• 한국재료학회지
• /
• 제30권10호
• /
• pp.502-508
• /
• 2020

This paper focuses on the electrical properties and stability against DC accelerated aging stress of ZnO-V₂O₅-MnO₂-Nb₂O₅-Bi₂O₃-Co₃O₄-Dy₂O₃ (ZVMNBCD) varistor ceramics sintered at 850 - 925 ℃. With the increase of sintering temperature, the average grain size increases from 4.4 to 11.8 mm, and the density of the sintered pellets decreases from 5.53 to 5.40 g/㎤ due to the volatility of V₂O₅, which has a low melting point. The breakdown field abruptly decreases from 8016 to 1,715 V/cm with the increase of the sintering temperature. The maximum non-ohmic coefficient (59) is obtained when the sample is sintered at 875 ℃. The samples sintered at below 900 ℃ exhibit a relatively low leakage current, less than 60 mA/㎠. The apparent dielectric constant increases due to the increase of the average grain size with the increase of the sintering temperature. The change tendency of dissipation factor at 1 kHz according to the sintering temperature coincides with the tendency of the leakage current. In terms of stability, the samples sintered at 900 ℃ exhibit both high non-ohmic coefficient (45) and excellent stability, 0.8% in 𝚫E_B/E_B and -0.7 % in 𝚫α/α after application of DC accelerated aging stress (0.85 E_B/85 ℃/24 h).

• 한국세라믹학회지
• /
• 제46권2호
• /
• pp.200-210
• /
• 2009

It is necessary to minimize the mismatch of sintering shrinkage between dielectric ceramic and Ni inner electrode layers for the purpose of developing the ultra high-capacity multi layered ceramic condenser(MLCC). Thus, low temperature sintering of dielectric $BaTiO_3$ ceramic should be precedently investigated. In this work, the influence of the milling condition on sintering behavior and electrical properties of $BaTiO_3$ ceramics was investigated in the $BaTiO_3$(BT)-Mg-Dy-Mn-Ba system with borosilicate glass as a sintering agent. As milling time increased, specific surface area(SSA) of the powder increased linearly, while both sinterability and dielectric property were found to be drastically decreased with an increasing SSA. It was also revealed that the sinterability of the excessively milled $BaTiO_3$ ceramics could be recovered by increasing Ba content, rather than increasing glass addition. These results suggest that the sintering behavior of $BaTiO_3$ ceramics under the high SSA was more strongly dependent on the transient liquid phase caused by Ba addition, than the liquid phase from additional glass.

• 한국세라믹학회지
• /
• 제46권2호
• /
• pp.146-154
• /
• 2009

It is necessary to minimize the thickness of Ni inner electrode layer and to improve the coverage of inner electrode, for the purpose of developing the ultra high-capacity multi layered ceramic capacitor (MLCC). Thus, low temperature sintering of dielectric $BaTiO_3$ ceramic should be precedently investigated. In this work, the relationship between dielectric properties of MLCC and batch condition such as mixing and milling methods was investigated in the $BaTiO_3$(BT)-Dy-Mg-Ba system with borosilicate glass as a sintering agent. In addition, several chip properties of MLCC manufactured by low temperature sintering were compared with conventionally manufactured MLCC. It was found that low temperature sintered MLCC showed better DC-bias property and lower aging rate. It was also confirmed that the thickness of Ni inner electrode layer became thinner and the coverage of inner electrode was improved through low temperature sintering.

• 보존과학회지
• /
• 제6권1호
• /
• pp.15-30
• /
• 1997

전남지역 도요지에서 출토된 토기, 시유도편, 녹청자와 청자편의 제조기술과 산지추정은 X선회절분석, 유도결합 플라즈마 발광분석, 열기계적 분석을 통한 물리화학적 성질의 검토로 이루어졌다. 도편의 사용원료는 점토, 석영, 장석광물로 유사하지만 그 함량비는 출토지에 따라 약간의 차이가 있으며, 철분함량에서 토기, 흑갈유, 녹갈유 도편은 $4\~7\%$, 녹청자 및 청자편은 $2\~3\%$로 기종에 따라 두드러진 차이를 나타내고 있다 흑갈유, 녹청자의 구성광물은 $\alpha-Quartz$, mullite와 일부 tridymite, cristobalite로 이루어졌으며, 청자는 $\alpha-Quartz$, mullite만으로 구성되어 있다. 도편의 소성온도는 토기가 $1000\~1100^{\circ}C$, 흑갈유, 녹갈유, 녹청자 청자가 $l130\~1200^{\circ}C$ 정도로 추정되었다. 도편에 대한 출토지의 구분은 분석된 21개의 미량원소중 14개의 원소가 매우 근접되어 불가능하였으며, 도자기제조에 사용된 원료의 지질학적인 특성이 유사한 것으로 판단하였다. 이들 지역에서 출토된 도편의 특성원소는 Rb, Sr, V, Zr, Y, Nd, Sc, La, Ce, Nb, Sm, Eu, Dy, Yb로 14개이다. 영암의 도편은 Zn과 Fe원소에 의해 다른 지역에서 출토된 도편들과 명확히 구분되었고, 출토지가 다른 녹청자, 청자편은 동일한 범위에 군집되는 특징을 나타내어 사용원료가 비슷한 것으로 추정된다.

