• The Journal of Asian Finance, Economics and Business
• /
• 제10권2호
• /
• pp.49-60
• /
• 2023

The study attempts to examine the relationship among revenue growth factors from different angles and provides a comprehensive overview of tax revenue collection for developing countries. The impact of income tax, customs duty, and value-added tax on the gross domestic product is examined using the ordinary least-square (OLS) multiple regression approach. To confirm the association, a multiple regression model is applied to time-series data. SPSS software, MS Excel, is used to draw the empirical results, trend analysis, and some graphical presentation to reach the study's objective. The findings show that while the value-added tax has a significant impact and the highest coefficient, regardless of country, income tax and customs duty may or may not be significant depending on the circumstances. It triggers effectual and efficacious economic growth. The paper has implications in policy-making areas where governments are seeking how to stimulate revenue growth effectively and efficiently. To promote economic growth, the tax net and tax rate on luxury goods should be increased along with human resources in the tax administration for the short term. But in the long term, decentralization & digitization of tax administration, dismantling the existing tax barriers and good governance are necessary.

• Journal of Biosystems Engineering
• /
• 제25권5호
• /
• pp.351-358
• /
• 2000

This study was conducted to develop a speed control system of a DC motor which drove a barley seeder mounted on a combine harvester. Barley seeder mounted on a combine has been known to reduce labor and cost of barley cultivation. However, development of the seeder has been unsuccessful because the combine, a dedicated rice and barley harvester has not enough space and proper power take-off for barley seeder. To develop a barley seeder, small powered motor speed controller was required. A proximity sensor for detecting working speed of the combine and a programmable one board microprocessor was used to develope a control system. Motor parameters and motor constant, relationship between seeding rate, motor speed, groove volumes of a tested roller, torque were measured. The proximity sensor sent a frequency signal to the microprocessor. In laboratory experiments, the excitation voltage of the motor was shown not to be proportional to the size of pulse width (duty ratio). A table transforming frequency signal, that represented for working speed to proper pulse width was developed from seeding rate experiments. However, seeding rate at low frequency signal was not proportional to the working speed. Seeding rate control proportional to the frequency signal was achieved by shifting of the frequency signal.

• 한국자동차공학회논문집
• /
• 제18권5호
• /
• pp.136-144
• /
• 2010

Exhaust gas recirculation (EGR) is an emission control technology allowing significant NOx emission reduction from light-and heavy duty diesel engines. The future EGR type, dual loop EGR, combining features of high pressure loop EGR and low pressure loop EGR, was developed and optimized by using a commercial engine simulation program, GT-POWER. Some variables were selected to control dual loop EGR system such as VGT (Variable Geometry Turbocharger)performance, especially turbo speed, flap valve opening diameter at the exhaust tail pipe, and EGR valve opening diameter. Applying the dual loop EGR system in the light-duty diesel engine might cause some problems, such as decrease of engine performance and increase of brake specific fuel consumption (BSFC). So proper EGR rate (or mass flow) control would be needed because there are trade-offs of two types of the EGR (HPL and LPL) features. In this study, a diesel engine under dual loop EGR system was optimized by using design of experiment (DoE). Some dominant variables were determined which had effects on torque, BSFC, NOx, and EGR rate. As a result, optimization was performed to compensate the torque and BSFC by controlling start of injection (SOI), injection mass and EGR valves, etc.

• 한국전자파학회논문지
• /
• 제14권12호
• /
• pp.1311-1320
• /
• 2003

본 논문에서는 RF 전자기장을 사용한 동물 및 세포 실험에서 전자기장 노출량의 정확성을 평가할 수 있는 방법을 제안하였다. 이를 위해 전자파 흡수율(SAR)을 전자기장 노출량의 단위로 사용한 동물 및 세포 연구 논문과 휴대폰 및 PDA에 대한 전자파 흡수율 시험 성적서를 대상으로 출력 전력, 전력 밀도 등과 SAR의 상관 관계 및 회귀 관계를 분석하였다. 동물 실험의 경우 전력 밀도와 SAR이, 세포 실험의 경우 출력 전력이 duty factor를 고려한 SAR과 통계적으로 유의한 상관 관계를 보였다. 회귀분석에서의 노출 불확실성을 평가하기 위해 결정계수값을 분석하였다. 각각의 실험장치 및 방법에 대한 해석 또는 측정 기법의 분석 이전에 본 연구 방법을 실시하여 대상 연구군의 특성을 고찰한다면 보다 효율적인 전자기장노출신뢰성 평가를 실시할 수 있을 것으로 판단된다.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2017년도 제48회 춘계학술대회논문집
• /
• pp.892-895
• /
• 2017

