• Proceedings of the Korean Vacuum Society Conference
• /
• 2012.02a
• /
• pp.530-530
• /
• 2012

Many practical applications of carbon nanotubes(CNTs) have been proposed and there have been attempts to utilize CNT films as transparent electrodes for solar cells and displays. Our group has considered the use of the CNT film as a thin film heater (TFH) and proposed it for the first time and reported the thermal behavior of the TFH made of single walled CNTs. However, due to the relatively high electrical resistance of the CNT film, using the TFH in application areas requiring high heat flux has been a difficult problem. To overcome this obstacle, we adopted a 'branch electrodes' concept to increase the film conductance dramatically. If two branch electrodes are inserted into a TFH whose original electrical resistance is R, the total resistance will be reduced to R/9. Because of the increased aspect ratio, the resistance of each segmented TFH will be reduced to R/3. Furthermore, since they are connected in parallel, the total resistance reduces to R/9. This could be extended to n branch electrodes, and the total resistance of the film will be reduced to R/(n+1)2, if the resistance of electrodes are negligibly small. We fabricated the heaters with different number of branch electrodes. The number of branch electrodes of the fabricated heaters are 0, 2, 4, 8 and their electrical resistance are 101.4, 39.5, 20.0, $15.4{\Omega}$, respectively. We applied 20V to each heater and monitored the temperature variations. We could achieve high heating temperature even with low voltage supply. This technique could be applied to relevant industrial applications which need high power film heater.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.20 no.1
• /
• pp.26-33
• /
• 2012

Competition between air transportation and railways has grown fiercer in major countries around the world with the rise of high-speed railways. In South Korea, air passenger travel has been rapidly decreasing since the initial launch of the Seoul-Pusan KTX line in 2004 and second opening that followed in 2010. Further expansion of the high-speed railway is expected. At present, research efforts to verify the validity of constructing an underwater express railway tunnel between Ho-nam and Jeju Island are taking place. Considering the possible high speed railway connection between Seoul and Jeju Island, this thesis has analyzed the choice behavior of existing passengers of the major and low-cost carriers. For this, Stated Preference (SP) research has been performed for three variables, including fare, travel time and the number of runs, to estimate the substitution rate of each of the three variables. Binomial Logit Model has been estimated with the obtained data. The estimation of the model has found that airline passengers of major and low-cost carriers are willing to pay approximately 7,200 KRW and 5,000 KRW, respectively, to reduce travel time by one hour. If the number of runs in one day increases, it has been estimated that the passengers are willing to pay additional fares of about 390 KRW and 30 KRW, respectively. On the other hand, the substitution rate between the number of runs and the travel time was found to be somewhat insignificant. If the construction of the Seoul-Jeju line progresses in the future, this study could be used as preliminary data for determining fares, travel time and the number of runs.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.32 no.4 s.59
• /
• pp.269-282
• /
• 2006

In this study, we tried to scrutinize the status and problems of domestic cosmetics industry. On the basis of theoretical study, we examined the strategic marketing skill and tactics of foreign products to devise a strategy for domestic cosmetics with the help of marketing mix of foreign competitors: so to say 4 Ps. The core of the empirical research is hereby the effect of consumers' behavior. The conclusion of the research can be summarized as following: the most important problem of domestic cosmetics industry is the poor brand power. It has been confirmed that the consumer needs are various and dynamic. Analysis of 4 Ps of marketing factors of foreign goods shows this very clearly. Consumers tend to rely upon the brand name of the product rather than the quality, when they don't have enough information or knowledge on the product. This conclusion teaches us to make an effective strategy of marketing. It is brand power and brand cultivating. This study may give domestic marketers a motive to predict the future and succeed in existence and prosperity.

• Journal of Korean Association for Spatial Structures
• /
• v.7 no.1 s.23
• /
• pp.45-53
• /
• 2007

Recently, high-rise base isolated building structures with shear keys are often constructed in Japan which frequently occurs earthquakes. High-rise buildings are less damaged because those buildings have longer natural period than md or low rise buildings. The shear key is device that prevents the base isolators operating by the wind loads not by the earthquake loads. In case of big base shear force acts on the shear keys by earthquake, this device is broken and base isolator is operated. Therefore, seismic intensities play a role in acting on the shear keys. If wind loads are hither than the earthquake loads, the shear keys designed by wind loads are not operated in earthquakes. So, the requirements of shear keys in high-rise base isolated building structures must be examined in Korea with moderate seismic legions. In this study shear keys are applied with 5 and 15 stories base isolated building structures and investigated their dynamic responses to original and 1/2 scale downed El Centre NS(1940) ground motions. The results show that the yield shear forces of the shear keys affect significantly the dynamic behavior of base isolated building structures

• Journal of Hydrogen and New Energy
• /
• v.23 no.5
• /
• pp.513-520
• /
• 2012

The electrochemical reaction of refuse derived fuel (RDF) and refuse plastic/paper fuel (RPF) was investigated in the direct carbon fuel cell (DCFC) system. The open circuit voltage (OCV) of RPF was higher than RDF and other coals because of its thermal reactive characteristic under carbon dioxide. The thermal reactivity of fuels was investigated by thermogravimetric analysis method. and the reaction rate of RPF was higher than other fuels. The behavior of all sample's potential was analogous in the beginning region of electrochemical reactions due to similar functional groups on the surface of fuels analyzed by X-ray Photoelectron Spectroscopy experiments. The potential level of RDF and RPF decreased rapidly comparing to coals in the next of the electrochemical reaction because the surface area and pore volume investigated by nitrogen gas adsorption tests were smaller than coals. This characteristic signifies the contact surface between electrolyte and fuel is restricted. The potential of fuels was maintained to the high current density region over 40 $mA/cm^2$ by total carbon component. The maximum power density of RDF and RPF reached up to 45~70% comparing to coal. The obvious improvement of maximum power density by increasing operating temperature was observed in both refuse fuels.