• 한국세라믹학회지
• /
• 제42권7호
• /
• pp.490-496
• /
• 2005

The electrical properties and stability of the varistors composed of ZnO-Pr$_{6}$O$_{11}$-CoO-Cr$_{2}$O$_{3}$-Dy$_{2}$O$_{3}$ system were investigated with sintering time in the range of 1$\~$3 h at 1350$^{\circ}C$ . As the sintering time was increased, the varistor voltage and leakage current increased, but the nonlinear exponent decreased. The varistors sintered for 1 h exhibited excellent nonlinearity, with a nonlinear exponent of 55.3 and a leakage current of 0.1 $\mu$A, whereas presented relatively low stability. The varistors sintered for 2 h exhibited not only high nonlinear exponent of 46.3, low leakage current of 0.3 $\mu$A, low dielectric dissipation factor of 0.0431, but also the highest stability, in which the variation rates of varistor voltage, nonlinear exponent, leakage current, dielectric constant, and dielectric dissipation factor were -3.0$\%$, -4.1$\%$, +3056.2$\%$, +5.1$\%$, and -12.5$\%$, respectively, after DC accelerated aging stress state of 0.95 V$_{1ma}$/150$^{\circ}C$/24 h. On the whole, the nonlinearity and stability of these varistors are greatly affected by the sintering time.

• 한국염색가공학회지
• /
• 제33권3호
• /
• pp.97-104
• /
• 2021

In this study, the dyeability of m-aramid fabric with various cationic dyes using two bath two step dyeing method were investigated. The exhaustion properties of Doracryl series recommend for aramid(Doracryl^® Red GL 100%(DR), Doracryl^® Blue GL 300%(DB), Doracryl^® Yellow XGRL 200%(DY)) and commercial cationic Synocryl series(Synocryl^® Red GRL ED(SR), Synocryl^® Blue GSL ED(SB), Synocryl^® Yellow 3RL ED(SY)) for acrylic were measured by using Dye-O-meter. In the presence of carrier, the exhaustions of Doracryl series were higher to those of Synocryl series and the opposite phenomenon was observed in the absence of carrier. And the severe migrations of cationic dyes to acetate, nylon and wool fabrics were observed without carrier.

• 한국반도체및디스플레이장비학회:학술대회논문집
• /
• 한국반도체및디스플레이장비학회 2006년도 추계학술대회 발표 논문집
• /
• pp.22-25
• /
• 2006

Long lasting phosphor materials are in great demand for their applications in the area of light emitting diodes (LEDs), commercial displays and warning signals. After glow longevity, brightness, photo-resistance and chemical and environment stability are most important qualities that are desired for these materials. Alumina as host lattice with various rare earth elements has been found to be good at the same time inexpensive material for the synthesis of the phosphor materials. This communication explored the effect of mixed rare earth metal on the luminescence properties of these materials for the first time. Various permutations and combinations of $Sr^{2+}$ and $Ba^{2+}$ have been investigated in order to achieve robust and high luminescence characteristics in the tailored phosphor materials.