대형 가스터빈 연소기 구성품인 단일 압력선회식 연료분사기(Pressure swirl simplex liquid injector)를 설계, 분무특성 및 성능을 시험을 통해 평가하였다. 공급 압력 대비 분무 유량을 측정하여 설계점 기준 분무유량과 비교하였으며 섀도우그래프(Shadowgraph)를 통해 분무가시화이미지를 기록, 분무의 형상을 정성적으로 파악하고 분무각을 측정하였다. 시험 결과 동일한 공급압력 대비 측정된 분무유량은 설계점 기준 유량과 거의 일치하여 설계 및 제작의 정합성이 확인되었으며 섀도우그래프 이미지를 통해 연료분사기의 분무형상을 파악하고 설계 의도된 분무각이 나타남을 확인할 수 있었다. 이를 기반으로 향후 PDA(Phase Doppler Anemometry)를 통한 분무측정을 통해 보다 구체적인 연료 분사기의 분무 성능 및 특성을 파악할 수 있을 것으로 기대된다.

• 자동차안전학회지
• /
• 제13권3호
• /
• pp.78-85
• /
• 2021

Recently a traffic accident of heavy duty vehicles under the mandatory installation of ADAS (Advanced Driver Assistance System) is often reported in the media. Heavy duty vehicle accidents are normally occurring a high number of passenger's injury. According to report of Insurance Institute for Highway Safety, FCW (Forward Collision Warning) and AEB (Automatic Emergency Braking) were associated with a statistically significant 12% reduction in the rate of police-reportable crashes per vehicle miles traveled, and a significant 41% reduction in the rear-end crash rate of large trucks. Also many countries around the world, including Korea, are studying the effects of ADAS installation on accident reduction. Traffic accident statistics of passenger vehicle for business purpose in TMACS (Traffic safety information Management Complex System in Korea) tends to remarkably reduce the number of deaths due to the accident (2017(211), 2018(170), 2019(139)), but the number of traffic accidents (2017(8,939), 2018(9,181), 2019(10,095)) increases. In this paper, it is introduced a traffic accident case that could lead to high injury traffic accidents by being equipped with AEB in a bus. AEB reduces accidents and damage in general but malfunction of AEB could occur severe accident. Therefore, proper education is required to use AEB system, simply instead of focusing on developing and installing AEB to prevent traffic accidents. Traffic accident of AEB equipped vehicle may arise a new dispute between a driver's fault and vehicle defect. It is highly recommended to regulate an advanced event data recorder system.

• 한국분무공학회지
• /
• 제29권2호
• /
• pp.68-74
• /
• 2024

As awareness of environmental pollution problems increases worldwide, interest in air pollutants is increasing. In particular, NOx and PM, which are major pollutants in diesel vehicles, are contributing significantly to emissions. As a result, its importance is increasing. In this study, based on research results applied to large diesel vehicles, the problem of natural regeneration caused by low exhaust gas temperature during low speed and low load operation is solved by applying a complex regeneration DPF that is not affected by temperature conditions to small diesel vehicles. The feasibility of application to small diesel vehicles was reviewed by measuring the emission reduction efficiency. As a result of the engine test, the power reduction rate and fuel consumption rate before and after device installation under full load conditions were 2.9% decrease and 3.5% increase, respectively, satisfying the standard for a 5% reduction, and as a result of the regeneration equilibrium temperature (BPT) test, the regeneration temperature was 310℃. appeared at the level. The reduction efficiency test results for the actual vehicle durability test equipment showed 97.3% PM, 51.0% CO, and 31.1% HC, while the city commuter vehicle had PM 97.5%, CO 61.7%, HC 40.0%, and the school bus vehicle had PM 96.8%, CO 44.4%, HC 34.3%, and low-speed logistics vehicles showed a reduction efficiency of 98.2% for PM, 36.0% for CO, and 45.7% for HC. Based on the results of this study, in the future, it is necessary to secure DPF technology suitable for all vehicle types through actual vehicle application research on temperature condition-insensitive composite regenerative DPF for medium-sized vehicles.

