• Journal of Biosystems Engineering
• /
• 제34권5호
• /
• pp.351-357
• /
• 2009

This study was conducted to verify the simulation model through the drying test, and investigate effect of factors, such as temperature of drying air, airflow rate, and velocity of the airflow, on the drying. The low temperature drying simulation model was developed based on the circulation dry simulation model presented by Keum et al. (1987), and by modifying low temperature thin layer drying model, equilibrium moisture content model, latent heat of vaporization model, and crack ratio prediction model. The heat pump and experimental dryer with a capacity of 150kg were used for the test. The RMSE between the predicted and measured value was 0.27% (drying temperature), 0.15% (crack ratio), and 2.08% (relative humidity), so the relevance of the model was verified. In addition, the effect of drying temperature, airflow rate, and velocity of the airflow on the drying was examined. The experimental results showed that the crack ratio at drying temperature of $25{\sim}40^{\circ}C$ was allowable. Moreover, at below $30^{\circ}C$, variation of the crack ratio was slight, but drying time was delayed. Given these results, the drying temperature of over $30^{\circ}C$ was effective. As the airflow rate increased, required energy dramatically increased. Whereas drying rate slowly increased, so loss of drying efficiency was caused. Considering these results, the dryer needed to be designed and adjusted to lower than $30\;m^3/min{\cdot}ton$. As velocity of the airflow increased, required drying energy increased when the velocity of the airflow was over $5\;m^3$/hr, while crack ratio and drying rate showed little variation.

• 한국환경과학회지
• /
• 제30권3호
• /
• pp.245-255
• /
• 2021

In this study, we evaluated the effect of the type of sewage sludge (digested, non digested) on drying efficiency according to the polymer injection rate. The drying characteristics were shown using a near-infrared ray (NIR) and a microwave. As a result of the drying characteristics with NIR at a polymer dose ratio of 8%, the heating up period is up to 6 minutes after the start of the drying experiment. Afterwards, the constant rate drying period of the digested sludge (A, C and G sites) was 6 minute → 18 minute, showing a rapid decrease in moisture. On the other hand, non digested sludge (B, D, E, F, H, I, J and K sites) showed gradual drying characteristics compared to digested sludge until complete drying (10%). As the polymer dose ratio of 10% and 12%, the heating up period for digested sludge is up to 6 minute after the start of the experiment. Afterwards, the constant rate drying period of the digested sludge was 6 minute → 20 minute, showing a rapid decrease in moisture. On the other hand, the heating up period of non digested sludge was up to 10 minute after the start of the experiment, and the constant rate drying period was 10 minute → 22 minute, which was shorter than digested sludge. As a result of the drying characteristics with microwave at a polymer dose ratio of 8%, 10% and 12%, the constant rate drying period the digested sludge was 4 minute → 20~22 minute, showing a rapid decrease in moisture. On the other hand, non digested sludge of the constant rate drying period was 4 minute → 22~30 minute, which was longer than digested sludge.

• Journal of Biosystems Engineering
• /
• 제41권1호
• /
• pp.34-42
• /
• 2016

Purpose: This study was performed to improve the drying quality and drying rate of ginseng slices by combining microwave and far-infrared drying techniques. Methods: Based on single-factor experiments and analyses, a quadratic regression orthogonal rotation combination design was adopted to study the effects of the moisture content at the conversion point between the microwave and far-infrared techniques, the ginseng slice thickness and the far-infrared drying temperature on the chip drying time, the surface color difference value, the nutritional composition and the surface shrinkage rate index. Results: Compared to the far-infrared drying alone, the combined microwave and far-infrared drying resulted in an increase in the saponin content of the ginseng slices and reductions in the drying time, surface color difference, and shrinkage rate. Conclusions: We established a mathematical model of the relationships between the surface shrinkage rate index and the experimental factors using the multi-objective nonlinear optimization method to determine the optimal parameter combination, which was confirmed to be the following: microwave and far-infrared moisture contents of 65%, a ginseng slice thickness of 1 mm, and a far-infrared drying temperature of $54^{\circ}C$.

• Journal of the Korean Wood Science and Technology
• /
• 제35권4호
• /
• pp.45-51
• /
• 2007

로진을 이용하여 제조된 천연도료의 건조거동을 확인하기 위해 건조가 진행하는 동안의 천연도료의 질량변화와 스펙클 이미지(speckle image)를 통한 광학적 변화를 측정하였고, 두 측정방법 사이의 상관관계를 조사하였다. HORUS를 통해 측정된 스펙클 이미지에서는 선형 스케일에서 질량변화는 건조시간과 깊은 상관관계가 있으며, Log 스케일에서는 질량변화에 따른 영향뿐만이 아니라 건조거동에 따라 나타났다. 그러므로 HORUS를 이용하여 도료의 건조시간과 건조거동을 조사하는 하나의 방법으로 추천될 만한 것으로 검토되었다.

