• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.4
• /
• pp.456-462
• /
• 2015

The objective of this study was to develop an advanced pump technology using tornado and axial pumping principles without priming water. The developed rotor type slurry pump consisted of an electric motor, driving shaft and coupling, a rotor, an impeller, suction and discharge pipes. For the clean water test, the experimental results are presented for the discharge flowrate, electric power input and vacuum pressure with the rotor design parameters as a function of the motor rpm. The slurry discharge characteristics with the solid concentration of the cement slurry was performed. As the rotor diameter and height increase, the discharge flowrate and electric power input increase while the vacuum pressure in the suction pipe decreases. The rotor thickness had no significant effect on the discharge flowrate and electric power input. Slurries with more than 18 % solid concentration, which is the development factor, can be pumped.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.34 no.11
• /
• pp.1749-1755
• /
• 2010

The performance of power window system was decided by driving characteristics of the window regulator part and reaction by the glass run. The performance of power window system usually has been predicted by experimental methods. In this paper, an analytical method using the explicit code was suggested to overcome the limit of the experimental methods. The friction coefficient of glass run was obtained by the friction test at various conditions and the Mooney-Rivlin model was used. Also, a mechanism of window regulator consisted of the fast belt system and the slip ring elements. And, we conducted the analysis considering characteristic of a motor and obtained the lifting speed of automotive glass with high reliability

• Journal of the Korean Society for Railway
• /
• v.14 no.6
• /
• pp.507-514
• /
• 2011

Recently, we developed a new subway train with many cooperative companies. The main controller of the subway train is Control and Monitoring System (TCMS), so we conducted requirement analysis of TCMS considering system performance, easy maintenance and service oriented flexibility. Hence, we adopted new bus architecture and QNX as a Real-time Operating System (RTOS) and developed hardware systems. The functions of TCMS are employed into two computers, service computer and control/monitor computer, to increase on their performance and to yield easy maintenance and to satisfy customer needs. The TCMS controls and monitors control devices equipped in the train through various protocols which are implemented in hardware. In order to evaluate the performance of the system and to satisfy reliability, various experiments including EMC/ECI were performed. Now the TCMS is installed on the newly developed train and is under performance evaluation through test driving.

• Elastomers and Composites
• /
• v.44 no.1
• /
• pp.63-68
• /
• 2009

Recently, much attention has focused on the permanent deformation of roads in hot summer and cracks in cold winter, which are detrimental to safe driving. This leads to necessity of modification of asphalt to resist those deformation. In this study, a type of modified asphalt was prepared by addition of a photoinitiator which is activated by ultraviolet lay. The mechanical and rheololgical properties of photoinitiator-modified asphalt were examined using UTM and rheometer. Results showed that the modified asphalt was effected by ultraviolet and thus tensile strength and storage modulus increased, due to molecular attraction, with initiator content and irradiation dose. Thermal analysis showed less weight loss upon photoinitiator-modification and this indicated that the molecular attraction is the result of cross linking reaction between asphalt molecules induced by photoinitiator. According to long term ultraviolet curing test, properties of the photoinitiator-modified asphalt did not decrease or even increase for 20 years. This indicates that useful life of the asphalt could be extended by addition of photoinitiator.

• Elastomers and Composites
• /
• v.45 no.3
• /
• pp.217-222
• /
• 2010

Paved roads are suffered from the permanent plastic deformation in hot summer and cracks in cold winter, which are detrimental to safe driving. This leads to necessity of modification of asphalt to resist those deformation. In this study, two kinds of modifiers were examined; organic polymers and a photoinitiator which is activated by ultraviolet lay. The mechanical and rheololgical properties of modified asphalts were examined using UTM and rheometer. Results showed that the properties were varied depending on the types of polymer and irradiation time. UV irradiation increased the tensile strength and storage modulus of thermoplastic polymer-modified asphalt, however UV was not effective on thermoset polymer. According to long term ultraviolet curing test, properties of the polymer/photoinitiator-modified asphalt did not decrease, but rather increase for 20 years. This indicates that the useful life of the asphalt could be extended by addition of photoinitiator.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.45 no.3
• /
• pp.44-53
• /
• 2008

