• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.623-626
• /
• 2005

In this paper, we proposed a new type SIR bandpass filter using DAML. This filter is consisted of 2 layers with MEMS resonator layer and CPW feed line. DAML ring resonator is elevated with $10\;{\mu}m$ height from GaAs substrate. Using MEMS processing, we are able to realize SIR bandpass filter easily. Furthermore it is useful to integrate on conventional MMICs because it has CPW interfaces and ring resonator is isolated from substrate by air-gap. We optimized and measured the results that $S_{21}$ attenuation at rejected band is over 15 dB, insertion loss is inside the limit of 3 dB, and relative bandwidth is about 10 % at 60 GHz

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.28 no.1
• /
• pp.49-60
• /
• 2017

In this paper, we presented the result of the study on high-power handling capability of the X-band circular waveguide cavity filter configured at the output of high power amplifier(120 W) for geostationary satellites. The dual mode circular waveguide cavity filter with 6th order is selected and the physical model of the filter is designed after determination of the size of resonator from mode chart. Multipactor margin analysis is performed by the SEM method and the VMF method. The result shows that the VMF method predicts lower multipactor breakdown thresholds than the SEM method. Evaluating the multipactor margin obtained by the VMF method to ECSS criteria, we could decide to perform multipactor test. The multipactor test conducted in ESA facility shows that multipactor did not occur even until the RF power increased up to 540 W. In consequence, by both analysis and test, we could verify that the X-band circular waveguide cavity filter has the sufficient high-power handling capability to operate on orbit.

• Korean Journal of Optics and Photonics
• /
• v.15 no.1
• /
• pp.17-21
• /
• 2004

We demonstrate an S/S＋band discretely tunable thulium doped fiber laser (TTDFL), anchored on a 50-㎓ ITU-T grid. Investigating the inversion analysis of the thulium doped fiber (TDF) in applying a dual wavelength (1.4 m and 1.5 m) pumping scheme, a laser whose tuning range covers most of the S/S＋band has been obtained. Within the wide 3-㏈ bandwidth of 65.1 nm, the output power of the tunable laser exceeds 6.1 ㏈m with very flat spectral profile and the number of DWDM channels generated is as large as 178. If we increase the subsidiary pump power to 22 ㎽, the bandwidth is expanded up to 66.2 nm. By controlling the temperature of the fine grid filter, we have also shown that the frequency locking capability of the laser can be improved. The laser developed in this work is expected to be utilized as a practical optical source providing reference wavelengths in the S/S＋band.

• Journal of Advanced Navigation Technology
• /
• v.10 no.1
• /
• pp.13-19
• /
• 2006

In this paper, Gaussian impulse generator for DS-UWB was proposed and fabricated so that the frequency band allocated to WLAN, around 5 GHz, was suppressed in accordance with the regulation of radiation spectrum limitation defined by FCC. In order to transform an unipolar rectangular signal to a Gaussian impulse, the proposed impulse generator consists of two stage impulse generation parts; the first stage using dual SRD and the second stage using gain switching of semiconductor laser diode. The result shows a gaussian impulse as narrow as 180 psec in width. In addition, high order derivative Gaussian filter with a structure of 4 stage ring resonators was designed and fabricated so that DS-UWB impulse generator could reduce the frequency spectrum of WLAN by 25 dB compared to the spectral power of th adjacent UWB band.

• Journal of electromagnetic engineering and science
• /
• v.18 no.3
• /
• pp.188-198
• /
• 2018

In this study, we propose an approach for the design and satisfy the requirements of the fabrication of a small, lightweight, reliable, and stable ultra-wideband receiver for millimeter-wave bands and the contents of the approach. In this paper, we designed and fabricated a stable receiver with having low noise figure, flat gain characteristics, and low noise characteristics, suitable for millimeter-wave bands. The method uses the chip-and-wire process for the assembly and operation of a bare MMIC device. In order to compensate for the mismatch between the components used in the receiver, an amplifier, mixer, multiplier, and filter suitable for wideband frequency characteristics were designed and applied to the receiver. To improve the low frequency and narrow bandwidth of existing products, mathematical modeling of the wideband receiver was performed and based on this spurious signals generated from complex local oscillation signals were designed so as not to affect the RF path. In the ultra-wideband receiver, the gain was between 22.2 dB and 28.5 dB at Band A (input frequency, 18-26 GHz) with a flatness of approximately 6.3 dB, while the gain was between 21.9 dB and 26.0 dB at Band B (input frequency, 26-40 GHz) with a flatness of approximately 4.1 dB. The measured value of the noise figure at Band A was 7.92 dB and the maximum value of noise figure, measured at Band B was 8.58 dB. The leakage signal of the local oscillator (LO) was -97.3 dBm and -90 dBm at the 33 GHz and 44 GHz path, respectively. Measurement was made at the 15 GHz IF output of band A (LO, 33 GHz) and the suppression characteristic obtained through the measurement was approximately 30 dBc.