• Journal of Biosystems Engineering
• /
• 제40권3호
• /
• pp.232-237
• /
• 2015

Purpose: In Korea, wheat is dried using circulating cross-flow grain dryers. However, there is no research on wheat drying which can be utilized for the dryers. Therefore, this study developed and evaluated a simulation of the circulating cross-flow dryer, and examined the effects of various factors on drying performance. Methods: The simulation program was developed using drying models and was evaluated against wheat-drying experiments with a dryer having a 30-ton capacity. The influence of drying temperature, air volume, and grain falling rate on drying performance were examined through the simulation. Results: The experimental results validated the simulation program by showing the same root mean square error (RMSE) for moisture content (0.286%) and drying rate (0.056%/h) in both the experimental data and the simulation values. The appropriate wheat-drying parameter values, considering drying conditions, were determined to be $50^{\circ}C$ for drying temperature, $500m^3/min$ for air volume, and a grain falling rate of $36.0m^3/h$. Conclusions: The developed simulation program for circulating cross-flow dryers analyzed the influences of performance factors such as drying temperature, air volume, and falling rate on drying performance.

• 설비공학논문집
• /
• 제21권1호
• /
• pp.1-8
• /
• 2009

The simulation of a heat pump dryer has been carried out to figure out the effect of air flow rate on the drying performance represented by MER, SMER, and so on. The simulation includes the analyses of one-stage heat pump cycle and simple drying process using the drying efficiency. The heat pump cycle with Refrigerant 134a has been considered. In the dryer, some of drying air from the drying chamber flows through the heat pump system, the rest of air bypasses the heat pump system. The two air flows joins before the drying chamber inlet. The performance parameters considered in the present study are MER, SMER, the temperature and humidity of drying air. Those parameters are compared for different total air flow rate or bypass air flow rate.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.242-247
• /
• 2009

The present study has been conducted to reduce the cold air drying rate. According to the cold air drying method, the quality-excellent product could be made and there would be little change of color, taste and smell. As compared with the hot air drying, the cold air drying equipment has the superior dehumidification in a constant drying zone. However, in a falling drying zone that equipment is not energy-efficient because the drying period could be longer by the dehumidificated.

• Journal of Ginseng Research
• /
• 제39권4호
• /
• pp.371-375
• /
• 2015

Background: The current typical drying methods for red ginseng are sun drying and hot-air drying. The purpose of this study was to investigate drying characteristics of red ginseng by using far-infrared drying. Methods: The far-infrared drying tests on red ginseng were conducted at two drying stages: (1) high temperature for 24 h drying and (2) low temperature drying until the final moisture content was $13{\pm}0.5%$ (wet basis). The high temperature drying stage included three drying chamber temperature conditions of $60^{\circ}C$, $65^{\circ}C$, and $70^{\circ}C$. The low temperature drying stage was conducted at temperatures of $45^{\circ}C$ and $50^{\circ}C$. Drying characteristics were analyzed based on factors such as drying rate, color changes, energy consumption, and saponin content. The results were compared with those of the hot-air and sun drying methods. Results: The results revealed that increases in drying temperature caused a decrease in drying time and energy consumption for far-infrared drying. The saponin content decreased under all drying conditions after drying, the highest value (11.34 mg/g) was observed at drying conditions of $60{\sim}50^{\circ}C$. The sun drying condition showed the lowest color difference value when compared with far-infrared and hot-air drying. Conclusion: The far-infrared drying showed a faster drying rate, higher saponin content, lower color difference value, and a decrease in energy consumption than seen in hot-air drying.

• Journal of the Korean Wood Science and Technology
• /
• 제33권6호통권134호
• /
• pp.25-30
• /
• 2005

두께 50 mm 국산 소나무(Pinus densiflora Sieb. et Zucc.) 판재의 건조스케줄 개량을 위해 일반 열기 건조스케줄, 시간 기준 건조스케줄, 연속 온도상승 건조스케줄, 그리고 습구온도 조절 건조스케줄을 적용하여 최종함수율 15% 정도까지 건조한 후 각각의 건조스케줄 적용에 의한 건조특성을 비교분석하였다. 두께 50 mm 국산 소나무의 일반 열기 건조스케줄 적용실험 결과 건조속도는 0.53%/hr, 시간 기준 건조스케줄 적용에 의한 건조속도는 0.9%/hr, 그리고 연속 온도상승 건조스케줄 적용에 의한 건조속도는 2.29%/hr였으며, 습구온도 조절 건조스케줄 적용에 의한 건조속도는 1.52%/hr였다.

• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.254-259
• /
• 2009

The mixed cooling dryer has been developed significantly by adopting both advantages of cooling dryers and desiccant dryers. In this study, it is introduced that the desired effect, such as drying rate period reduction and energy-saving, could be achieved only by adding the desiccant dryer if an existing cooling dryer is used. The experiment should be conducted for quite long time due to the material selection, so it is regrettable that there are not enough data.