• Journal of Sensor Science and Technology
• /
• v.10 no.1
• /
• pp.33-41
• /
• 2001

Wire ropes have been widely used in industrial applications, wherever heavy weight should be carried safely or mechanical energy should be transmitted fast. Especially, wire rope failures in operating elevator may lead to extensive property damage and serious injury to nearby personnel. Hence, it is very important to inspect wire rope periodically. Failure defection of wire rope requires fundamental knowledge of wire rope construction, rope behavior, properties of fault, sensing and signal processing method. In this research, the development of a new fault detecting system incorporating Hall-effect sensors to detect flaws such as abrasion, broken wire, corrosion and deformation for aged wire ropes in elevator, is described. For using a detector as a portable instrument, several performances for implementing sensing part with Hall-effect sensor, analog signal processing unit and programs are described. Experiments and field testing results for the implemented detecting system are also given. As a result, it is verified that the detecting system has good efficiency for inspecting faults of aged wire ropes in service.

• Journal of the Korean Society of Combustion
• /
• v.18 no.2
• /
• pp.32-41
• /
• 2013

This study presents both experimental and numerical investigation of ignition delay time of n-heptane and n-butanol binary fuel. The $O_2$ concentration in the mixture was set to 9-10% to make high exhaust gas recirculation( EGR) rate condition which leads low NOx and soot emission. Experiments were performed using a rapid compression machine(RCM) at compressed pressure 20bar, several compressed temperature and three equivalence ratios(0.4, 1.0, 1.5). In addition, a numerical study on the ignition delay time was performed using CHEMKIN codes to validate experimental results and predict chemical species in the combustion process. The results showed that the ignition delay time increased with increasing the n-butanol fraction due to a decrease of oxidation of n-heptane at the low temperature. Moreover, all of the binary fuel mixtures showed the combustion characteristics of n-heptane such as cool flame mode at low temperature and negative-temperature-coefficient(NTC) behavior. Due to the effect of high EGR rate condition, the operating region is reduced at lean condition and the ignition delay time sharply increased compared with no EGR condition.

• Journal of the Korean Society of Industry Convergence
• /
• v.23 no.4_2
• /
• pp.617-626
• /
• 2020

The drilling mud is essentially used in oil and gas development. There are several roles of using the drilling mud, such as cleaning the bottomhole, cooling and lubricating the drill bit and string, transporting the cuttings to the surface, keeping and adjusting the wellbore pressure, and preventing the collapse of the wellbore. The fragments from rocks and micro-sized bubbles generated by the high pressure are mixed in the drilling mud. The systems to separate those mixtures and to keep the uniformly maintained quality of drilling mud are required. In this study, the simulation is conducted to verify the performance of the mud tank's agitation capacity. The primary role of the mud tank is the mixing of mud at the surface with controlling the mud condition. The container type is chosen as a mud tank pursuing efficient transport and better management of equipment. The single- and two-phase simulations about the agitation in the mud tank are performed to analyze and identify the inner flow behavior. The convergence of results is obtained for the vertical- and axis-direction velocity vector fields based on the grid-dependency tests. The mixing time analysis depending on the multiphase flow conditions indicates that the utilization of a two-stepped impeller with a smaller size provides less time for mixing. This study's results are expected to be utilized as the preliminary data to develop the mixing and integrating equipment of the onshore drilling mud system.

• Korean Journal of Metals and Materials
• /
• v.48 no.1
• /
• pp.49-56
• /
• 2010

This study investigated how the surface of Al-12wt.%Si alloy modified by the plasma electrolytic oxidation process (PEO). The PEO process was performed in an electrolyte with sodium hexametaphsphate as a conducting salt, and the effect of ammonium metavanadate on variations in the morphology of electrochemically generated oxide layers on the alloy surface was investigated. It is difficult to form a uniform passive oxide layer on Al alloys with a high Si content due to the differences in the oxidation behavior of the silicon-rich phase and the aluminum-rich phase. The oxide layer covered the entire surface of the Al-12WT.%Si alloy uniformly when ammonium metavanadate was added to the electrolyte. The oxide layer was confirmed as a mixture of $V_2O_3$ and $V_2O_5$ by XPS analysis. In addition, the oxide layer obtained by the PEO process with ammonium metavanadate exhibited a black color. Application of this surface modification method is expected to solve the problem of the lack of uniformity in the coloring of oxide layeres caused by different oxidation behaviors during a surface treatment.

• Korean Journal of Metals and Materials
• /
• v.47 no.3
• /
• pp.175-181
• /
• 2009

Mechanical properties and precipitation behavior of backward extruded 6061 Al alloy for pressure vessel were investigated using tensile test, transmission electron microscopy (TEM) and differential scanning calorimeter (DSC). In this study, solution heat treatment (SHT) was performed at $535^{\circ}C$ for 30~90 min and aging treatment was conducted at 177 and $190^{\circ}C$ for 1~7 h. Maximum tensile strength of $36.6kgf/mm^2$ and yield strength of $33.29kgf/mm^2$ were achieved at the aging time of 5 h at $190^{\circ}C$. TEM observation showed that fine needle-like ${\beta}^{{\prime}{\prime}}$ phase which has 35~45 nm of length was uniformly distributed in the aged 6061 Al alloy specimen. From tensile test, TEM and DSC analysis, it is expected that aging time of 2~5 h at $190^{\circ}C$ is suitable for the extruded A6061 used as pressure vessels.