• Journal of Korean Society for Atmospheric Environment
• /
• v.26 no.5
• /
• pp.567-580
• /
• 2010

Organic carbon (OC) and elemental carbon (EC) concentrations were determined for $PM_{10}$, $PM_{2.5}$ and $PM_{1.0}$ aerosols particles collected at Gosan Superstation on Jeju Island from August 2007 to September 2008. Aerosols were collected on quartz filters for 24 hours and then OC and EC were analyzed by TOR/IMPROVED method. Mean concentrations of OC and EC were $4.66\;{\mu}g/m^3$ and $1.69\;{\mu}g/m^3$ for $PM_{10}$, $3.95\;{\mu}g/m^3$ and $1.69\;{\mu}g/m^3$ for $PM_{2.5}$, and $3.16\;{\mu}g/m^3$ and $1.42\;{\mu}g/m^3$ for $PM_{1.0}$, respectively. The concentrations of OC and EC comprised 16.4% and 6.0% of $PM_{10}$, 22.9% and 9.8% of $PM_{2.5}$, and 23.0% and 10.0% of $PM_{1.0}$. OC and EC showed a clear seasonal variation with the highest in winter and the lowest in summer. The correlations between the two were also the best during the winter ($R^2$=0.87, 0.94, and 0.95 for $PM_{10}$, $PM_{2.5}$ and $PM_{1.0}$). The ratio of OC/EC exhibited the maximum (7.24) during an Asian dust event due to an increase of OC, which was possibly derived from soil. The mass fraction of both OC and EC was the highest in fall. When OC and EC concentrations were highly elevated, EC1 (the first EC fraction determined at $550^{\circ}C$) and pyrolyzed OC (POC) were dominant subcomponents in winter and OC3 (the third OC fraction determined at $450^{\circ}C$) and POC in spring.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.172-172
• /
• 2011

Anaerobic digestion(AD) has successfully been used for many applications that have conclusively demonstrated its ability to recycle biogenic wastes. AD has been successfully applied in industrial waste water treatment, stabilsation of sewage sludge, landfill management and recycling of biowaste and agricultural wastes as manure, energy crops. During AD, i.e. organic materials are decomposed by anaerobic forming bacteria and fina1ly converted to excellent fertilizer and biogas which is primarily composed of methane(CH4) and carbon dioxide(CO2) with smaller amounts of hydrogen sulfide(H2S) and ammonia(NH3), trace gases such as hydrogen(H2), nitrogen(N2), carbon monoxide(CO), oxygen(O2) and contain dust particles and siloxanes. The production and utilisation of biogas has several environmental advantages such as i)a renewable energy source, ii)reduction the release of methane to the atomsphere, iii)use as a substitute for fossil fuels. In utilisation of biogas, most of biogas produced from small scale plant e.g. farm-scale AD plant are used to provide as energy source for cooking and lighting, in most of the industrialised countries for energy recovery, environmental and safety reasons are used in combined heat and power(CHP) engines or as a supplement to natural. In particular, biogas to use as vehicle fuel or for grid injection there different biogas treatment steps are necessary, it is important to have a high energy content in biogas with biogas purification and upgrading. The energy content of biogas is in direct proportion to the methane content and by removing trace gases and carbon dioxide in the purification and upgrading process the energy content of biogas in increased. The process of purification and upgrading biogas generates new possibilities for its use since it can then replace natural gas, which is used extensively in many countries, However, those technologies add to the costs of biogas production. It is important to have an optimized purification and upgrading process in terms of low energy consumption and high efficiency giving high methane content in the upgraded gas. A number of technologies for purification and upgrading of biogas have been developed to use as a vehicle fuel or grid injection during the passed twenty years, and several technologies exist today and they are continually being improved. The biomethane which is produced from the purification and the upgrading process of biogas has gained increased attention due to rising oil and natural gas prices and increasing targets for renewable fuel quotes in many countries. New plants are continually being built and the number of biomethane plants was around 100 in 2009.

