• Journal of Aerospace System Engineering
• /
• v.12 no.2
• /
• pp.30-36
• /
• 2018

In this study, a small-scaled test system for a tip jet rotor was developed to contribute to the research on unmanned compound rotorcraft. The performance and dynamic characteristics of the tip jet rotor were investigated using the test system. The diameter of the tip jet rotor was set to 2m in consideration of the size of the test site and the pneumatic supply capacity of the. The rotating speed of the rotor was controlled by the pressure of the compressed air. The thrust and forces during the rotor rotation were measured using a load measuring device. A hydraulic actuator was installed for the dynamic test and full-bridge strain gages were attached to the root of each blade to measure the flap, lag, and torsion-wise responses generated when the rotor is excited by the actuator. The performance and dynamic characteristic tests were conducted at various rotor speeds and blade pitches. In order to check the validity of the test results, the results were also compared with the CAMRAD II analysis.

• KIEE International Transaction on Electrical Machinery and Energy Conversion Systems
• /
• v.2B no.3
• /
• pp.90-94
• /
• 2002

The line start permanent magnet (LSPM) motor has been developed facilitate to the design of the synchronous motor. The rotor of this motor is composed of interior permanent magnets and aluminum bars instead of rotor windings. It is difficult to predict the performance characteristics accurately, because many characteristics are produced by the aluminum rotor bars and the permanent magnets. Therefore, in this paper the dynamic characteristics of the LSPM motor are described and compared via the time-stepped finite element method with those of the cage-type induction motor to find the characteristics of the permanent magnets and the rotor bars in the LSPM motor.

• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.18 no.1
• /
• pp.35-46
• /
• 2008

Harmonic vibration characteristics for the general rotor model having a breathing crack are analyzed. Analyses are performed at the half critical speed ranges. The vibration characteristics are explained by using the additional slope and bending moment at the crack position and the influence coefficient showing the structural dynamic characteristics of the rotor. With the low crack depth the magnitude of the additional slope is kept constant even at the speed range at which the orbit magnitude is very sensitive to the rotational speed change. At this speed range the vibration is affected by the influence coefficient only. As the dynamic bending moment exceeds the static bending moment with the increase of crack depth. the additional slope affects the vibration amplitude of cracked rotor and the crack propagation rate increases.

• Tribology and Lubricants
• /
• v.30 no.1
• /
• pp.64-70
• /
• 2014

This paper presents a numerical model for investigating the structural dynamics response of a rigid rotor supported on deep-groove ball bearings. The numerical model was used to investigate the influence of race waviness on the dynamic characteristics of a rotor ball bearing system, which is very important from a design viewpoint. The forth-order Runge-Kutta numerical integration technique was applied to determine the time displacement response, Poincare map, and frequency spectra. The analysis demonstrated that the model can be used as a tool for predicting the nonlinear dynamic behavior of a rotor ball bearing system under different operating conditions. The results of this study may help further understanding of the nonlinear dynamics of a rotor bearing system.

• Journal of Advanced Marine Engineering and Technology
• /
• v.10 no.4
• /
• pp.31-40
• /
• 1986

With the tendency toward high speed and high pressure in centrifugal pumps, the problem of sub-synchronous vibration has arisen, caused by the hydraulic forces of the working fluid, such as wearring, balance piston, impeller, etc.. These forces can drastically alter the rotor critical speeds and stability characteristics, and can be acted significant destabilizing forces. For preventing such self-excited vibration, the desing of the rotor system needs, which would secure the stability of the machine. In this paper, a procedure is presented for dynamic modeling of rotor-bearing-seal-impeller systems which consist of rigid disks, distributed parameter finite rotor elements and discrete bearings, seals and impellers. A finite element model including the effects of rotatory inertia and gyroscopic moments is developed using the consistent matrix approach. The technique of dynamic matrix reduction is applied to the shaft matrices to reduce them to a set of matrices of dynamic of significantly fewer degrees of freedom. The representation of bearing, seal and impeller elements is in term of linearized stiffness and damping matrices by reasonably small perturbations from equilibrium. The stability behavior of a typical double suction centrifugal pump is presented. Results show the influence of clearance and flow conditions on running speeds and stability characteristics.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2000.06a
• /
• pp.1450-1454
• /
• 2000

In order to understand dynamic characteristics of centrifugal compressor supported foil bearing, of which normal operating speed is about 20,000 ${\sim}$ 50,000 rpm, the rotor whirl is measured using gap sensors. Not only critical speeds of rotor system but also stability of rotor whirl, which are main concerns of the turbo compressor system, are measured using gap sensors by varying the rotating speed the rotor. The stiffness characteristics of bearing system is shown to be almost invariant according to speed variation by the measurement of eccentricity. In addition, from the directional power spectral density function of the measured vibration signal, the isotropy stiffness characteristics of foil bearing system is discussed.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2002.04a
• /
• pp.149-154
• /
• 2002

In a high speed spindle system, it is very important to monitor the state of rotating rotor. Particularly in active control spindle system, the position sensor must provide feedback to the control system on the exact position of the rotor. In order to monitor the state of a high speed spindle exactly, high accuracy and wide frequency bandwidth of sensors are important. This paper observes the factors which has an effect on dynamic performances of inductive position sensor.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.1
• /
• pp.52-58
• /
• 2018

A Study on the dynamic characteristics of a rotor driven by a tipjet system in hovering condition was carried out. The sectional modeling was performed for the tipjet blade in which the flow path was inserted, and the dynamic characteristics analysis was conducted by modeling the components of the proposed rotor system. The analysis was conducted with respect to the rotational speed and the collective pitch. As a result of the analysis, it was checked that the proposed tipjet rotor did not have aeroelastic instability within the designed operating range. The tipjet test equipment was constructed in order to verify the analysis approach. It was confirmed that the proposed rotor was driven normally by tipjet. The non-rotating eigenmode measurement test and the rotation test were performed, and the validity was proved by comparing the test results and the analysis results.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.48-53
• /
• 1989

We attempt to achieve both high dynamic performance and maximal power efficiency by means of linear decoupling of rotor speed (or motor torque) and rotor flux. The induction motor with our controller possesses the input-output dynamic characteristics of a linear system such that the rotor speed (or motor torque) and the rotor flux are decoupled. The rotor speed (or motor torque) responses are not affected by abrupt changes in the rotor flux and vice versa. The rotor flux need not be measured but is estimated by the well-known flux simulator. The effect of large variation in the rotor resistance on the control performances is minimized by employing a parameter adaptation method. To illuminate the significance of our work. we present simulation and experimental results as well as mathematical performance analyses.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2010.10a
• /
• pp.599-606
• /
• 2010

This paper presents dynamic analysis of FCEV (Fuel Cell Electric Vehicle) Turbo Blower. To analyze the dynamic characteristics of Turbo Blower, finite element model which consists of solid elements is constructed. Evaluation of stress for safety of rotor sleeve due to centrifugal force, Shrink fit analysis in maximum rotation speed is performed. Rotor dynamic analysis of Turbo blower is conducted using Campbell diagram and FEA (Finite element analysis) results are compared with experimental results to evaluate of validity of finite element model. To evaluate of Structure vibration characteristics, Modal analysis and forced vibration analysis are performed through FEA and experiment.