• 한국음향학회지
• /
• 제41권4호
• /
• pp.446-460
• /
• 2022

본 논문은 고반복률을 갖는 양상태 소나 시스템에서의 송신 직접파로 인한 표적 탐지율 저하를 적응형 필터를 이용하여 개선하는 알고리즘을 제안한다. 이러한 소나 시스템에서의 송신 직접파 제거는 실제 시스템을 운용하는 것에 치명적인 영향을 주기 때문에 이것을 제거하는 것이 아주 중요하다. 본 논문에서는 시뮬레이션과 해상 실험 데이터에 Normalized Least Mean Square(NLMS)와 Recursive Least Square(RLS) 알고리즘을 적용하여 성능을 평가하였다. 송신 직접파 성분과 표적 신호가 포함된 표적 방위의 빔 신호를 입력 신호로 사용하고 송신 직접파 성분이 있는 송신기 방위의 빔 신호를 원하는 신호로 사용하여 두 신호의 차를 최적화 하여 송신 직접파를 제거하고 표적 신호만 남긴다. 시뮬레이션에서 정합필터의 결과를 확인하였을 때 Linear Frequency Modultated(LFM)과 Generalized Sinusoidal Frequency Modulated(GSFM) 모두에서 송신 직접파가 잡음레벨까지 제거되고 GSFM의 경우 표적의 부엽이 20 dB 이상 감소하여 성능 개선이 있는 것을 확인하였다. 해상 실험에서 LFM은 송신 직접파의 레벨이 10 dB 감소하였고, GSFM은 송신 직접파의 레벨이 약 4 dB 감소하였고, 표적의 부엽이 약 4 dB 정도 감소하여 성능 개선이 있다는 것이 확인되었다.

• International Journal of Automotive Technology
• /
• 제6권3호
• /
• pp.221-227
• /
• 2005

Aim of this study is to investigate an aerodynamic effect of a drag-reducing device on a heavy-duty truck. The vehicle experiences two different kinds of aerodynamic forces such as drag and uplifting force (or downward force) as it is traveling straight forward at constant speed. The drag force on a vehicle may cause an increase of the rate of fuel consumption and driving instability. The rolling resistance of the vehicle may be increased as result of the negative uplifting or downward force on the vehicle. A device named roof-fairing system has been applied to examine the reduction of aerodynamic drag force on a heavy-duty truck. As for a engineering design information, the drag-reducing system should be studied theoretically and experimentally for the best efficiency of the device. Four different types of roof-fairing model were considered in this study to investigate the aerodynamic effect on a model truck. The drag and downward force generated by vehicle has been obtained from numerical calculation conducted in this study. The forces produced on four fairing models considered in this study has been compared each other to evaluate the best fairing model in terms of aerodynamic performance. The result shows that the roof-fairing mounted truck has bigger negative uplifting or downward force than that of non-mounted truck in all speed ranges, and drag force on roof-fairing mounted truck has smaller than that of non-mounted truck. The drag coefficient $(C_D)$ of the roof-fairing mounted truck (Model-3) is reduced up to $41.3\%$ than that of non-mounted trucks (Model-1). A downward force generated by a roof-fairing mounted on a truck is linearly proportional to the rolling resistance force. Therefore, the negative lifting force on a heavy-duty truck is another important factor in aerodynamic design parameter and should be considered in the design of a drag-reducing device of a tractor-trailer. According to the numerical result obtained from present study, the drag force produced by the model-3 has the smallest of all in all speed ranges and has reasonable downward force. The smaller drag force on model-3 with 2/3h in height may results of smallest thickness of boundary layer generated on the topside of the container and the lowest intensity of turbulent kinetic energy occurs at the rear side of the container.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집D
• /
• pp.896-902
• /
• 2001

To meet strict emission regulation while improving engine performances, common rail injection system which is suitable for electronic control, and capable of controlling injection quantity, timing, rate and pressure individually as well as realizing high pressure has been developed. At present study, a 8L DI diesel engine was converted to a single-cylinder experimental engine allowing optical access through an extended piston and a prototype of common rail injector in progress was applied to the engine. The combustion characteristics of the engine were analysed by using direct images and characteristics of the injector were analysed. We can not say that the results are always the same to general common rail injection system but that they are just characteristics of specific prototype injector.