• Journal of Pharmaceutical Investigation
• /
• v.33 no.2
• /
• pp.145-149
• /
• 2003

Manufacturing facilities of the pharmaceuticals must meet certain level of the cleanness required so that foreign substances such as dust, moisture, heat, microorganism, or virus do not contaminate the product. In case of radiopharmaceuticals for medical treatment and diagnosis, not only should the operators and environment be protected from radiation but also need to be isolated from the foreign contaminant. Therefore, manufacturing facilities for radiopharmaceuticals must satisfy the design standards of both hot cell and clean room which are specified by GMP. However, standards of maintaining negative pressure for preventing spread of radioactive contaminant in isolated facilities conflict with the standards of maintaining positive pressure for keeping cleanness. To solve this problem, air pressure of hot cell was designed lower than in the adjacent area to meet standards of the radiation safety. To keep higher cleanness in certain part of the hot cell for filling, minimal relative positive pressure allows. In order to effectively maintain the cleanness that is required for production of Tc-99m generator, which takes 70% of whole demand of radiopharmaceuticals, the rooms placed in each side of production room are used as a buffer area and three lead hot cells are installed in production room. In this research, we established the appropriate engineered design concept for Tc-99m generator manufacturing facility, which satisfies both GMP cleanness standard for preventing particles, bacteria, other contaminants and the regulations of radiation safety for supervising and controlling the amount of radiation exposure and exhausted radioactivity. And the concept of multi-barrier buffer zones is introduced to apply negative air pressure for hot cell with first priority and to continue relative positive air pressure for clean room.

• Korean Journal of Health Education and Promotion
• /
• v.30 no.3
• /
• pp.59-73
• /
• 2013

Objectives: The study is aimed at examining the individual reasons and regional/environmental factors of online search on suicide using social big data to predict practical behaviors related to suicide and to develop an online suicide prevention system on the governmental level. Methods: The study was conducted using suicide-related social big data collected from online news sites, blogs, caf$\acute{e}$s, social network services and message boards between January 1 and December 31, 2011 (321,506 buzzes from users assumed as adults and 67,742 buzzes from those assumed as teenagers). Technical analysis and development of the suicide search prediction model were done using SPSS 20.0, and the structural model, nd multi-group analysis was made using AMOS 20.0. Also, HLM 7.0 was applied for the multilevel model analysis of the determinants of search on suicide by teenagers. Results: A summary of the results of multivariate analysis is as follows. First, search on suicide by adults appeared to increase on days when there were higher number of suicide incidents, higher number of search on drinking, higher divorce rate, lower birth rate and higher average humidity. Second, search on suicide by teenagers rose on days when there were higher number of teenage suicide incidents, higher number of search on stress or drinking and less fine dust particles. Third, the comparison of the results of the structural equation model analysis of search on suicide by adults and teenagers showed that teenagers were more likely to proceed from search on stress to search on sports, drinking and suicide, while adults significantly tended to move from search on drinking to search on suicide. Fourth, the result of the multilevel model analysis of determinants of search on suicide by teenagers showed that monthly teenagers suicide rate and average humidity had positive effect on the amount of search on suicide. Conclusions: The study shows that both adults and teenagers are influenced by various reasons to experience stress and search on suicide on the Internet. Therefore, we need to develop diverse school-level programs that can help relieve teenagers of stress and workplace-level programs to get rid of the work-related stress of adults.

• Particle and aerosol research
• /
• v.16 no.3
• /
• pp.65-72
• /
• 2020

In this study, the indoor fine dust concentration in an office of the Korea Knowledge Industry Center was measured for about 80 hours when the concentration of atmospheric PM_2.5 was very high. The effect of the operation of the air cleaner and the forced ventilation system on the indoor PM_2.5 was investigated, and the particle size distribution of the indoor and outdoor particles was analyzed. When forced ventilator and air purifiers were partially used, the indoor PM_2.5 concentrations were maintained between 27.7 ㎍/㎥ and 32.9 ㎍/㎥ when the atmospheric PM_2.5 was 127.7 ㎍/㎥ to 141.6 ㎍/㎥ during working hours. It is more effective to operate the air purifier without operating the forced ventilation system when the concentration of the PM_2.5 is high since the PM_2.5 penetrating the installed filter is continuously introduced indoor from the outside.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.38 no.4
• /
• pp.337-346
• /
• 2014

