• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.16 no.2
• /
• pp.952-962
• /
• 2015

In this study, multilayered rings with a large outer diameter have been developed using a hot ring rolling process. The ring rolling process has been analyzed by rigid plastic finite element analyses (FEA) using the AFDEX2D and AFDEX3D/HEXA/RING simulators, where the finite element meshes received severe plastic deformation are remeshed into a fine mesh-size using a dual-mesh system. According to the simulated results, the design variables of the multilayered rings were determined and real tests were conducted to check the validity of the simulation results. By adopting the hot ring rolling process, the input weight of raw materials was reduced by 40% against the conventional hot forging process and that the recovery rate was increased by 24%. The measurement of the averaged roundness was satisfied within 0.5 mm for both the inner and outer diameters. Moreover, the hot ring rolling processes yielded 1.49 Cpk for the outer-diameter and 0.84 Cpk 0.84 for the inner-diameter.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.24 no.6
• /
• pp.610-618
• /
• 2021

In this paper, a photonic-based microwave system technology is described, and a traveling-wave electro-optic modulator is designed and manufactured as a key component. The fabricated modulator is composed of a metal diffusion waveguide for optical transmission and a planar waveguide electrode on lithium niobate substrate for microwave transmission. The electro-optic response bandwidth of I and Q channels in a fabricated dual parallel Mach-Zehnder modulator were measured for 27.67 and 28.11 GHz, respectively. Photonic four times up-converted X-band frequency and linear frequency modulated signal were confirmed using the fabricated electro-optic modulator by S-band input signal. The confirmed broadband signal can be applied to a microwave system for surveillance and high-resolution ISAR imaging.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.26 no.6
• /
• pp.404-410
• /
• 2021

This paper proposes a high step-up converter with zero-voltage transition (ZVT) cell for fuel cell electric vehicle. The proposed converter applies a ZVT cell to a dual floating output boost converter (DFOBC) so that not only the main switch but also the ZVT switch can achieve full-range soft switching. The current rating of the ZVT switch is 17% of the main switch. The proposed converter has high reliability in that no timing issue occurs. Therefore, online calculation is not required. The minimum turn-on time of the ZVT switch that guarantees soft switching at all loads and input/output voltage is obtained by analysis. In addition, the proposed DFOBC allows the use of a 650 V device even at 800 V output and has the advantage of being able to boost the voltage by 3.5 times with 0.56 duty. Planar coupled inductor with PCB winding was successfully implemented with the converter operated at 300 kHz. The 25 kW prototype achieves peak efficiency of 99% and power density of 63 kW/L.

• KSII Transactions on Internet and Information Systems (TIIS)
• /
• v.16 no.1
• /
• pp.1-15
• /
• 2022

The MobileNetV3 is specially designed for mobile devices with limited memory and computing power. To reduce the network parameters and improve the network inference speed, a new lightweight network is proposed based on MobileNetV3. Firstly, to reduce the computation of residual blocks, a partial residual structure is designed by dividing the input feature maps into two parts. The designed partial residual structure is used to replace the residual block in MobileNetV3. Secondly, a dual-path feature extraction structure is designed to further reduce the computation of MobileNetV3. Different convolution kernel sizes are used in the two paths to extract feature maps with different sizes. Besides, a transition layer is also designed for fusing features to reduce the influence of the new structure on accuracy. The CIFAR-100 dataset and Image Net dataset are used to test the performance of the proposed partial residual structure. The ResNet based on the proposed partial residual structure has smaller parameters and FLOPs than the original ResNet. The performance of improved MobileNetV3 is tested on CIFAR-10, CIFAR-100 and ImageNet image classification task dataset. Comparing MobileNetV3, GhostNet and MobileNetV2, the improved MobileNetV3 has smaller parameters and FLOPs. Besides, the improved MobileNetV3 is also tested on CPU and Raspberry Pi. It is faster than other networks

