• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.786-789
• /
• 2002

A recurrent artificial neural network (ANN) model is developed to simulate hydrocarbon recovery process at petroleum-contaminated site. The groundwater extraction rate, vacuum pressure, and saturation hydraulic conductivity are selected as the input variables, while the cumulative hydrocarbon recovery volume is considered as the output variable. The experimental data fer establishing the ANN model are from implementation of a multiphase flow model for dual phase remediation process under different input variable conditions. The complex nonlinear and dynamic relationship between input and output data sets are then identified through the developed ANN model. Reasonable agreements between modeling results and experimental data are observed, which reveals high effectiveness and efficiency of the neural network approach in modeling complex hydrocarbon recovery behavior.

• Proceedings of the IEEK Conference
• /
• 1999.06a
• /
• pp.333-336
• /
• 1999

In this paper, a new high speed parallel input and parallel output GF(2$^{m}$ ) multiplier based on standard basis is proposed. The concept of the multiplication in standard basis coordinates gives an easier VLSI implementation than that of the dual basis. This proposed algorithm and method of implementation of the GF(2$^{m}$ ) multiplication are represented by two kinds of basic cells (which are the generalized and fixed basic cell), and the minimum critical path with pipelined operation. In the case of the generalized basic cell, the proposed multiplier is composed of $m^2$ basic cells where each cell has 2 two input AND gates, 2 two input XOR gates, and 2 one bit latches Specifically, we show that the proposed multiplier has smaller complexity than those proposed in 〔5〕.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.37 no.2
• /
• pp.130-137
• /
• 1988

The technique of dual-input describing function's synthesis is introduced and the construction of a nonlinear compensator, based on this technique, is proposed. A nonlinear compensator, describing a complex DIDF depending upon amplitude of the second sinusoidal input signal only, is also proposed, where the second sinusoidal input signal is supplied to the nonlinear compensator by external generator. This compensator, connected in a closed loop of the PI speed control of DC motor, can improve the speed response in view instability limit cycle, low speed response and disturbance of the dynamic shift of the Nyquist's critical point -1 + j O. It is verified theoretically that the improvement of speed response of DC motor using the proposed compensator is achieved by means of the dynamic shift of the Nyquist's critical point on the complex plane, and the speed characterstics of DC motor is to be tested through experiment for its performance.

• Journal of Power Electronics
• /
• v.16 no.4
• /
• pp.1288-1297
• /
• 2016

This study proposes a single-stage light-emitting diode (LED) tube lamp driver with input-current shaping for T8/T10-type fluorescent lamp replacements. The proposed AC-DC LED driver integrates a dual-boost converter with coupled inductors and a half-bridge series-resonant converter with a bridge rectifier into a single-stage power conversion topology. This paper presents the operational principles and design considerations for one T8-type 18 W-rated LED tube lamp with line input voltages ranging from 100 V rms to 120 V rms. Experimental results for the prototype driver show that the highest power factor (PF = 0.988), lowest input current total harmonic distortion (THD = 7.22%), and highest circuit efficiency (η = 92.42%) are obtained at an input voltage of 120 V. Hence, the proposed driver is feasible for use in energy-efficient indoor lighting applications.

• Journal of the Korean Society of Industry Convergence
• /
• v.20 no.2
• /
• pp.115-124
• /
• 2017

This paper aims to develop an SMPS topology for handling a high range of input voltages based on a DC-DC flyback converter circuit. For this purpose, 2 capacitors of the same specifications were serially connected on the input terminal side, with a flyback converter of the same circuit configuration serially connected to each of them, so as to achieve high input voltage and an effect of dividing input voltage. The serially connected flyback converters have the transformer turn ratio of 1:1, so that each coil is used for the winding of a single transformer, which is a characteristic of doubly-fed configuration and enables the correction of input capacitor voltage imbalance. In addition, a pulse transformer was designed and fabricated in a way that can achieve the isolation and noise robustness of the PWM output signal of the PWM controller that applies gate voltage to individual flyback converter switches. PSIM simulation was carried out to verify such a structure and confirm its feasibility, and a 100W class stack was fabricated and used to verify the feasibility of the proposed high voltage SMPS topology.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.43 no.4 s.346
• /
• pp.75-80
• /
• 2006