In this paper, we present the design of delta-sigma modulation-based class-D amplifier for driving headphones in portable audio applications. The presented class-D amplifier generates PWM(pulse width modulation) signals using a single-bit fourth-order high-performance delta-sigma modulator. To achieve a high SNR(signal-to-noise ratio) and ensure system stability, the locations of the modulator loop filter poles and zeros are optimized and thoroughly simulated. The test chip is fabricated using a standard $0.18{\mu}m$ CMOS process. The active area of the chip is $1.6mm^2$. It operates for the signal bandwidth from 20Hz to 20kHz. The measured THD+N(total harmonic distortion plus noise) at the $32{\Omega}$ load terminal is less than 0.03% from a 3V power supply.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.23 no.1
• /
• pp.65-73
• /
• 2015

The ride quality has become a key component of not only design but car selling as the technology developed and the requirement of passengers grew up. Thus car industry invests lots of time and cost for the higher ride quality. The evaluation of the ride quality mainly is expressed by subjective element that drivers felt. In this paper, instead of the original transfer path analysis method, relatively new methods such as OPAX(Operational path analysis with eXogeneous inputs) and OTPA(operational transfer path analysis) are used for analyzing the main hindrance element of ride quality. With those new method, contribution rate of all paths that the vibration propagate along analyzed after driving test on the roads having different characteristic. The comprehensive hindrance elements of ride quality are deduced from the contribution rate and the improve experiment by changing one of hindrance elements for higher ride quality.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.1
• /
• pp.277-283
• /
• 2020

In a concentric magnetic gear, which replaces the teeth of a mechanical gear with a permanent magnet, the polar ratio of the magnet that determines the reduction ratio affects the behavior of the magnetic gear dramatically. This study analyzed the density of transmission torque, the efficiency of torque considering the solid loss, and the torque quality, including the cogging characteristics using finite element analysis. When the pole number on the driving side was changed from two to five, it was confirmed that there was an optimal pole ratio, in which the transmission torque was maximized. Because eddy current generation density is proportional to the magnetic field, the transmission efficiency also shows a similar tendency to the transmission torque density, and the efficiency is more than 95% at a low gear ratio. The cogging characteristics due to the interaction of the permanent magnets with the limited number of poles are inversely proportional to the least common multiple between the number of magnets on the drive side and the number of modulator teeth. A test model was built for the transmission torque evaluation.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.21 no.8
• /
• pp.1553-1559
• /
• 2017

This paper proposes a lane departure detection algorithm using a single camera equipped in front of a vehicle. The proposed algorithm generates a partial top-view image for a small ROI (region of interest) designated on the top-view space form the image acquired by the camera, detects lanes on the small partial top-view image, and makes a decision on the lane departure by checking overlap between the pre-assigned virtual vehicle and the detected lanes. The proposed algorithm also includes the removal of lines occurred by road symbols (noises) disturbing the lane departure detection between lanes and the prediction of lost lanes using lane information of previous fames. In lane departure detection test using real road videos, the proposed algorithm makes the right decision of 99.0% in lane keeping conditions and 94.7% in lane departure conditions.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.11
• /
• pp.2758-2764
• /
• 2015

In the field of electronic warfare applications, high voltage power supply(HVPS) for high power phased array transmitters must necessarily have an independent operating characteristics for driving mini TWTs. TWT independent operational characteristics, in order to run without interrupting the electronic warfare mission by maintaining the partial transmission function even when one of the TWT has occurred a failure, is known to be very important. In this paper, we describe the research on high-speed independent control system using a high-density HVPS, including FE modulators, hardware configuration and the FPGA in order to independently operate mini TWTs. Also, we have simulated some possible faults in phased array transmitters, and presents the test results to control a faulted TWT independently.