• ETRI Journal
• /
• v.26 no.3
• /
• pp.229-240
• /
• 2004

This paper reports on our development of a dual-mode transceiver for a CMOS high-rate Bluetooth system-onchip solution. The transceiver includes most of the radio building blocks such as an active complex filter, a Gaussian frequency shift keying (GFSK) demodulator, a variable gain amplifier (VGA), a dc offset cancellation circuit, a quadrature local oscillator (LO) generator, and an RF front-end. It is designed for both the normal-rate Bluetooth with an instantaneous bit rate of 1 Mb/s and the high-rate Bluetooth of up to 12 Mb/s. The receiver employs a dualconversion combined with a baseband dual-path architecture for resolving many problems such as flicker noise, dc offset, and power consumption of the dual-mode system. The transceiver requires none of the external image-rejection and intermediate frequency (IF) channel filters by using an LO of 1.6 GHz and the fifth order onchip filters. The chip is fabricated on a $6.5-mm^{2}$ die using a standard $0.25-{\mu}m$ CMOS technology. Experimental results show an in-band image-rejection ratio of 40 dB, an IIP3 of -5 dBm, and a sensitivity of -77 dBm for the Bluetooth mode when the losses from the external components are compensated. It consumes 42 mA in receive ${\pi}/4-diffrential$ quadrature phase-shift keying $({\pi}/4-DQPSK)$ mode of 8 Mb/s, 35 mA in receive GFSK mode of 1 Mb/s, and 32 mA in transmit mode from a 2.5-V supply. These results indicate that the architecture and circuits are adaptable to the implementation of a low-cost, multi-mode, high-speed wireless personal area network.

• Korean Journal of Applied Biomechanics
• /
• v.13 no.2
• /
• pp.115-122
• /
• 2003

The purposes of this study were to analyze the muscle activities and the characteristics of muscle recruting patterns of lower limb for crouching start technique using four elite splint. The EMG technique was used to record muscle activities of both right and left sides of retus femoris, vastus medialis, biceps femoris, and gastrocnemius. Eight surface electrodes were placed on the surface of the selected muscles and one ground electrode was also attached on the back of neck(C7). One video camera was also used to record the crouching start motion to define 6 events and 5 phases for further analysis. The raw EMG data were filtered with band pass filter(10-350) to remove artifacts and then low pass filtered(4Hz) to find the linear envelope which resemble muscle tension curve. This filter EMG data were normalized to MVIC for the purpose of comparison between right and left sides muscle. The results of this study were as follows. All four subjects showed that vastus medialis muscle activity was comparatively higher than those of retus femoris, biceps femoris, gastrocnemius. And left side of muscle activity was comparatively higher than right side of muscle activity. Therefore, when the subjects starting out crouching start position, we recognized that the muscle of lower limb showed interaction effect by each muscle.

• Proceedings of the KIEE Conference
• /
• 2011.07a
• /
• pp.1660-1661
• /
• 2011

본 논문에서는 7중 대역 (GSM850, GSM900, DCS1800, PCS1900, UMTS850, UMTS1900, UMTS2100) 을 지원하는 LPF 내장형 LTCC 프런트 엔드 모듈 (FEM) 을 설계, 제작 및 측정하였다. 제작된 FEM은 효과적인 고조파 제거를 위해 수동소자를 LTCC 기판에 내장하여 저역 통과 필터(LPF)를 구현하였다. 본 논문에서 제안하는 FEM은 송수신 신호를 선택하기 위한 flip-chip 형태의 CMOS RF SP9T switch, Rx 신호의 수신을 위한 dual type의 SAW filter, 매칭 및 ESD 보호 회로를 위한 0603 크기의 칩소자가 부품 외부에 실장되어 구현된다. 전체 크기는 $4.5{\times}3.2{\times}1.2\;mm^3$의 초소형으로 내부 GND 2개 층을 포함하여 총 16층으로 구성된다. 측정결과는 송신단과 수신단의 삽입손실이 각각 1.7 dB, 3.6 dB 이하의 우수한 특성을 보였다.

• Proceedings of the KIEE Conference
• /
• 2009.07a
• /
• pp.1603_1604
• /
• 2009

본 논문에서는 SIR(Stepped Impedance Resonator)를 이용하여 RFID 주파수 대역의 이중대역 필터를 설계 연구하였다. 반파장 SIR을 parallel-coupled 형태로 설계하고 넓은 주파수 간격의 이중대역필터를 구현하기 위해서 2st 공진 주파수를 2.45GHz 대역에 맞추고 1st 공진 주파수를 억제하기 위해서 대역저지 필터를 결합하였다. 입출력에 대역 저지 필터를 구성하고 반파장 parallel-coulpled SIR은 미앤더 구조로 설계하여 크기를 줄였다. 본 논문에서 설계된 필터는 두 대역에서 -3.5~3.9dB의 삽입 손실을 가지며 433MHz에서 8MHz, 2.45GHz에서 21MHz의 대역폭을 나타낸다. 관심 주파수 이외의 대역에서는 -50dB 이상의 저지 특성을 가진다.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.4
• /
• pp.393-400
• /
• 2003

This paper deals with the design and manufacturing technique of EQM(Engineering Qualification Model) of input multiplexer(IMUX) for the Ku-band satellite transponder. Channel dropping method by circulator chain structure is adopted for demultiplexing each channel. External equalizers are attached behind channel filters fur reduction of group delay variation and amplitude variation simultaneously. Both channel filters and equalizers adopted dual-mode technique in design f3r mass and volume reduction. Channel filters are designed to have 8-pole elliptic response and equalizers to be of 2-pole reflection type. For good temperature stability characteristics, INVAR36 material is used for channel filters and external equalizers. Vibration test, Thermal Vacuum Test, and EMC test have been performed on input multiplexer and it is shown to be suitable for Ku-band satellite transponder.