• 대한기계학회논문집
• /
• 제18권3호
• /
• pp.662-669
• /
• 1994

In the combustion system, the optimum spray conditions reduce the pollutant emission of exhaust gas and enhance the fuel efficiency. The spray characteristics-the drop size, the drop velocity, the number density and the mass flux, become increasingly important in the design of combustor and in testifying numerical simulation of spray flow in the combustor. The purposes of this study are to clarify the spray characteristics of twin-fluid nozzle and to offer the data for combustor design and the numerical simulation of a spray flow. Spatial drop diameter was measured by immersion sampling method. The mean diameter, size distribution and uniformity of drop were analyzed with variations of air/liquid mass flow ratio. The results show that the SMD increases with the liquid supply flow rate and decreases with the air supply velocity. The radial distribution of SMD shows the larger drops can diffuse farther to the boundary of spray. And the drop size range is found to be wider close to the spray boundary where the maximum SMD locates.

• 마이크로전자및패키징학회지
• /
• 제18권2호
• /
• pp.35-41
• /
• 2011

Recently, board level solder joint reliability performance of IC packages during drop impact becomes a great concern to semiconductor and electronic product manufacturers. The handheld electronic products are prone to being dropped during their useful service life because of their size and weight. The IC packages are susceptible to solder joint failures, induced by a combination of printed circuit board (PCB) bending and mechanical shock during impact. The board level drop testing is an effective method to characterize the solder joint reliability performance of miniature handheld products. In this paper, applying the JEDEC (JESD22-B111) standard present a finite element modeling of the FBGA. The simulation results revealed that maximum stress was located at the outermost solder ball in the PCB or IC package side, which consisted well with the location of crack initiation observed in the failure analysis after drop reliability tests.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2001년도 하계종합학술대회 논문집(1)
• /
• pp.237-240
• /
• 2001

Dense Wavelength division multiplexing(DWDM) lightwave system requires multiplexer, demultiplexer and optical filter. In this paper, thus, we propose the Add-Drop Mux/Demux based on a Mach-Zehnder interferometer(MZI) with fiber Bragg grating(FBG). The Add-Drop Mux/Demux using FBG and MZI is able to minimize system and reduce weight. We also analyze output characteristics of Add-Drop Mux/Demux and present the optimum design data through the computer simulation.

• Geomechanics and Engineering
• /
• 제30권6호
• /
• pp.539-549
• /
• 2022

Accidental anchor drop can cause disturbances to seabed materials and pose significant threats to the safety and serviceability of submarine structures such as pipelines. In this study, a series of anchor drop tests was carried out to investigate the penetration mechanism of a Hall anchor in sand and clay. A special anchor drop apparatus was designed to model the inflight drop of a Hall anchor. Results indicate that Coriolis acceleration was the primary cause of large horizontal offsets in sand, and earth gravity had negligible impact on the lateral movement of dropped anchors. The indued final horizontal offset was shown to increase with the elevated drop height of an anchor, and the existence of water can slow down the landing velocity of an anchor. It is also observed that water conditions had a significant effect on the influence zone caused by anchors. The vertical influence depth was over 5 m, and the influence radius was more than 3 m if the anchor had a drop height of 25 m in dry sand. In comparison, the vertical influence depth and radius reduced to less than 3 m and 2 m, respectively, when the anchor was released from 10 m height and fell into the seabed with a water depth of 15 m. It is also found that the dynamically penetrating anchors could significantly influence the earth pressure in clay. There is a non-linear increase in the measured penetration depth with kinematic energy, and the resulted maximum earth pressure increased dramatically with an increase in kinematic energy. Results from centrifuge model tests in this study provide useful insights into the penetration mechanism of a dropped anchor, which provides valuable data for design and planning of future submarine structures.

• 한국통신학회논문지
• /
• 제29권2B호
• /
• pp.203-209
• /
• 2004

OBS 네크워크에서 contention으로 인한 burst의 drop은 TCP의 성능에 중요한 영향을 끼치는 요소이나, 기존의 drop policy에서는 이를 고려하지 않으며 TCP에 대한 연구로는 burst의 assembling이 주를 이루고 있다. 본 논문에서는 OBS 네트워크에서 TCP의 재전송 문제를 drop policy와 연계하여 TCP의 성능을 향상시키고자 한다. 본 논문에서 제안하는 drop policy는 burst의 재전송 횟수가 drop을 결정하는데 있어서 priority로 작용하는 Retransmission Count-based DP(RC-based DP)이다. RC-based DP 모델과 general DP 모델의 성능을 ns-2를 이용한 시뮬레이션을 통해 평가하며, 이 때 시간의 변화에 따른 TCP throughput, 목적지에서 수신한 최고 Sequence 번호, 패킷의 drop rate을 비교 분석한다.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1984-1990
• /
• 2011