This paper has proposed a novel dual band transmitter module which can be operating either as an amplifier or as a frequency multiplier according to the input frequency. A conventional dual band transmitter consists of separate amplifiers operating at each frequency band, but the proposed dual band module operates as an amplifier for the IEEE 802.11b/g signal, and as a frequency doubler for the IEEE 802.11a signal according to input frequency and bias voltage. In this paper, we have obtained sharp stop band characteristics by using microstrip DGS(Defected Ground Structure) to suppress the fundamental frequency of the frequency doubler as well as the second harmonic of the amplifier. From measurement result, second harmonic suppression is below -59dBc in the amplifier mode, and fundamental suppression is below -35dBc in the frequency doubler mode. And the designed module has 17.8dBm output P1dB at 2.4GHz and 10.1dBm power for 5.8GHz output, and the output power in the two modes are 0.8dB and 2.8dB larger than the module with ${\lambda}g/4$ reflector, respectively.

• Journal of IKEEE
• /
• v.2 no.1 s.2
• /
• pp.15-23
• /
• 1998

In this paper, distributed mixer is studied at microwave frequency. The circuit of distributed mixer composed of gate 1,2, drain transmission lines, matching circuits in input and output terminal, DGFET's. For impedance matching of input and output port at higher frequency, image impedance concept is introduced. In distributed mixer, a DGFET's impedances are absorbed by artificial transmission line, this type of mixer can get a very broadband characteristics compared to that of current systems. A RF/LO signal is applied to each gate input port, and are excited the drain transmission line through transcondutance of the DGFET's. The output signals from each drain port of DGFET's added in same phases. We designed and frabricated the distributed mixer, and a conversion gain, noise figure, bandwidth, LO/RF isolation of the mixer are shown through computer simulation and experimentation.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.10a
• /
• pp.484-487
• /
• 2015

This paper describes a dual-input battery charger with MPPT control using photovoltaic and piezoelectric energy. Each energy is harvested from photovoltaic cells and piezoelectric cells and is stored to each capacitor. The battery voltage is boosted by charger block and two energy sources are used as input to charge battery capacitor. A DC-DC boost converter is designed to boost the battery voltage, and inductor sharing technique is employed such that only one inductor is required. The time division ratio for piezoelectric cell and photovoltaic cell is set to 8:1. The proposed circuit is designed in a 0.35um CMOS process technology. The condition of battery capacitor is managed by battery management block and the battery voltage can be boosted up to 3V. The maximum efficiency of the designed entire system is 88.56%, and the chip area including pads is $1230um{\times}1330um$.

• Environmental and Resource Economics Review
• /
• v.27 no.1
• /
• pp.29-66
• /
• 2018

This study constructs an energy-extended KLEM DB of 35 Korean industries, and estimates the elasticities of substitution under various nesting structures of production technologies. Unlike most existing studies that employed only three inputs, K, L, and E, we applied a dual approach where non-energy intermediate input M is also incorporated as a production input. Our dual approach which extended that of van der Werf (2008)'s 3-input model successfully identified and estimated the multi-nested production functions. We provide the estimates of the elasticities of substitution among 4 different energy sources as well. Our estimation results would be used for energy-environment model building for Korea.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.6
• /
• pp.1049-1056
• /
• 2016

In this paper, a design method for a compact dual-band slot antenna with bent slot is studied. Bent slots are added on the rectangular slot of the proposed antenna for dual-band operation. The rectangular slot is fed by a coaxial cable by placing a rectangular feeding patch inside the slot. When the bent slots are added onto the both corner of the upper side of the rectangular slot symmetrically, a new resonant frequency is created in low frequency because of the increasement of the slot length. A prototype of the proposed dual-band slot antenna operating at 2.45 GHz WLAN band and 4.50-8.30 GHz band including 5GHz WLAN band is fabricated on an FR4 substrate with a dimension of 30 mm by 30 mm. Experiment results show that the antenna has a desired impedance characteristic with a frequency band of 2.40-2.49 GHz and 4.33-9.85 GHz for an input reflection coefficient < -10 dB.