• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.8 s.185
• /
• pp.47-53
• /
• 2006

The purpose of this study was to investigate the significant characteristics in spray of industrial etch-nozzle for the design of process. The experiment was carried out with different spray pressure and industrial nozzle in wet etch. The characteristics of liquid spray, such as axial velocity and sauter mean diameter measurements were obtained by PDA. And impact force was calculated from spray characteristics. It was found that the fluid with higher spray pressure resulted in the smaller SMD and the higher droplet velocity and impact force. The depth of etch was increased in case of high spray pressure. In the case of injection angle oscillated between $20^{\circ}$, the result indicated constant effect of etch. The correlation between the spray characteristics and etch ones were analyzed. The depth of etch had good positive correlation with axial velocity and impact force. The result clearly shows that the characteristics in wet etch are strongly related to the spray characteristics with process.

• Journal of ILASS-Korea
• /
• v.23 no.4
• /
• pp.205-211
• /
• 2018

Y-jet nozzle has various advantages over other twin-fluid nozzles and are used in industrial boilers. However, it costs large energy consumption because of assisted air and its design is complex. The Y-jet nozzle is consisted of a liquid and gas port and a mixing chamber. The diameter of the port and the length of the mixing chamber greatly affect spray and atomization characteristics, therefore, they are the most important factors in nozzle design. In this study, The experimental setup is consisted of a laboratory scale spray system. The characteristics of the Y-jet nozzle according to the design parameters were observed. As a result, it was found that the length of the mixing chamber did not have effect on the flow rate and the choking condition. The droplet size was measured using a Malvern type measuring device. In addition, measurements were conducted in the front and the right directions of the nozzles. Based on the results, the SMD View Ratio is defined. It is the asymmetrical design characteristics of the Y-jet nozzle.

• Korean Journal of Food Science and Technology
• /
• v.15 no.4
• /
• pp.342-347
• /
• 1983

The effects of barley tea concentration and atomizing air pressure on the size, homogeneity and distribution of the sprayed droplets were investigated. An equation relating mean diameter (${\overline{D}}$) with the concentration where the coefficient a and b were determined empirically. As the operating air pressure was increased, the mean diameter of the droplets decreased and finally reached the limiting mean diameter, $36{\mu}m$ at 15.7% barley tea concentration. The homogeneity of the droplets increased with the operating air pressure, increase and it was decreased steadily as the soluble solid concentration increased up to 20% and markedly over 20% at every operating air pressure. The distribution ($P_D$) of sprayed droplets related with the droplet size as the following exponential equation; $P_D$ = e 1nD + f where e and f are empirical constants.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.38 no.3
• /
• pp.201-207
• /
• 2012

The influence of different dilution procedures on the properties of oil-in-water (O/W) nano-emulsions obtained by dilution of oil-in-ethanol (O/E) microemulsions with water has been studied. The system water/ethanol/nonionic surfactant/silicone oil with ethanol was chosen as model system. The dilution procedures consisted of adding water (or microemulsion) stepwise. By mixing O/E microemulsions into water, nano-emulsions with droplet diameters of 30 nm were obtained. In contrast, by mixing water into O/E microemulsion, emulsions with diameter of 400 nm were obtained The dilution methods were shown to be a key factor determining the properties of the emulsions. There were no change in diameters of nanoemulsion droplets against time, however sizes of droplets in the emulsion with larger droplets were increased with time and the mechanism of unstability was thought to be Ostwald ripening.

• Journal of Digital Convergence
• /
• v.10 no.5
• /
• pp.283-288
• /
• 2012

This study was undertaken to investigation the spray characteristics of the twin fluid atomization nozzle system. The light oil was injected at the normal temperature and injection pressure was 5 bar - 10 bar by 1 bar and volume flow was 0.5, 1.0 and 2,0 mmH2O(X10-2). We measured the SMD of sprayed droplet to study spray characteristics. The following conclusions were reached from the results of these study. 1. The more injection pressure increased, the more SMD decreased. 2. The more measuring distance between pressure nozzle tip and analyser beam increased, the more SMD increased. 3. SMD of the blower-air-added injection system were shown, increasing volume flow decreased respectively. The result of this study indicated the blower-air-added injection system induced beneficial changes in SMD. And it will be considered important indicator for spray characteristics design and performance evaluation of twin fluid atomization nozzle system.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.44 no.12
• /
• pp.1017-1026
• /
• 2016

The present paper describes the two off-surface visualization techniques and their application examples to vortex flows. One of the two visualization techniques is the classical smoke-wire technique, and the other is the visualization technique using the micro water-droplets generated by the home-style ultrasonic humidifier. The smoke-wire technique has the limit of air flow speed (about 5 m/sec for 0.07 mm-diameter wire) and the pollution problem, but it produces very fine and clear streak line sheet. It is applied to visualize the wing-tip vortices of a 3-dimensional wing. The micro water-droplet technique has the larger limit of air flow speed (above 10 m/sec) and is free from pollution and toxic problems compared to the smoke-wire technique. It is successfully applied to visualize the complex vortex system of a double-delta wing with an apex strake.