This paper presents the simulation of traction power supply system for the evaluation of voltage drop in Kyungbu high speed line. This simulation is performed in circumstance of extended feeding through vicinity substation. Extended feeding should be considered from design of system. Therefore, voltage drop at extended feeding must be accepted against regulation. In this paper, voltage drop is evaluated under condition of extended feeding targeting section from Shinchungju and Pyungtaek S/S.

• 한국정밀공학회지
• /
• 제24권10호
• /
• pp.99-108
• /
• 2007

As the structure of a mobile phone becomes thin to catch up with a slim product trend, the reliability of a LCD module is on the rise as a big issue for a product design. A drop test is the most basic and important verification method for a mechanical quality control but it requires much time and cost during a product development process. Thus many manufacturers have considered design guide lines using CAE and simulation for more effective usage of limited resources on the market. In this paper, the Maximum Principle Stress of a LCD glass panel is calculated on the basis of explicit FE Analyses method and input conditions are determined according to the general test standard. The design guideline for reliability improvements are suggested on the basis of the results of FE Analysis.

• Advances in Computational Design
• /
• 제5권3호
• /
• pp.261-276
• /
• 2020

The reasonable layout of vacuum cleaner can effectively improve the collection efficiency of iron filings generated in the process of steel production. Therefore, in this study, the CFD-DEM coupling model and two-fluid model are used to calculate the iron filings collection efficiency of vacuum cleaner with different inclination/cross-sectional area, pressure drop and inlet angle. The results are as follows: The CFD-DEM coupling method can truly reflect the motion mode of iron filings in pneumatic conveying. Considering the instability and the decline of the growth rate of iron filings collection efficiency caused by high pressure drop, the layout of 75° inclination is suggested, and the optimal pressure drop is 100Pa. The optimal simulation results based on two-fluid model show that when the inlet angle and pressure drop are in the range of 45°~65° and 70Pa~100Pa, larger mass flow rate of iron filings can be obtained. It is hoped that the simulation results can offer some suggestion to the layout of vacuum cleaner in the rolling mill.

• 한국항공우주학회지
• /
• 제37권2호
• /
• pp.193-200
• /
• 2009

본 논문에서는 소형항공기용 유-공압 방식(oleo pneumatic type) 착륙장치의 낙하특성을 연구하였다. 본 연구대상의 착륙장치의 방식은 미터링 핀이 없는 단순 유-공압 방식댐퍼 이다. 일반적으로 유-공압 방식의 착륙장치는 단순한 구조로 되어 있어 무게가 가볍고 좋은 충격흡수 효율을 가진다. 낙하해석을 위하여 상용 코드인 MSC ADAMS를 이용하여 모델링 하였다. 모델링한 후에 해석과 시험결과의 상사성을 검증하기 위하여 일련의 시험이 수행되었다. 시험과 해석결과의 보다 좋은 일치성을 얻기 위하여 해석 모델에 공동현상 효과가 고려되었다. 공동현상을 고려한 착륙장치의 동적 거동 시뮬레이션 결과들이 현저하게 개선되었으며 시험결과와 보다 잘 일치함을 확인하였다. 이러한 과정을 통해 신뢰성이 검증된 해석모델을 이용하여 경사면에 대해서 해석적 방법을 통해 낙하특성을 예측하였다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 춘계학술대회 논문집
• /
• pp.710-713
• /
• 2005

Many impact or drop test researches of home appliances are published, but those of toys cannot be found easily. External impacts are the primary causes of fracture of toys. For impact proof design, the finished product should pass an impact test after molding design. There are several international toy safety standards or requirements such as US CPSC(Consumer Product Safety Commission), ASTM F963-96a, EN71 and so on. The puppy robot which patrols around the house, namely, the watchdog was selected to investigate toy safety because it has considerable weight and outer panels are made of plastics. First the model of watchdog robot was obtained by 3 dimensional scan. Surface data can be generated from 3D polygon data of the watchdog. A reliable drop simulation method for the watchdog was established using Pam-crash program according to Korean toy safety standards. When there is a low impact allowance value, the molding design should be reinforced or changed. It was found that the maximum impact stress reaches the ultimate stress of panel material.