• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.6
• /
• pp.437-445
• /
• 2021

This paper proposes an operating frequency design method that limits the voltage applied to aload-side converter during the initial operation of a loosely coupled resonant dual-active bridge (LCR-DAB) converter and an initial operating strategy that applies it. The LCR-DAB converter uses two wireless power transfer coils instead of the high-frequency transformer of the general DAB converter. The wireless power coil has a physical distance of several tens of millimeter or more between the two coils; thus, the LCR-DAB converter is a bidirectional isolated power conversion system that can easily achieve high insulation performance. However, for the initial operation of the LCR-DAB, if the power-side converter is operated at the resonance frequency while the load-side converter is not operating, then a very high voltage due to resonance is applied to the load-side converter, thereby causing damage to the converter. Therefore, a method that can stably charge the DC link voltage of the secondary-side converter during the initial operation is needed. This paper proposes a method to initially charge the secondary-side DC link by operating the primary-side converter at a frequency with limited voltage gain rather than at a steady-state operating frequency. The validity of the proposed frequency design method and initial operating sequence is verified through simulation and experimentation of the 1 KW LCR-DAB converter.

• Proceedings of the KIPE Conference
• /
• 2017.07a
• /
• pp.235-236
• /
• 2017

본 논문에서는 저압 직류 배전 시스템에 사용되는 3-레벨 NPC DAB 컨버터의 중성점 전압 제어를 위한 향상된 스위칭 알고리즘을 제안한다. 3-레벨 NPC DAB 컨버터는 구조상 정격전압 감소를 위해 중성점을 기준으로 DC-link 단에 두 개의 캐패시터가 사용되기 때문에 중성점으로 들어오는 전류에 불균형이 발생하며 중성점 전압이 흔들리는 문제점이 나타난다. 중성점 전압이 흔들릴 경우 불균형한 전압이 변압기에 형성되며 이로 인해 전류 Offset과 실효 전류의 증가에 따른 전력 손실증가 등 전체적인 컨버터의 동작에 악영향을 준다. 따라서 본 논문에서는 3-레벨 NPC DAB 컨버터의 동작원리 및 기존 스위칭 패턴을 분석하고, 향상된 스위칭 패턴을 적용시켜 중성점 전압을 제어하는 알고리즘의 타당성을 모의시험을 통해 검증하고자 한다.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.109-111
• /
• 2020

본 논문에서는 ESS용 전류원 Dual-Active-Bridge 컨버터의 저 부하 및 고 부하에서의 효율 향상을 위한 하이브리드 스위칭 알고리즘을 제안하고자 한다. 전류원 DAB 컨버터는 인터리브 구조를 이용하여 배터리 단의 입력 전류 리플을 저감할 수 있고, 전력 변환 효율 개선을 위한 다양한 제어 변수를 도입할 수 있는 등의 장점으로 인해 DC 마이크로그리드에서 ESS용 절연형 양방향 DC/DC 컨버터로 주목받고 있다. 그러나 전류원 DAB에서 종래의 전력 제어 방법인 펄스폭 변조 방식과 위상천이가 결합된 방법 (PWM plus Phase Shift, PPS)의 경우 저 부하 조건에서 높은 피크 전류로 인해 도통 손실이 크며, 펄스폭 변조 방식과 이중 위상천이가 결합된 방법(PWM plus Dual Phase Shift, PPDPS)의 경우 고 부하 조건에서 영전압 스위치 영역이 좁아져 효과적이지 않다. 따라서 본 논문에서는 2차 측의 펄스폭과 위상천이를 독립적으로 제어하는 하이브리드 스위칭 알고리즘을 통해 순환전류를 감소시키고 영전압 스위치 영역을 확장시켜 저 부하 및 고 부하 모두에서 효율을 향상시키고자 한다. 1-kW급 전류원 DAB 컨버터 시작품을 통해 제안된 하이브리드 스위칭 알고리즘의 효율성과 타당성을 검증한다.

• Journal of IKEEE
• /
• v.23 no.3
• /
• pp.994-1002
• /
• 2019

In this paper, we propose the development of a power conversion system for electric power take-off (e-PTO) of agricultural electric vehicles. Most e-PTOs use commercial power $220V_{AC}$. A bidirectional power conversion system having a two-stage structure consisting of a DC-DC converter and a DC-AC inverter for supplying a high output voltage using a low battery voltage of an agricultural electric vehicle is suitable. we propose a power conversion system consisting of the one-stage dual active bridge (DAB) converter and the two-stage bidirectional full bridge inverter. In addition, we propose a soft start algorithm for reducing the inrush current generated by the link capacitor charging during the initial operation. A 3kW prototype system and its corresponding algorithms have been implemented to verify its effectiveness through experiments.

