• 전력전자학회논문지
• /
• 제17권2호
• /
• pp.142-149
• /
• 2012

The independently regulated dual-output LLC resonant converter using only one power stage and one control IC is proposed in this paper. The conventional dual-output LLC resonant converter requires the extra non-isolated DC/DC converter to obtain the tightly regulated slave output voltage, which results in the low power conversion efficiency and high production costs. On the other hand, since the proposed converter controls the master and slave output voltages by pulse width modulation(PWM) and pulse frequency modulation(PFM), it can achieve tightly regulated dual output voltages without the additional non-isolated DC/DC converter. Therefore, it features a high efficiency and low cost. To confirm the validity of the proposed converter, theoretical analysis and experimental results from a 40W LED driver prototype are presented.

• 전기전자학회논문지
• /
• 제18권2호
• /
• pp.220-227
• /
• 2014

이 논문은 Dead-time을 갖는 톱니파 발생기를 이용하여 공통모드와 차동모드 피드백 루프를 구현한 Single-Inductor Dual-Output DC-DC Converter 설계에 관한 내용을 제시하고 있다. 제어회로에는 공통모드와 차동모드 피드백 루프를 Dead-time을 갖는 톱니파 발생기를 이용하여 동시에 사용하였다. 차동모드 피드백 루프에서 duty를 생성하기 위해서 전류 분배기 회로를 사용하여 공통모드 피드백에 의한 duty에 따라 dead-time이 유동적으로 변하는 톱니파형을 만드는 회로인 Dead-time을 갖는 톱니파 발생기를 추가하여 차동모드 피드백 회로를 구성하였다. 0.35um 공정을 사용하여 설계한 SIDO DC-DC Converter는 2.5V 입력으로부터 2.8V와 4.2V의 전압을 출력하며 최대 전력변환 효율은 95%이다. 출력간의 Cross regulation은 출력전류가 2배씩 증가할 경우 Boost1과 Boost2의 출력전압은 각각 3.57%, 4% 수준을 보이고 있다.

• Journal of Power Electronics
• /
• 제14권6호
• /
• pp.1217-1223
• /
• 2014

A novel half load-cycle worked dual input single output (DISO) DC/AC inverter is presented. The basic circuit consists of a dual buck regulator, which works in continuous current mode. The working principle of DISO DC/AC inverter has been used. The control method applied for half load-cycle worked DISO DC/AC inverter has been studied. The control effects of the open-loop proportional control and closed-loop proportional-integral control are compared by using PSIM software. The parameters are adopted in the realistic simulation and experiment test. Moreover, the waveforms, such as voltage of modulation reference signal and output voltage, were given. The simulation and experiment results proved that the half load-cycle worked DISO DC/AC inverter could achieve good performance, gain a line frequency of 50 Hz, and verify the correctness of theoretical analysis.

• Journal of Power Electronics
• /
• 제2권4호
• /
• pp.312-324
• /
• 2002

This paper presents a new PWM DC/DC converter with dual output power using single power stage, which has the isolation characteristics between each dual output. The proposed converter topology consists of two switches ($S_B$ and $S_F$) and only single secondary winding. Therefore, the proposed converter has better advantages of not only low cost and small size but also high power density because of using minimum components and devices compared with conventional methods which use multi winding transformers or several converters. The operating principle of the proposed converter topology, which includes the conventional auxiliary ZVT (Zero-Voltage-Transition) circuit to implement soft switching of the main switch, is illustrated in detail and the validity of the proposed converter is verified through several simulated and experimental results.