• Journal of Digital Convergence
• /
• v.13 no.4
• /
• pp.417-423
• /
• 2015

Oil-in-water(o/w) nanoemulsions were prepared in the system of water/Span 80-Tween 80/long-chain paraffin oil via PIC method. With the increase of preparation temperature from 30 oC to 80 oC, the diameter of emulsion droplets decreased from 150 nm to 40 nm. By varying the HLB of mixed surfactants, we found that there was an optimum HLB around 13.0~14.0 corresponding to the minimum droplet size. The size of emulsion droplets increased upon increasing the ratio of oil/emulsifying agent. At $f{\leq}0.15$, the size of nanoemulsions could be kept constant more than 2 months. The increase in preparation temperature makes it possible for producing monodisperse nanoemulsions. Once the nanoemulsion is produced, the stability against Ostwald ripening is outstanding due to the extremely low solubility of the liquid paraffin oil in the continuous phase.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.732-737
• /
• 2005

Distal 3D Real Object Duplication System(RODS) consists of 3D Scanner and Solid Freeform Fabrication System(SFFS). It is a device to make three-dimensional objects directly from the drawing or the scanning data. In this research, we developed an office type SFFS based on Three Dimensional Printing Process and a industrial SFFS using Dual Laser. An office type SFFS applied sliding mode control with sliding perturbation observer(SMCSPO) algorithm for control of this system. And we measured process variables about droplet diameter measurement and powder bed formation etc. through experiments. Also, in order to develop more elaborate and speedy system for large objects than existing SLS process, this study applies a new Selective Multi-Laser Sintering(SMLS) process and 3-axis dynamic Focusing Scanner for scanning large area instead of the existing $f\theta$ lens. In this process, the temperature has a great influence on sintering of the polymer. Also the laser parameters are considered like that laser beam power, scan speed, scan spacing. Now, this study is in progress to eveluate the effect of experimental parameters on the sintering process.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.11
• /
• pp.848-853
• /
• 2010

We have grown GaN nanowires by the low pressure MOCVD method on Ni deposited oxidized Si surface and have established optimum conditions by observing surface microstructure and its photoluminescence. Optimum growth temperature of $880^{\circ}C$, growth time of 30 min, TMG source flow rate of 10 sccm have resulted in dense nanowires on the surface, however further increase of growth time or TMG flow rate has not increased the length of nanowire but has formed nanocrystals. On the contrary, the increase of ammonia flow has increased the length of nanowires and the coverage of nanowire over the surface. The shape of nanowire is needle-like with a Ni droplet at its tip; the length is tens of micron with more than 40 nm in diameter. Low temperature photoluminescence obtained from the sample at optimum growth condition has revealed several peaks related to exciton decay near band-edge, but does not show any characteristic originated from one dimensional quantum confinement. Strong and broad luminescence at 2.2 eV is observed from dense nanowire samples and this suggests that the broad band is related to e-h recombination at the surface state in a nanowire. The current result is implemented to the nanowire device fabrication by nanowire bridging between micro-patterned neighboring Ni catalysis islands.

• Journal of Embryo Transfer
• /
• v.15 no.3
• /
• pp.271-277
• /
• 2000

This study was conducted to establish the optimal culture conditions for in vitro production of bovine embryos derived from slaughter house ovaries. Cumulus-oocyte- complexes (COCs) collected by aspiration from follicles of 2~7 mm in diameter were matured in Ham's F-10 medium supplemented with 0.01 $\mu\textrm{g}$/m1 epidermal growth factor (EGF) at 39$^{\circ}C$ in a humidified atmosphere of 5% $CO_2$in air. After 24 hrs of culture, the oocytes were co-cultured with epididymal sperm selected off by Percoll-density gradient in TALP medium for 24 hrs. The presumptive zygotes were cultured in HECM-6 medium for 3 d post-insemination, and followed by cultured in TCM199 medium until 7 to 10d post-insemination. The cultures were compared of their cleavage and development into later stage in culture medium by additions of different protein sources (PVA, BSA and BCS) and by different embryo density. The rates of cleavage and development rates into blastocyst were not significantly (P<0.05) different among the culture media containing with BSA (75.0% and 40.5%), BCS (76.7% and 38.0%) and PVA (72.5% and 42.2%), respectively. Significantly (P<0.05) higher blastocysts rates were obtained in culturing of 30 and 40 embryos in each 50$\mu$l droplets of culture medium than in 5, 10 and 20 embryos. These results indicate that the optimal density of embryos is 30~40 embryos in a 50$\mu$l droplet of culture medium. Furthermore there is no effect of different protein sources on early embryonic development.