• Proceedings of the KIPE Conference
• /
• 2001.07a
• /
• pp.189-192
• /
• 2001

A new phase-shifted parallel-input/series-output dual converter for high-power step-up applications has been proposed. It features a high efficiency due to the low switch turn-off voltage, low device stresses, low ripple contents, and a fast control-to-output dynamics compared to its PWM counterpart. To confirm the validity of the proposed converter, experimental results from an 800W, 350Vdc prototype are presented.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.12 no.4
• /
• pp.1458-1470
• /
• 2018

In this letter, a new dual-port Multiple-Input Multiple-Output (MIMO) antenna is introduced which has two independent signal feeding ports in a single antenna element to achieve smaller antenna volumes for the 5G mobile applications. The dual-port structure is implemented by adding a cross coupled semi-loop (CCSL) antenna as the secondary radiator to the ground short of inverted-F antenna (IFA). It is found that the port to port isolation is not deteriorated when an IFA and CCSL is combined to form a dual-port structure. The isolation property of the proposed antenna is compared with a polarization diversity based dual-port antenna proposed in the literature [9]. The operating frequency range is 3.3-4.0 GHz which is suitable for places where $4{\times}4$ MIMO systems are supposed to be deployed such as in China, EU, Korea and Japan at the band ${\times}$ (3.3 - 3.8GHz. The measured 6-dB impedance bandwidths of the proposed antennas are larger than 700 MHz with isolation between the feeding ports higher than 18 dB [1-2]. The simulation and measurement results show that the proposed antenna concept is a very promising alternative for 5G mobile applications.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.9-15
• /
• 2011

In this paper, we designed and fabricated a dual-band bandpass filter which can control upper and lower bandwidth using the transformed E-shaped dual-mode resonator. The filter is made the coupling between even-mode not to affect odd-mode resonant frequency by the transformed resonator to control upper bandwidth effectively. The cross coupling between input and output feed lines was employed to improve stopband characteristic. The bandpass filter has been designed to indicate the same bandwidth at center frequency 2 GHz and 3 GHz to show to control bandwidth.

• Proceedings of the KIEE Conference
• /
• 2000.07d
• /
• pp.3166-3168
• /
• 2000

This paper proposed variable threshold dual rate ADPCM coding method which is modified from the standard ADPCM of ITU G.726 for speech quality improvement. The speech quality of variable threshold dual rate ADPCM is better than single rate ADPCM at noisy environment without increasing the complexity by using ZCR(Zero Crossing Rate). In this case, ZCR is used to divide input signal samples into two categories(noisy & speech). The samples with higher ZCR is categorized as the noisy region and the samples with lower ZCR is categorized as the speech region. Noisy region uses higher threshold value to be compressed by 16Kbps for reduced bit rates and the speech region uses lower threshold value to be compressed by 40Kbps for improved speech quality. Comparing with the conventional ADPCM, which adapts the fixed coding rate. the proposed variable threshold dual rate ADPCM coding method improves noise character without increasing the bit rate. For real time applications, ZCR calculation was considered as a simple method to obtain the background noise information for preprocess of speech analysis such as FFT and the experiment showed that the simple calculation of ZCR can be used without complexity increase. Dual rate ADPCM can decrease the amount of transferred data efficiently without increasing complexity nor reducing speech quality. Therefore result of this paper can be applied for real-time speech application such as the internet phone or VoIP.

• Journal of the Korean Institute of Telematics and Electronics B
• /
• v.32B no.6
• /
• pp.899-908
• /
• 1995

In this paper, the probabilistic relations of dual morphological operations, such as dilation and erosion, closing and opening, and close- open and open-close, and the statistical properties for a continuous stationary lst order Gauss-Markov source are analyzed. The result is that the dual filters have symmetrical means and skews, and equal variances. Also, the statistics of morphological filters are very similar with those of input source, as correlation coefficient increases.

