• 한국항공우주학회지
• /
• 제33권4호
• /
• pp.71-78
• /
• 2005

초임계 상태의 질소 유동 환경에서 헵탄 액적의 기화 특성을 수치적으로 연구하였다. 더불어 실기체 효과와 액적 내부 순환, 다양한 열역학적 물성치 및 고압 효과를 고려하였다. 또한 헵탄 액적 바로 근처에서의 저속 유동 문제를 풀기 위하여 예조건화 스킴을 적용한 시간 전진법을 수치 코드에 적용하였다. 주위 유동 속도와 주위 압력을 변화 시켜가면서 액적의 거동을 살펴보았다. 유동 속도 증가로 인한 레이놀즈수의 증가에 따라 액적의 변형이 활발히 이루어졌고, 동일한 레이놀즈수에 대해서는 압력이 높아질수록 액적의 변형이 약화되었다.

• 대한기계학회논문집B
• /
• 제30권2호
• /
• pp.161-169
• /
• 2006

The spray characteristics of liquid jet in cross flow with variation of injection angle are numerically studied. Numerical analysis was carried out using KIVA code, which was modified to be suitable for simulating liquid jet ejected into cross flow. Wave model and Kelvin-Helmholtz(KH)/Rayleigh-Taylor(RT) hybrid model were used for the purpose of analyzing liquid column, ligament, and the breakup of droplet. Numerical results were compared with experimental data in order to verify the reliability of the physical model. Liquid jet penetration length, volume flux, droplet velocity profile and SMD were obtained. Penetration length increases as flow velocity decreases and injection velocity increases. From the bottom wall, the SMD increases as vertical distance increases. Also the SMD decreases as injection angle increases.

• 한국분무공학회지
• /
• 제11권2호
• /
• pp.81-88
• /
• 2006

The spray characteristics of the rotating fuel injection system were investigated. The special test rig was devised to get the spatial and momentary droplet information. This experimental apparatus consists of a high-speed motor, a shaft, a rotating fuel nozzle and an acrylic case. Spray droplet size and velocity were measured by PDPA(Phase Doppler Particle Analyzer) and instantaneous velocity field was measured by 1'IV (Particle Image Velocimetry) system. At the same time, spray visualization was performed by using ND-YAG laser-based flash photography. From these two different laser diagnostic techniques, we could get spatial and instantaneous spray information fur rotating fuel injection system. The results presented in this paper indicate that spray characteristics such as droplet size, velocity and spray pattern were strongly influenced by rotational speed.

• 한국분무공학회지
• /
• 제3권1호
• /
• pp.34-42
• /
• 1998

The correlation between the droplets size and the velocity are investigated for an intermittent spray of the pintle type fuel injector employed in a port injection gasoline engine. The analysis such as the mean droplet size, SMD, and velocity under the fixed injection period and varied fuel pressures are conducted utilizing PDPA systems. As results, the experimental data obtained, show that the larger droplet sizes. the higher velocities during the spray tip arrival time, and that at Z=70mm, r=8mm, both droplet sizes and velocities are peak. At the upstream, flow of droplets are dominated by injection pressure, which are more effected inertia force of droplets at the downstream of Z=70mm.

• Journal of Welding and Joining
• /
• 제7권3호
• /
• pp.55-62
• /
• 1989

Variation of the spray droplet velocity with spraying distance and the microstructural characteristics of spray deposits fromed by oxy-fuel thermal spraying with Ni-base alloy powder contained chrome boride for hard facing were examined. Measurements of spray droplet velocity as a function of distance from the nozzle tip were inexcellent agreement with computer simulated predictions. Optimum condition for thermal spray deposits in this experiment was found to be under #10kg/cm^2$ of acceleration gas pressure with 15cm of spraying distance. Fine microstructure and higher microhardness of the initial part of the deposits due to rapid solidification were found to be able to maintained in a thickness up to 0.4mm, and this initial microstructure and properties could be maintained throughout the thickness of a thick spray deposits by performing the multipass spraying with 0.4mm thickness of each pass.