• 전기학회논문지P
• /
• 제54권4호
• /
• pp.171-178
• /
• 2005

The proposed dual-output DC-DC converter that bases on flyback converter can obtain two output voltage with non-isolated main-output and isolated sub-output at the same time using single-winding high frequency transformer. It can solve problems in multi-winding converter that use one main-switch, and also control quality of isolated sub-output voltage can be improved by additional sub-switch to the second. For analysis and design of the proposed converter system, converters are classified as operation mode from switching state and are become modeling by applying state space averaging method. Steady-state characteristics and dynamic characteristics are analyzed by DC component and perturbation component from state space averaging model. From experiment converter, validity of analysis and design for the propose converter system is confirm.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2002년도 ICCAS
• /
• pp.74.4-74
• /
• 2002

$\textbullet$ Introduction $\textbullet$ Circuit modified $\textbullet$ Implement of the dual output converter $\textbullet$ Conclusions

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.237-242
• /
• 2000

The areal recording density of HDD(Hard Disk Drive) has been increasing by about 60% a year. In order to achieve high areal density, less track pitch is expected and more servo bandwidth is required. Dual stage actuator and servo controller for HDD have been suggested for achieving high track density as a possible solution. Dual-loop servo system is generally classified into a two-input-two-output system, but if we use an estimator for a two-input-two-output system, it can be converted into two input one output system. Since we can't control the dual stage servo system by the classical method, it requires a special technique; for example, Parallel Loop System, Master-Slave Loop System, Decoupled Master-Slave Loop System, and Dual Feedback Loop System. In this paper, we performed experimental evaluations of several types of control algorithm. Further experiments will be made in the future.

• 조명전기설비학회논문지
• /
• 제28권4호
• /
• pp.80-87
• /
• 2014

This paper suggests the dual-gap for generating power and increasing the torque of a direct-drive permanent magnet synchronous motor in a hybrid-cycle. To consider easy coil winding, we applied a structure of dual-gap for the permanent magnet synchronous motor (PMSM). Because the torque of PMSM with the dual-gap is very large, we are designed the appropriate specifications of the PMSM by selected the appropriate dual-gap slot and poles combination. The prototype model is selected by design theory for increasing torque and maximizing output power of PMSM. And the detailed structure design of the model was designed by the loading distribution method. The PMSM models were analyzed by finite element method. Finally, we have suggested appropriate rotor structure has benefit to further increasing torque and prevent decreasing of the output power in PMSM with dual-gap.

• 한국전자파학회논문지
• /
• 제15권8호
• /
• pp.788-793
• /
• 2004

본 논문은 각각 1 W 출력의 5.8 GHz 대역의 무선 랜과 이동통신 서비스 주파수 대역인 1.8 GHz 대역에서 동작하는 이중대역 전력증폭기를 설계 및 제작하였다. 전력증폭기의 입력으로 다중대역 신호가 선택적으로 입력되지 않고 동시에 입력되어질 경우 효과적인 구조로 설계하였다. 입력 단에서 두 신호를 분리하기 위하여 PBG를 이용하여 광대역의 저지 특성을 가지는 Diplexer를 사용하였으며, 전력증폭기의 정합에는 Load-pull 이론을 적용하여 최대 출력을 얻도록 하였다. 전력증폭기의 선형성을 증가시키기 위하여 PBG 구조를 적용하였다. 본 논문은 Load-pull정합부 내에 PBG구조를 삽입하여 전력증폭기가 최대 출력 상태에서 선형성을 개선시켰다. 또한 출력 정합부내에서 PBG 구조의 위치에 따른 선형성 개선의 변화 시뮬레이션을 통해서 검증하였다.

• 조명전기설비학회논문지
• /
• 제27권7호
• /
• pp.67-75
• /
• 2013

In this paper, parallel input/serial output dual converter is designed appropriately for fuel cell hybrid power system. In case of proposed converter, zero voltage switching condition is designed without additional resonance device using leakage inductance of transformer and output capacitance of switch, and zero voltage switching method is used. Also, the system method is for increasing power by connecting half-bridge in parallel and increasing output voltage by connecting secondary output of transformer in serial. Through this method we can increase power and decrease volume of system. So in this paper, dual converter is designed. 1.5kW fuel cell hybrid power system was implemented, and system operation and stability was verified through experiment.