• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.49 no.5
• /
• pp.315-320
• /
• 2000

This paper presents the fabrication and test of a micropump with an electromagnetic actuator and a pair of aluminum flap valves. The actuator consists of a solenoid coil, a permanent magnet and an actuator diaphragm. The actuator diaphragm is fabricated by the spin coating of silicone rubber. The valve are passive ones and are fabricated by micromachining. The deflection of the fabricated actuator diaphragm is measured with a laser vibrometer. The deflection of the actuator diaphragm is proportional to the input current. The measured deflection of the fabricated diaphragm is $400 \mum$,/TEX> when the input is 118 mApp, and the cut-off frequency is 50 Hz. The maximum flow rate of the fabricated micropump with the electromagnetic actuator is about 5$0 \muell/min$ at 5 Hz when the input current and the duty ratio of the square was are 118 mApp and 50%, respectively.

• IEMEK Journal of Embedded Systems and Applications
• /
• v.7 no.6
• /
• pp.331-338
• /
• 2012

This paper presents a wireless sensor network protocol aimed for artificial structure monitoring. The proposed protocol enables the sensor network to operate at a low duty cycle for reducing power consumption with a high degree of synchronization accuracy. It also enables event-triggered measurement of environmental information with a high sampling rate and the transmission of the measured data with a low latency. The feasibility of the proposed protocol is demonstrated through experiments involving three sensor nodes and a sink node. Though a tunnel health monitoring was considered in the paper, the proposed protocol can be easily adopted in other areas.

• Proceedings of the KSME Conference
• /
• 2004.11a
• /
• pp.690-695
• /
• 2004

The present study is an investigation on the characteristics of heavy load toque converter by experimental process. To get the dynamic performance, the dynamometer was used with a parameters of speed, torque, oil pressure and oil flux, etc. The torque converter was tested for various input speed, output oil pressure and input oil flow rate. All experiments were investigated in case that the speed ratio is increased. The torque ratio and capacity factor was in inverse proportion to speed. Engine revolution had a more effects at region of low speed ratio. But, the opposite phenomena were represented increase of efficiency. In result of this experiments, the characteristics of torque converter were not influenced by oil pressure and oil flux.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2008.11a
• /
• pp.282-283
• /
• 2008

According to the development of vehicle technique, the improved NVH performance is required in the vehicle which have the high effectiveness and the high output of the powertrain. This vehicle has to be adapted to active engine mounting system to reduce the vibration in accordance with various vehicle information. The pneumatic active engine mounting system is consist with engine mount, solenoid valve, air tank and control unit totally. The important technique of this system is to reduce the vibration by the air pressure. This paper contains the development process of the pneumatic active engine mounting system and confirm the performance of this system test and vehicle test.

• Journal of ILASS-Korea
• /
• v.16 no.1
• /
• pp.51-57
• /
• 2011

An experimental study was performed to explore characteristics of combustion and exhaust emissions in the compression ignition engine of RCCI (reactivity controlled compression ignition) using diesel-gasoline dual fuel. A dual-fuel reactivity controlled compression ignition concepts is demonstrated as a promising method to achieve high thermal efficiency and low emissions. For investigating combustion characteristics, engine experiments were performed in a light-duty diesel engine over a range of SOIs (start of injection) and gasoline percents. The experimental results showed that cases of diesel-gasoline dual fuel combustion is capable of operating over a middle range of engine loads with lower levels of NOx and soot, acceptable pressure rise rate, low ISFC (indicated specific fuel consumption), and high indicated thermal efficiency.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.16 no.3
• /
• pp.56-63
• /
• 2007

Modern diesel vehicle has to comply with the EURO IV, V regulation with low level of particulate matter and smoke emission Moreover, emission standards of each countries are becoming stringent in advanced countries such as USA and Europe. Because Bio-diesel is similar to diesel fuel, it is essential to judge the environmental and health effects deriving from the use of Bio-diesel in diesel engine. The deterioration characteristics of emission in accordance with aging vehicles must be regulated for Bio-diesel. Therefore, under 1200 driving hours, 220,000km driving distance condition and full load, the deterioration characteristics of emission were estimated. We could reduce sulfur contents of fuel, particulate matter and smoke emission by using Bio-diesel and conform the influence of engine performance, emission, and fuel consumption by Bio-diesel deterioration

• Journal of information and communication convergence engineering
• /
• v.8 no.1
• /
• pp.122-128
• /
• 2010

Efficient energy management is a very important issue in wireless sensor network since wireless sensor nodes are usually battery-powered. Recently, S-MAC protocol based on low duty-cycle has been proposed to reduce energy consumption. Even though research effort has been made to evaluate performance of S-MAC by conducting various simulations, however, some important simulation parameters are not well evaluated yet. In this paper, we identify the performance of S-MAC under different amount of streams and different patterns such as data rate and traffic. Through analyzing the simulation results, we discover weakness of S-MAC as well as analyze impact of amount of streams and packet pattern.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.16 no.4
• /
• pp.63-68
• /
• 2008

Compared with past, helicopters have remarkably high level of safety and accidents due to mechanical defects are decreased about 15%. Most of their duties, however, are to commit at duty area which is hard to access. Because of them, collision probability is high and also has relatively higher accident rates than other aircraft with special mission. A result of analysis is that accident rate is relative high with prevention of disasters, putting out a fire and crop-dusting missions under 500ft. In addition, most of accidents are related with human factors. According to this, it is required to pilots who carry these mission that safety education and detailed analysis about their mission.

• Journal of Korean Society for Atmospheric Environment
• /
• v.18 no.5
• /
• pp.411-417
• /
• 2002

The purpose of this study is to evaluate the emission reduction characteristics depending on the formation of the catalyst which influences the development of the diesel oxidation catalyst (DOC) suitable for small-sized diesel engines. We also attempted to suggest the feasibility of it as an after-treatment device. The reduction efficiency of DOC for CO and HC was proportional to the contents of precious metals, and the particulate matter (PM) has been reduced as much as 53∼59%. The reduction rate of soluble organic fraction (SOF) by DOC attachment revealed 100%. The composition of sulfate in PM increased from 3%, 7∼11% by installation of DOC. It is described that increase of sulfate contributed to the production of PM. This result also showed that the SOF and sulfate have trade-off relationship.

• Transactions of the Korean Society of Machine Tool Engineers
• /
• v.10 no.1
• /
• pp.71-77
• /
• 2001

Experimental study if die-sinking electrical discharge machining(EDM) was conducted with rotating electrode system including inside hole for increasing the material removal rate(MRR). With the help of dielectric fluid flow through the inside according to the different internal diameter of the hole, the molten workpiece debris could be removed and flushed out during the EDM, Cold die alloy(SKD-1) was executed for different peak current and duty factor. From this study, the MRR was found to be increased with the peak current. The more MRR was obtained for the case of electrode inside diam-eter of 10 mm, but the MRR was decreased as the diameter near at the 4mm and 6mm. The values of surface roughness and roundness were analyzed under various conditions, and these were affected by the inside diameter change of electrode.