• 수산해양기술연구
• /
• 제28권4호
• /
• pp.418-429
• /
• 1992

Recently, many researchers make a great effort to develop high efficient marine diesel engines using low grade heavy oil, and also study substitution fuel oil for engines and boilers. In case of Fisheries Vessels, we need to know that fish oil can be substituted for fuel oil. Therefore, it is studied that evaporation, ignition and combustion phenomena of the single droplet of fish oils (i.e., Sardine fish oil, File fish oil and Alaska pollac oil) on heated plane surface to evaluate appropriateness as substitution oil. Methanol and light oil are tested simultaneously to help the evaluation on these Fish oils. The results are summarized as follows: 1. The type of evaporation and combustion is spherical evaporation in case of methanol and light oil. And fish oil blended with light oil was finished after spherical evaporation happen when high temperature. 2. Ignition of Pure fish oil was shorter than that of fish oil blended with light oil. 3. Heat transferred to droplet could make qualitative comparison by contact diameter of droplet with hot surface as time changes. Life time of droplet according to the change of heated surface temperature was greatly influenced by droplet contact condition on the heated surface. 4. As far as combustion phenomena was concerned, apparent diameter of the fish oil droplet increased after ignition and decreased suddenly by internal boiling of droplet. 5. Three fish oils had similar phenomena on the evaporation, ignition and combustion. 6. Evaporation and combustion feature of fish oil could not be shown by coefficient of evaporation velocity of droplet and coefficient of combustion velocity of droplet.

• 한국분무공학회지
• /
• 제1권1호
• /
• pp.28-34
• /
• 1996

Study on the mechanism of droplet transport and the droplet eddy diffusivity in the intake manifold of internal conbustion engine with carburetor has been carried out in this paper The theory and experiments were studied and performed respectively, to elucidate the mechanism and to measure typical rates of deposition, on the walls of a straight type intake manifold, of water droplets suspended in a turbulent air streams. Accordingly, the results are that Mechanism of a spray transport to the walls is caused by the fluctuation component of radial velocity. Deposition rate of a spray on the walls is mainly dependent upon air velocity and mean diameter of spray, and Droplet eddy diffusivity in the intake manifold is around $80\sim105cm^2/sec$.

• 한국전산유체공학회지
• /
• 제8권4호
• /
• pp.6-15
• /
• 2003

It is an aim of this study to perform extensive numerical study for analyzing the anisotropic turbulence effects on spatial and temporal behaviors of droplet for impinging sprays. The turbulence model of Durbin is used for comparisons with the k-ε model. The turbulence-induced dispersions of droplets are considered to describe the anisotropy of turbulence effectively and spray/wall interactions are simulated using the model of Lee and Ryou. Present study investigates the overall and the internal structures of impinging diesel sprays such as spray shapes, radius and height of wall sprays, Sauter mean diameter (SMD), local droplet velocity, and local gas velocity and compared the results with experimental data by two adopted turbulence models. When the anisotropy effect of turbulence is included, better predictions for both gas and droplet tangential velocities are obtained, compared to the k-ε model. It is concluded that anisotropic effect of turbulence should be considered for simulating impinging diesel sprays.

• 한국분무공학회지
• /
• 제6권4호
• /
• pp.31-38
• /
• 2001

The Holographic Particle Velocimetry system can be a promising optical tool for the measurements of three dimensional particle velocities. In this study, the holographic panicle velocimetry system was used to measure the sizes and velocities of droplets formed by a commercial full cone spray nozzle. Uncertainty analysis was performed to identify the sources of all relevant errors and to evaluate their magnitude. The droplet velocities ranged from 10.3 to 13.3 m/s with average uncertainty of ${\pm}1.6m/s$, which is ${\pm}14%$ of the mean droplet velocity. Compared with relatively small uncertainties of velocity components in the normal direction to the optical axis, the uncertainty of the optical axis component is ${\pm}3.6m/s$. This is due to the long depth of field of droplet images in the optical axis, which is inherent feature of holographic system using forward-scattering object wave of particles.

• 한국분무공학회지
• /
• 제3권3호
• /
• pp.42-48
• /
• 1998

This study describes the spray structure of gasoline port injectors by using phase Doppler particle analyzer(PDPA) and particle motion analysis system(PMAS). The characteristics of fuel spray such as the spray penetration, spray angle and breakup processes were obtained by PMAS and the droplet size and mean velocity were measured by PDPA system. Pintle type and two-hole type injectors were used as gasoline port fuel injectors under various injection pressures. The effect of injection pressure on the droplet mean diameter and axial mean velocity of droplet were investigated under the various injection conditions. In addition the comparison of breakup processes for the two types of injectors was also conducted. It Is shown that pintle type injector has smaller droplet size than that of two-hole type injector.