• Journal of IKEEE
• /
• v.27 no.4
• /
• pp.494-500
• /
• 2023

Image processing is currently used in various fields. Among them, autonomous vehicles, medical image processing, and robot control require fast image processing response speeds. To fulfill this requirement, hardware design for real-time processing is being actively researched. In addition to the size of the input image, the hardware processing speed is affected by the size of the inactive video periods that separate lines and frames in the image. In this paper, we design three different scaler structures based on the type of line memories, which is closely related to the inactive video periods. The structures are designed in hardware using the Verilog standard language, and synthesized into logic circuits in a field programmable gate array environment using Xilinx Vivado 2023.1. The synthesized results are used for frame rate analysis while comparing standard image sizes that can be processed in real time.

• Journal of radiological science and technology
• /
• v.29 no.4
• /
• pp.229-236
• /
• 2006

Purpose: This study was conducted to search for the type of technical error in DEXA(dual-energy X-ray absorptiometry) and the effect of error to measurement of BMD. Materials and Methods: The changes of BMD($g/cm^2$, T-score) by patients information(Age, Weight, Height, Manopause age) input error and Confirming ROI error were investigated. Using spine phantom, we canned 10 times by age(5, 10), weight(10, 20 kg), height(5, 10 cm), manopause age(5, 10) increase & decrease respectively. Scanning region(L-spine, femur, Forearm) of 10 patients was calculated by changing ROI respectively. Analysis of difference for mean(precision 1%) were carried out. Results: The error of patient information(Age, Weight, Height, Manopause age) was not changed differently. In confirming ROI, the BMD and T-score of L-spine involving T-12 was decreased to $0.063\;g/cm^2$, 0.3 and involving L-5 increased to $0.077\;g/cm^2$, 0.5. In narrowing 1 cm of vertical line of ROI, the BMD and T-score decreased to $0.006\;g/cm^2$, 0.1 and in 2 cm, $0.021\;g/cm^2$, 0.15, each. In hip ROI, Upper and left shift(0.5 cm) of line was not influenced BMD and T-score. In 0.5 cm lower shift(lesser trochanter below), the BMD and T-score increased $0.031\;g/cm^2$, 0.3 and in 1 cm $0.094\;g/cm^2$, 0.65, each. In forearm ROI, the BMD and T-score decreased $0.042\;g/cm^2$, 0.9 involving 1 cm lower wrist. And expanding 1 cm of vertical line, the BMD and T-score decreased $0.008\;g/cm^2$, 0.1 and in 2 cm, $0.021\;g/cm^2$, 0.3, each. The L-spine, hip, forearm ROI error was changed differently. Conclusion: There are so many kinds of technical error in BMD processing. Errors according to age, weight, height, manopause age did not influent to $BMD(g/cm^2)$ and T-score. There are mean differences BMD and T-score in confirming ROI. For the precision exam, in L-spine processing, L1-4 have to confirmed without shift of ROI vertical line. In hip processing, the ROI have to included greater trochanter, femur head and lesser trochanter. In forearm processing, the ROI have to included wrist, radius and ulnar.

• Journal of Korea Water Resources Association
• /
• v.49 no.12
• /
• pp.981-993
• /
• 2016

This study explains the GIS database of flood inundation area developed for Samsung-1 Drainage Sector, Seoul, Korea. The XP-SWMM dual drainage model was developed for the study area, and the time series observed at the watershed outlet was used to obtain the watershed time of concentration and to calibrate the XP-SWMM model. The rainfall scenario was developed by dividing the 40 minute watershed time of concentration into two 20-minute time steps and then applying the gradually increasing 5 mm/hr interval rainfall intensity to each of the time step up to 200 mm/hr, which is the probable maximum precipitation of the study area. The developed rainfall scenarios was used as the input of the XP-SWMM model to obtain the database of the flood inundation area. The analysis on the developed GIS database revealed that: (1) For the same increment of the rainfall, the increase of the flooded area can be different, and this was caused by topographic characteristics and spatial formation of pipe network of the study area; (2) For the same flooded area, the spatial extent can be significantly different depending on the temporal distribution of rainfall; and (3) For the same amount of the design rainfall, the flood inundation area and the extent can be significantly different depending on the temporal distribution of rainfall.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2011.05a
• /
• pp.15-15
• /
• 2011

