• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.21 no.11
• /
• pp.1950-1956
• /
• 1997

An engineering goal in vibration and noise professionals is to develope quiet machines at the preliminary design stage, and various numerical techniques such as FEM, SEA or BEM are one of the schemes toward the goal. In this paper, the research has been focused on the sensitivity effect of mesh sizes for FEM application so that the optimum size of the mesh that leads to engineering solution within acceptable computing time could be generated. In order to evaluate the mesh size effect, three important parameters have been examined : natural frequencies, number of modes and driving point mobility. First, several lower modes including the fundamental frequency of a 2-D plate structure have been calculated as mesh size changes. Since theoretical values of natural frequencies for a simple structure are known, the deviation between the numerical and theoretical values is obtained as a function of mesh size. The result shows that the error is no longer decreased if the mesh size becomes a quarter wavelength or smaller than that. Second, the mesh size effect is also investigated for the number of modes. For the frequency band up to 1.4 kHz, the structure should have 38 modes in total. As the mesh size reaches to the quarter wavelength, the total count in modes approaches to the same values. Third, a mobility function at the driving point is compared between SEA and FEM result. In SEA application, the mobility function is determined by the modal density and the mass of the structure. It is independent of excitation frequencies. When the mobility function is calculated from a wavelength to one-tenth of it, the mobility becomes constant if the mesh becomes a quarter wavelength or smaller. We can conclude that dynamic parameters, such as eigenvalues, mode count, and mobility function, can be correctly estimated, while saving the computing burden, if a quarter wavelength (.lambda./4) mesh is used. Therefore, (.lambda./4) mesh is recommended in structural vibration analysis.

• Journal of Mechanical Science and Technology
• /
• v.17 no.8
• /
• pp.1148-1155
• /
• 2003

The finite element method is one of the methods widely applied for predicting vibration in mechanical structures. In this paper, the effect of the mesh size of the finite element model on the accuracy of the numerical solutions of the structural vibration problems is investigated with particular focus on obtaining the optimal mesh size with respect to the solution accuracy and computational cost. The vibration response parameters of the natural frequency, modal density, and driving point mobility are discussed. For accurate driving point mobility calculation, the decay method is employed to experimentally determine the internal damping. A uniform plate simply supported at four corners is examined in detail, in which the response parameters are calculated by constructing finite element models with different mesh sizes. The accuracy of the finite element solutions of these parameters is evaluated by comparing with the analytical results as well as estimations based on the statistical energy analysis, or if not available, by testing the numerical convergence. As the mesh size becomes smaller than one quarter of the wavelength of the highest frequency of interest, the solution accuracy improvement is found to be negligible, while the computational cost rapidly increases. For mechanical structures, the finite element analysis with the mesh size of the order of quarter wavelength, combined with the use of the decay method for obtaining internal damping, is found to provide satisfactory predictions for vibration responses.

• Journal of Institute of Control, Robotics and Systems
• /
• v.19 no.1
• /
• pp.40-44
• /
• 2013

The ball-shaped mobile robot, so called ballbot has single point contact on ground and low energy consumption in motion because of the reduced friction. In this paper, a new ballbot is presented, which has omnidirectional mobile platform inside of it as a driving system. Thus the ballbat has omnidirectional mobility without nonholonomic constraints. Kinematics and inverse kinematics of the ballbat is derived also in this paper.

• Proceedings of the KSR Conference
• /
• 1998.11a
• /
• pp.522-529
• /
• 1998

In this study, system analysis for a train vehicle with an articulated bogie frame adopted in TGV and TGV-K system is performed. System analysis is carried out as follows. First, modal analysis of each subsystem is performed to obtain the natural frequencies and mode shapes. Then modal analysis, of a whole vehicle is performed to obtain the potential interaction between the subsystems. Finallyforced response analysis, such as driving point mobility, is performed to obtain the dynamic response of specific points.

• Journal of the Ergonomics Society of Korea
• /
• v.35 no.1
• /
• pp.11-27
• /
• 2016

