /
• 제23권2호
• /
• pp.68-73
• /
• 2019

본 연구에서는 차대동력계 시험에서 수집한 자동차 배출가스자료를 엔진동력계에서 측정되는 동력계 단위로 변환하는 방법을 제안하였다. 엔진동력계 시험은 소요시간이 길고 비용이 높아 적용이 제한적일 경우 간편한 방법인 차대동력계 시험이 선호될 수 있다. 환산 방법은 거리기준 배출가스 자료에 모드 엔진효율을 고려하여 동력단위로 환산하는 방법이며 CO2 성분에 대해서 적용한 결과 환산 결과와 측정 결과 사이에 우수한 상관성을 확인하였다. 이 방법을 해외자료에 적용할 경우 CO2 배출성능에 대해 0.1% 이내로 일치함을 보였으나 CO, NOx 및 THC 와 같은 미량 배출성분 들은 같은 환산방법을 적용하기에는 상관성이 다소 떨어지며 추가적인 고려가 필요함을 보였다.

• 한국산학기술학회논문지
• /
• 제20권5호
• /
• pp.56-65
• /
• 2019

최근 자동차는 안전성, 편리성, 친환경 등의 목적으로 개발되고 있다. 특히, 자동차 안전성에 대한 인식이 중요하게 바뀌고 있다. 이에 따라, ADAS 개발로 인한 안전 시스템들이 등장하였다. 그러나 ADAS의 개발과 시험 평가를 통해 양산 되는 기간은 상당히 오래 걸린다. 따라서 본 논문에서는 ADAS 개발과 시험 평가에 필요한 기간을 단축시키기 위해 브레이크 다이나모미터를 개발 하였다. 또한 개발한 브레이크 다이나모미터는 국제 표준인 JIS D-0210을 만족하며, ADAS의 모드별로 사용자가 시험 조건과 시험 방법을 선택 하여 제동력을 평가할 수 있다. 그리고 개발하는 브레이크 다이나모미터의 신뢰성 검증을 위해 선행 연구에서 제안한 ACC, LKAS, AEB의 시나리오를 사용하였다. 개발한 브레이크 다이나모미터는 시험값과 선행 연구를 통해 제안된 ADAS 모드별 이론식에 의한 계산값을 비교하여 신뢰성을 검증하였다. 또한, 향후에는 ADAS의 실차시험이 불가능한 환경에서 ADAS 모드별 브레이크 부품의 성능 평가가 가능할 것으로 기대 된다.