The radar observation system in Japan is operated by two governmental groups: Japan Meteorological Agency (JMA) and the Ministry of Land, Infrastructure, Transport and Tourism (MLIT) of Japan. The JMA radar observation network is comprised of 20 C-band radars (with a wavelength of 5.6 cm), which cover most of the Japan Islands and observe rainfall intensity and distribution. And the MLIT's radar observation system is composed of 26 C-band radars throughout Japan. The observed radar echo from each radar unit is first modified, and then sent to the National Bureau of Synthesis Process within the MLIT. Through several steps for homogenizing observation accuracy, including distance and elevation correction, synthesized rainfall intensity maps for the entire nation of Japan are generated every 5 minutes. The MLIT has recently launched a new radar observation network system designed for flash flood observation and forecasting in small river basins within urban areas. It is called the X-band multi parameter radar network, and is distinguished by its dual polarimetric wave pulses of short length (3cm). Attenuation problems resulting from the short wave length of radar echo are strengthened by polarimetric wavelengths and very dense radar networks. Currently, the network is established within four areas. Each area is observed using 3-4 X-band radars with very fine resolution in spatial (250 m) and temporal (1 minute intervals). This study provides a series of utilization procedures for the new input data into a real-time forecasting system. First of all, the accuracy of the X-band radar observation was determined by comparing its results with the rainfall intensities as observed by ground gauge stations. It was also compared with conventional C-band radar observation. The rainfall information from the new radar network was then provided to a distributed hydrologic model to simulate river discharges. The simulated river discharges were evaluated again using the observed river discharge to estimate the applicability of the new observation network in the context of operations regarding flood forecasting. It was able to determine that the newly equipped X-band polarimetric radar network shows somewhat improved observation accuracy compared to conventional C-band radar observation. However, it has a tendency to underestimate the rainfall, and the accuracy is not always superior to that of the C-band radar. The accuracy evaluation of the X-band radar observation in this study was conducted using only limited rainfall events, and more cases should be examined for developing a broader understanding of the general behavior of the X-band radar and for improving observation accuracy.

• Korean Journal of Comparative Education
• /
• v.27 no.1
• /
• pp.247-284
• /
• 2017

The purpose of this study is to analyze firm's motivation of participating and investing in apprenticeship in Germany and Korea, and to investigate institutional factors influencing firm's motivation. By comparing institutional factors of the two countries, it aims to drawing out policy implications for improving Korean apprenticeship. The main method for data collection was comprehensive literature review on international organizations, each countries' government and research institutes' policy materials, statistical data, research outputs and media resources related to each countries' apprenticeship. Considering whether firm's motivation for participating and investing in apprenticeship is production-oriented or investment-oriented, Germany is more inclined to investment motivation with firm's covering net cost during apprenticeship period. On the other hand, Korea is more inclined toward production orientation with firm's expectation of gaining net profit during the training period. Why is firm's training motivation different in these two countries? The author tried to find the reason from the difference of institutional factors of the countries by dividing institutional factors into 4 categories: context(tripartite relations, legal framework), input (flexibility of the system, government incentive), process(training contents, training duration, quality assurance), and output(completion/retention rate, apprentice's productivity). The key implication from the comparative analysis of institutional factors is that it is necessary to enforce companies to have "accountability" on the minimum critical elements, but also to ensure them to have "autonomy" on the rest of the elements.