• Journal of Power Electronics
• /
• v.18 no.2
• /
• pp.383-394
• /
• 2018

This paper presents an isolated power factor correction converter for general-purpose electric vehicle chargers with a wide output voltage range. The converter is based on an asymmetrical dual active bridge structure so that the voltage stress of switching devices can be eliminated by transferring the transformer leakage inductance to the circuit parameters. Harmonic and output controls are performed by secondary switches, and primary switches are only operated at a fixed frequency with a 50% duty ratio. A harmonic modulation technique is also adopted to obtain a near-unity power factor without input current monitoring. The feasibility of the proposed charger is verified with a 3.3 kW prototype.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.22 no.4
• /
• pp.336-344
• /
• 2017

This paper presents the three-port DC-DC converter modeling and controller design procedure, which is part of the solid-state transformer (SST) to interface medium voltage AC grid to bipolar DC distribution network. Due to the high primary side DC link voltage, the proposed converter employs the three-level neutral point clamped (NPC) topology at the primary side and 2-two level half bridge circuits for each DC distribution network. For the proposed converter particular structure, this paper conducts modeling the three winding transformer and the power transfer between each port. A decoupling method is adopted to simplify the power transfer model. The voltage controller design procedure is presented. In addition, the output current sharing controller is employed for current balancing between the parallel-connected secondary output ports. The proposed circuit and controller performance are verified by experimental results using a 30 kW prototype SST system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.5
• /
• pp.384-390
• /
• 2022

In this study, a single-stage, four-phase, interleaved, totem-pole AC-DC converter is proposed for a super-fast charger station that requires high power, a wide voltage range, and bidirectional operation capabilities and adopts various types of electric transport vehicles. The proposed topology is based on current-fed push-pull dual active bridge converter combined with the totem-pole operation. Owing to the four-phase interleaving effect, the bridge on the grid side can switch at 0.25, 0.5, and 0.75 to achieve a ripple-free grid current. The input filter can be removed theoretically. Switching methods for the duty of the secondary-side duty cycle are proposed, and they correspond to the primary duty cycle for reducing the circulating power and handling the total harmonic distortion. Therefore, the converter can operate under a wide voltage range. Experimental results from a 7.5 kW prototype are used to validate the proposed concept.

• Proceedings of the KIPE Conference
• /
• 2020.08a
• /
• pp.385-386
• /
• 2020

최근, 에너지저장장치를 활용하여 태양광-ESS 하이브리드 시스템이 도입되고 있다. 태양광-ESS 하이브리드 시스템은 구성방식에 따라 다양한 전력변환장치를 활용한다. 그중 DAB 컨버터는 절연형이며, 양방향 전력전달이 가능하므로 스위칭 기법, 토폴로지 개발 등 연구가 활발히 진행되고 있다. 본 논문에서는 태양광-ESS 하이브리드 시스템에 적용되는 대표적인 벅-부스트 컨버터와 DAB 컨버터에 대해 리뷰한다.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.6
• /
• pp.507-514
• /
• 2022

This study proposes an optimal design process for a high-frequency transformer that has a large leakage inductance for dual-active-bridge converters. Notably, conventional design processes have large errors in designing leakage transformers because mathematically modeling the leakage inductance of such transformers is difficult. In this work, the geometric parameters of a shell-type transformer are identified, and finite element analysis(FEA) simulation is performed to determine the magnetization inductance, leakage inductance, and copper loss of various shapes of shell-type transformers. Regression models for magnetization and leakage inductances and copper loss are established using the simulation results and the machine learning technique. In addition, to improve the regression models' performance, the regression models are tuned by adding featured parameters that consider the physical characteristics of the transformer. With the regression models, optimal high-frequency transformer designs and the Pareto front (in terms of volume and loss) are determined using NSGA-II. In the Pareto front, a desirable optimal design is selected and verified by FEA simulation and experimentation. The simulated and measured leakage inductances of the selected design match well, and this result shows the validity of the proposed design process.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.27 no.6
• /
• pp.498-506
• /
• 2022

This study proposes a design methodology for bidirectional, series-resonant, dual-active bridge (SRDAB) converters. The circuit parameters of the SRDAB converters are designed by considering the output power and efficiency of the converter. The proposed method can be used to design a high-power, high-efficiency SRDAB converter. A voltage controller is employed to manipulate the output voltage of the converter, and the controller gains are selected using the transfer function and frequency response of the controller. Simulation results show that the output power of the designed SRDAB converter is 2 kW per converter module as designed. In addition, the performance of the voltage controller is evaluated using the simulation and experimental results. The output voltage follows the reference voltage within 10 ms under the step change of the reference command. The output voltage also follows the reference voltage under the step load change. The efficiency of the designed SRDAB converter is 95.6%.