This study aimed to understand the mode characteristics of a droplet subject to periodic forced vibration and the detachment of a droplet placed on a plate surface. An surface was coated with Teflon to clearly observe the behavior of a droplet. The contact angle between the droplet and surface and the hysteresis were found to be approximately $115^{\circ}C$ and within $25^{\circ}C$, respectively. The coating process was performed in a clean room that had an environment with a low level of contaminants and impurities such as air dust, detergents, and particles. To predict the resonance frequency of a droplet, theoretical and experimental approaches were applied. Two high-speed cameras were configured to acquire side and top views and thus capture different characteristics of a droplet: the mode shape, the detachment, the separated secondary droplet, and the waggling motion. A comparison of the theoretical and experimental results shows no more than 18 discrepancies when predicting the resonance frequency. These differences seem to be caused by contact line friction, nonlinear wall adhesion, and the uncertainty of the experiment. For lower energy inputs, the contact line of the droplet was pinned and the oscillation pattern was axisymmetric. However, the contact line of the droplet was de-pinned as the oscillation became more vigorous with increased energy input. The size of each lobe at the resonance frequency is somewhat larger than that at the neighboring frequency. A droplet in mode 2, one of the primary mode frequencies, exhibits vertical periodic movement as well as detachment and secondary ejection from the main droplet.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.24 no.3
• /
• pp.263-271
• /
• 2014

Objectives: Along with the several cases of pulmonary disorders caused by exposure to indium that have been reported in Japan, China, and the United States, cases of Korean workers involved in processes that require handling of indium compounds with potential risk of exposure to indium compounds have also been reported. We performed biological monitoring for workers in various target manufacturing processes of indium, indium oxide, and indium tin oxide(ITO)/indium zinc oxide(IZO) in domestic factories. Materials: As biological exposure indices, we measured serum concentrations of indium using inductively coupled plasma mass spectrometry, and Krebs von den Lungen 6(KL-6) and surfactant protein D(SP-D) using enzyme-linked immunosorbent assays. We classified the ITO/IZO target manufacturing process into powdering, mixing, molding, sintering, polishing, bonding, and finishing. Results: The powdering process workers showed the highest serum indium level. The mixing and polishing process workers also showed high serum indium levels. In the powdering process, the mean indium serum concentration in the workers exceeded $3{\mu}g/L$, the reference value in Japan. Of the powdering, mixing, and polishing process workers, 83.3%, 50.0%, and 24.5%, respectively, had values exceeding the reference value in Japan. We suppose that the reason of the higher prevalence of high indium concentrations in powder processing workers was that most of the particles in the powdering process were respirable dust smaller than $10{\mu}m$. The mean KL-6 and SP-D concentrations were high in the powdering, mixing, and polishing process workers. Therefore, the workers in these processes who were at greater risk of exposure to indium powder were those who had higher serum levels of indium, as well as KL-6 and SP-D. We observed significant differences in serum indium, KL-6, and SP-D levels between the process groups. Conclusions: Five among the seven reported cases of "indium lung" in Japan involved polishing process workers. Polishing process workers in Korea also had high serum levels of indium, KL-6, and SP-D. The outcomes of this study can be used as essential bases for establishing biological monitoring measures for workers handling indium compounds, and for developing health-care guidelines and special medical surveillance in Korea.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.7
• /
• pp.2719-2726
• /
• 2010