• Proceedings of the KIPE Conference
• /
• 2001.10a
• /
• pp.708-712
• /
• 2001

A new phase-shifted parallel-input/series-output (PI SO) dual inductor-fed push-pull converter for high-power step­up applications is proposed. This converter is operated at a constant duty cycle and employs an auxiliary circuit to control the output voltage with a phase-shift between the two modules. It features a voltage conversion characteristic which is linear to changes in the control input, and high step-up ratio with a greatly reduced switch turn-off stress resulting in a significant increase in the converter efficiency. It also shows a low ripple content and low root-mean-square (RMS) current in the output capacitor. The operational principle is analyzed and a comparative analysis with the conventional pulse-width-modulated (PWM) PISO dual inductor-fed push-pull converter is presented. A 50kHz, 800W, 350Vdc prototype with an input of 20-32Vdc has also been constructed to validate the proposed converter. The proposed converter compares favorably with the conventional counterpart and is considered well suited to high-power step-up applications.

• Journal of Welding and Joining
• /
• v.29 no.5
• /
• pp.99-105
• /
• 2011

In this study, effect of Si content on nugget diameter in electric resistance spot welded dual-phase(DP) steel was investigated. The cold rolled DP steels with different Si content (0.5, 1.0, 1.5, 2.0 wt.%) were used and thickness of those sheet was 1.2mm. With increasing Si content, nugget diameter was increased at the same welding current. This is attributed to increase of heat input result from high resistivity. Also, nugget diameter was increased with an increase in Si content for the same heat input. For this reason, the melting point of DP steel is lowered with an increase in the Si content. And solid DP steel can easily be transformed to a liquid phase because the low melting point. Finally, a prediction formula for the nugget diameter(N.D.) could be obtained in terms of heat input(Q) and melting point(M.P) as follows: N.D.(mm) = 0.11Q(J) - 0.0031 M.P.($^{\circ}C$) + 0.32.

• International Journal of CAD/CAM
• /
• v.11 no.1
• /
• pp.18-26
• /
• 2011

This paper proposes a new solid-shape modeling system based on a lusterware-image illustration. The proposed method reconstructs a three dimensional solid shape from a set of rough sketches that are typically drawn in the early stages of the design process. The sketches do not have to be strictly accurate, and this tolerance to the roughness of the input sketches is one of the major advantages of the proposed method. The proposed system creates an initial shape based on the silhouette of the input lusterware-images. Then the user can edit the initial shape with intuitive cutting and dishing-up operations, which are based on sketching user interface. To achieve the goal, the system retains the geometric model with two representations: a point-set data and a volume data. This dual data structure allows the program to create an initial shape from the input images with little computational cost, and the user can apply cutting and dishing-up operations without substantially increasing computational and memory requirements. In this research, we have tested the proposed system by reconstructing solid models of some mechanical parts from rough sketches. The experimental results indicate that the proposed method is useful for the prototyping of a solid shape.

• Journal of Power Electronics
• /
• v.17 no.6
• /
• pp.1433-1444
• /
• 2017

A family of non-isolated DC-DC three-port converters (TPCs) that allows for a more flexible power flow among a renewable energy source, an energy storage device and a current-reversible DC bus is introduced. Most of the reported non-isolated topologies in this area consider only a power consuming load. However, for applications such as hybrid-electric vehicle braking systems and DC microgrids, the load power generating capability should also be considered. The proposed three-port family consists of one unidirectional port and two bi-directional ports. Hence, they are well-suited for photovoltaic (PV)-battery-DC bus systems from the power flow viewpoint. Three-port converters are derived by combining different commonly known power converters in an integrated manner while considering the voltage polarity, voltage levels among the ports and the overall voltage conversion ratio. The derived converter topologies are able to allow for seven different modes of operation among the sources and load. A three-port converter which integrates a boost converter with a buck converter is used as a design example. Extensions of these topologies by combining the soft-switching technique with the proposed design example are also presented. Experiment results are given to verify the proposed three-port converter family and its analysis.

• Aerospace Engineering and Technology
• /
• v.4 no.2
• /
• pp.21-26
• /
• 2005

In airframe structural tests, a control system which has many control channels and a data acquisition system which has many data acquisition channels are used. The more it is used many channels in airframe structural test, the more hardware resources are added in test system. Before test load is applied in test article, test engineer must check test system and components. Therefore, many problems which be likely to happen to system can be minimized. The checking method of test system and components is calibration verification. In this paper, it is described that calibration verification concept and method in relation to airframe structural test controller components.(MTS Aero90 Multifunction Input Output Processor and 497.22 Dual DC Conditioner)