• The Korean Journal of Archival Studies
• /
• no.10
• /
• pp.276-322
• /
• 2004

Historical interest in China in 1930s has been mostly focused on political characteristic of the National Government(國民政府) which was established by the KMT(中國國民黨) as a result of national unification. It is certain that China had a chance to construct a modern country by the establishment of the very unified revolutionary government. But, it was the time of expanding national crises that threatened the existence of the country such as the Manchurian Incident and the Chinese-Japanese War as well as the chaos of the domestic situation, too. So it has a good reason to examine the characteristic and pattern of the response of the political powers of those days. But, as shown in the recent studies, the manifestation method of political power by the revolutionary regime catches our attention through the understanding of internal operating system. Though this writing started from the fact that the Nationalist Government executed the administrative reform which aimed at "administrative efficiency" in the middle of 1930s, but it put stress on the seriousness of the problem and its solution rather than political background or results. "Committee on Administrative Efficiency(行政效率委員會)", the center of administrative reform movement which was established in 1934, examined the plan to execute the reform through legislation by the Executive Council(行政院) on the basis of the results of relevant studies. They claimed that the construction of a modern country should be performed by not political revolution anymore but by gradual improvement and daily reform, and that the operation of the government should become modern, scientific and efficient. There were many fields of administrative reform subjects, but especially, the field of records and archives adminstration(文書檔案行政) was studied intensively from the initial stage because that subject had already been discussed intensively. They recognized that records and archives were the basic tool of work performance and general activity but an inefficient field in spite of many input staff members, and most of all, archival reform bring about less conflicts than the fields of finance, organization and personnel. When it comes to the field of records adminstration, the key subjects that records should be written simply, the process of record treatment should be clear and the delay of that should be prevented were already presented in a records administrative meeting in 1922. That is, the unified law about record management was not established, so each government organization followed a conventional custom or performed independent improvement. It was through the other records administrative workshop of the Nationalist Government in 1933 when the new trend was appeared as the unified system improvement. They decided to unify the format of official records, to use marker and section, to unify the registration of receipt records and dispatch records and to strengthen the examination of records treatment. But, the method of records treatment was not unified yet, so the key point of records administrative reform was to establish a unified and standard record management system for preventing repetition by simplifying the treatment procedure and for intensive treatment by exclusive organizations. From the foundation of the Republic of China to 1930s, there was not big change in the field of archives administration, and archives management methods were prescribed differently even in the same section as well as same department. Therefore, the point at issue was to centralize scattered management systems that were performed in each section, to establish unified standard about filing and retention period allowance and to improve searching system through classification and proper number allowance. Especially, the problem was that each number system and classification system bring about different result due to dual operation of record registration and archives registration, and that strict management through mutual contrast, searching and application are impossible. Besides, various problems such as filing tools, arrangement method, preservation facilities & equipment, lending service and use method were raised also. In the process this study for the system improvement of records and archives management, they recognized that records and archives are the identical thing and reached to create a successive management method of records and archives called "Records and Archives Chain Management Method(文書檔案連鎖法)" as a potential alternative. Several principles that records and archives management should be performed unitedly in each organization by the general record recipient section and the general archives section under the principle of task centralization, a consistent classification system should be used by classification method decided in advance according to organizational constitution and work functions and an identical number system should be used in the process of record management stage and archive management stage by using a card-type register were established. Though, this "Records and Archives Chain Management Method" was developed to the stage of test application in several organizations, but it was not adopted as a regular system and discontinued. That was because the administrative reform of the Nationalist Government was discontinued by the outbreak of the Chinese-Japanese War. Even though the administrative reform in the middle of 1930s didn't produce practical results but merely an experimentation, it was verified that the reform against tradition and custom conducted by the Nationalist Government that aimed for the construction of a modern country was not only a field of politics, but on the other hand, the weak basis of the government operation became the obstacle to the realization of the political power of the revolutionary regime. Though the subject of records and archives administrative reform was postponed to the future, it should be understood that the consciousness of modern records and archives administration and overall studies began through this examination of administrative reform.