• The Korean Journal of Ceramics
• /
• 제1권2호
• /
• pp.91-95
• /
• 1995

Polycrystalline bismuth- and aluminum- substituted dysporsium and yttrium iron garnet (Bi2R3-xAlyFe5-yO12, R=Dy or Y, $0\leqx\leq3, \; 0\leqy\leq3$) films have been prepared by pyrolysis. The crystallization temperatures, the solubility limit of bismuth ions into the garnet phase, and magnetic and magneto-optic properties of the films have been investigated as a function of bismuth and aluminum concentration. It was found that the crystallization temperatures as a function of bismuth and aluminum concentration. It was found that the crystallization temperatures of these films rapidly decreased as bismuth concentration. It was found that the crystallization temperatures of these films rapidly decreased as bismuth concentration (x) increased up to x=1.5 and then remained temperatures of these films rapidly decreased as bismuth concentration (x) increased up to x=1.5 and then remained unchanged at x>1.5, whereas, showed no changes as aluminum concentration (y) increased up to y=1.0 and then gradually increased at y>1.0. The solubility limit of bismuth ions was x=1.8 when y=0 but increased to x=2.3 when y=1.0. It was demonstrated that the magnetic and magneto-optic properties of the dysprosium iron garnet films could be tailored by bismuth and aluminum substitution suitable for magneto-optic recording as follows. The saturation magnetization and coercivity data obtained for the films indicated that the film composition at which the magnetic compensation temperature became room temperature was y=1.2 when x=1.0. Near this composition the coercivity and the squareness of the magnetic hysteresis loop of the films were several kOe and unit, respectively. The Curie temperatures of the films increased with the increase of x but decreaed with the increase of y, and was 150-$250^{\circ}C$ when x=1.0 and y=0.6-1.4. The Faraday rotation at 633 nm of the films increased as x increased but decreased as y increased, and was 1 deg/$\mu\textrm{m}$ when x=1.0 and y=1.0. Based on the data obtained, the appropriate film composition for magneto-optic recording was estimated as near x=1.0 and y=1.0 or $BiDy_2AlFe_4O_{12}$.

• Bulletin of the Korean Chemical Society
• /
• 제34권2호
• /
• pp.374-378
• /
• 2013

Two novel binuclear metal-organic coordination complexes [$Cd_2(Hdpa)_4(bpy)_2$] (1), [$Dy_2(dpa)_2(bpy)_2(NO_3)_2-(H_2O)_2$](bpy) (2) (where $H_2dpa$ = biphenyl-2,2'-dicarboxylic acid, bpy = 2,2'-bipyridine) have been synthesized under hydrothermal conditions and characterized by single crystal X-ray diffraction, spectral method (IR), elemental analysis (EA), powder X-ray diffraction (XRD), electronic spectra (UV-vis), fluorescent in the solid state and thermogravimetric analysis (TGA). Complexes 1-2 crystallizes isomorphously in the Triclinic space group P-1. The ${\pi}-{\pi}$ stacking interactions and hydrogen-bonds play a vital role in determining the crystal packing and construction of the extended 3-D supramolecular network.

• 한국광물학회지
• /
• 제13권4호
• /
• pp.221-230
• /
• 2000

이성분 희토류 원소로 치환된 4종류의 합성불화인회석(synthetic fluorapatite) (Ap49: La+Gd, Ap50:Ce+Dy, Ap51: Pr+Er, Ap54: Eu+Lu; $Ca{10-x-2y}$ $Na_{y}$ $REE_{x+y}$($P_{1-x}$ //$Si_{x}$ $_{4}$)$_{6}$ $F_{2}$, x=0.13~0.12, y=0.26~0.42)을 대상으로 X-선 회절분석을 통해 얻어진 자료를 이용하여 리트벨트 구조분석을 실시하고 치환된 희토류원소의 거동을 단결정법으로 구해진 결과와 비교.분석하였다. 리트벨트 구조분석결과 합성불화인회석은 공간군 $P6_3$/m, 단위포는 평균하여 a=9.3906(1) $\AA$, c=6.8924(1) $\AA$, V=527.36 $\AA^3$의 값을 갖는다. 구조의 정밀도를 나타내는 R 지수를 보면 $R_{B}$ / 값은 17.29~18.80이고 S(GofF)값은 1.44~1.68로 계산되었다. 불화인회석은 9개의 산소를 배위하는 Ca1자리와 6개의 산소와 하나의 불소가 배위하는 Ca2자리가 있으며 Ca1-O의 평균거리는 2.563 $\AA$이고 Ca2-O의 평균거리는 $2.460 \AA$으로 Ca1자리가 Ca2자리보다 다소 크다. 구조자리 치환식에서는 $Ca^{2+}$ / 자리를 치환하는 $REE^{3+ }$ 로 인하여 전하균형을 맞춰주기 위해서 인과규소가 함께 참여하였다. ($REE^{3}$+Si$^{ 4+}$ $2Ca^{2+}$ : Ca1) 계산된 희토류원소의 자리점유율(REE-Ca2/REE-Cal)은 원자번호가 증가함에 따라 일정하게 감소하는 경향을 보여주며 이는 희토류원소의 거동이 LREE는 크기가 상대적으로 작은 Ca2 자리에 우선 치환되고 HREE는 크기가 큰 Ca1자리에 우선 치환되는 경향을 지시한다.