The purpose of this study was to investigate the scientific basic grounds for the assessment of health and environmental diseases resulting from air pollutants in Pohang. For this study, we investigated pollutants, weather characteristics and concentration distribution of fine particles ($PM_10$) yearly and each season, using data from Air Quality Monitoring Stations. The properties of concentration distribution and seasonal fluctuation of $PM_10$ were studied qualitatively and quantitatively using CALPUFF, air dispersion model. The average concentration of $PM_10$ for each season was spring($75.7{\mu}g/m^3$)>summer($56.8{\mu}g/m^3$)>winter($53.6{\mu}g/m^3$)>fall( $52.7{\mu}g/m^3$). In the case of spring, high concentrations appear due to the Asian dust frequently occurring. The contributions of $PM_10$ classified by the types of pollution source in Pohang were point source 62%>mobile source 33%>area source 5%. An important point is that 97% of emissions were produced from the iron manufacture in steel industry. Therefore, it is necessary to control the emission sources of pollutants and to construct an observation system at Pohang steel industrial complex from now on. It’s time to control the risk factors for health and environmental disease to protect the health of resident in Pohang and its neighboring areas.

• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.29 no.1
• /
• pp.42-49
• /
• 2019

Objective: Chronic obstructive pulmonary disease(COPD) is characterized by persistent airflow limitations associated with chronic inflammatory response due to noxious particles or gases in the lung. Iron deficiency is associated with chronic inflammation, such as COPD. The aim of this study was to evaluate the relationship among iron deficiency, iron homeostasis, and inflammation in retired miners with COPD. Methods: The serum levels of ferritin, soluble transferrin receptor(sTfR), and transferrin saturation(TSat) as biomarkers for iron deficiency and high-sensitivity C-reactive protein(hsCRP) as a biomarker for inflammation and hepcidin as a biomarker for iron homeostasis were measured in 93 male subjects. Iron deficiency was defined as any one or more of (1) sTfR>28.1 nmol/L, (2) TSat<16%, and (3) ferritin< $12{\mu}g/L$. Results: Iron deficiency was found 28% of the study subjects. Median levels of serum hsCRP was significantly increased related to airflow limitation of COPD(GOLD 1, $0.09{\mu}g/dL$ vs. GOLD 2, $0.17{\mu}g/dL$ vs. GOLD $3{\leq}$, $0.30{\mu}g/dL$, p=0.010), and was positively correlated with hepcidin(p=0.009). Mean level of serum hepcidin was lower in COPD subjects with iron deficiency(p=0.004) and serum levels of hepcidin was negatively correlated with %$FEV_1$ predicted(p=0.030). Conclusions: These results suggest that high serum levels of hepcidin are related to severe airflow limitation or inflammation and can decrease iron availability, regardless of iron status.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.64 no.3
• /
• pp.25-32
• /
• 2022

To understand the distribution characteristics of PM_2.5 concentration in the Saemangeum Reclamation Area and nearby areas, three points of the background area, the occurrence area, and the affected area were selected and samples were collected for each season. The chemical composition was determined. As a result of analyzing the chemical composition contained in PM_2.5, NO₃^- (7.2 ㎍/m³), SO₄^2- (4.3 ㎍/m³), NH₄+ (4.3 ㎍/m³), OC (2.5 ㎍/m³), Si (1.3 ㎍/m³) m³) and EC (0.5 ㎍/m³) seemed to be the main components, and NO₃-, SO₄^2-, NH₄⁺, which are components that form secondary particles, occupied a large proportion. The composition ratio of PM_2.5 was investigated in the order of ion component (56.8%) > Unknown (27.4%) > carbon component (11.8%) > heavy metal component (4.0%). During the PM_2.5 high concentration case days, the ionic component accounted for 90.7% during atmospheric stagnation cases, whereas the chemical composition ratio was in the order of ionic component (51.7%) > heavy metal component (41.5%) > carbon component (6.8%) during yellow dust cases. It was found that the characteristic of PM_2.5 in the Saemangeum reclaimed land and surrounding areas is mainly influenced by outside (domestic and overseas) throughout the year. Ion components accounted for the largest portion of PM_2.5 components in this area, but there were few sources of SOx and NOx emission in the Seamangeum area, which are precursors for secondary particle formation. Therefore, it is judged that most of these are generated and influenced as a secondary reaction in the atmosphere from the outside.