Objective: The purpose of this study was to develop and evaluate high technology adaptive driving controls, such as mini steering wheel-lever system and joystick system, for the people with physical disabilities in the driving simulator. Background: The drivers with severe physical disabilities have problems in operation of the motor vehicle because of reduced muscle strength and limited range of motion. Therefore, if the remote control system with driver-by-wire technology is used for adaptive driving controls for people with physical limitations, the disabled people can improve their quality of life by driving a motor vehicle. Method: We developed the remotely controlled driving simulator with drive-by-wire technology, e.g., mini steering wheel-lever system and joystick system, in order to evaluate driving performance in a safe environment for people with severe physical disabilities. STISim Drive 3 software was used for driving test and the customized Labview program was used in order to control the servomotors and the adaptive driving devices. Thirty subjects participated in the study to evaluate driving performance associated with three different driving controls: conventional driving control, mini steering wheel-lever controls and joystick controls. We analyzed the driving performance in three different courses: straight lane course for acceleration and braking performance, a curved course for steering performance, and intersections for coupled performance. Results: The mini steering wheel-lever system and joystick system developed in this study showed no significant statistical difference (p>0.05) compared to the conventional driving system in the acceleration performance (specified speed travel time, average speed when passing on the right), steering performance (lane departure at the slow curved road, high-speed curved road and the intersection), and braking performance (brake reaction time). However, conventional driving system showed significant statistical difference (p<0.05) compared to the mini steering wheel-lever system or joystick system in the heading angle of the vehicle at the completion point of intersection and the passing speed of the vehicle at left turning. Characteristics of the subjects were found to give a significant effect (p<0.05) on the driving performance, except for the braking reaction time (p>0.05). The subjects with physical disabilities showed a tendency of relatively slow acceleration (p<0.05) at the straight lane course and intersection. The steering performance and braking performance were confirmed that there was no statistically significant difference (p>0.05) according to the characteristics of the subjects. Conclusion: The driving performance with mini steering wheel-lever system and joystick control system showed no significant statistical difference compared to conventional system in the driving simulator. Application: This study can be used to design primary controls with driver-by-wire technology for adaptive vehicle and to improve their community mobility for people with severe physical disabilities.

• Korean Journal of Computational Design and Engineering
• /
• v.19 no.4
• /
• pp.316-323
• /
• 2014

This paper proposes the 3D modeling and simulation technique for predicting the integrated performance of combat vehicle. To consider the practical driving and firing condition of a combat vehicle, the full vehicle model, which can define the six degrees-of-freedom of vehicle motion and various firing angles, is developed. The critical design parameters such as the stiffness and damping coefficient of suspension system are applied to construct the analysis model of vehicle. A simple ballistic model, which incorporates the empirical interior ballistic model and the point mass trajectory model, is built to estimate the firing range and the firing recoil force. To predict the integrated performance and analyze the effect of system parameters, MATLAB/SIM-ULINK model of a combat vehicle for performing the real time simulation is also developed. Several simulation tests incorporating the road bump and the firing recoil force are presented to confirm the effectiveness of the proposed vehicle model.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.126.2-126
• /
• 2001

This paper, the integration of driving simulator and unmanned vehicle by means of new concept for better performance through a tele-operated system is suggested. But autonomous system is one of the most difficult research topics from the point of view of several constrains on mobility, speed of vehicle and lack of environmental information. In these days, however, many innovations on the vehicle provide the appropriate automatic control in vehicle subsystem for reducing human error. This tendency is toward to the unmanned vehicle or the tele-operated vehicle ultimately. This paper describes the motion system ...

• Proceedings of the KIEE Conference
• /
• 2007.10a
• /
• pp.345-346
• /
• 2007

This paper deals with design of a cube-style modular robot. The modular robot can change its own form according to the working environment. Therefore it is suitable to work in the search and rescue area with the shape of snake, legged robot and humanoid robot. Each of modular unit has to install its own controller on the body and driving mechanism in order to give it mobility autonomously. And also they should attach and detach each other with docking mechanism and algorithm. Using this mechanism, they can make union, separation, recombination. The other important point is that some information of each cell should be exchanged to reconfigure their shape and to make some docking of the modular cell. In this paper we suggested a design concept of our modular robot focused on the docking mechanism of the robot.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.4
• /
• pp.13-27
• /
• 2021

In this study, the impact of traffic flow on the market penetration rate of autonomous vehicles(AV) was analyzed using the data for the year 2020 of the Yongin IC~Yangji IC section of Yeongdong Expressway. For this analysis, a microscopic traffic simulation model VISSIM was utilized. To construct the longitudinal control of the AV, the Intelligent Driver Model(IDM) was built and applied, and the driving behavior was verified by comparison with a normal vehicle. An examination of the study results of mobility and safety according to the market penetration rate of the AV, showed that the network's mobility improves as the market penetration rate increases. However, from the point of view of safety, the network becomes unstable when normal vehicles and AVs are mixed, so there should be a focus on traffic management for ensuring safety in mixed traffic situations.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.21 no.5
• /
• pp.28-41
• /
• 2022

A road system with CV(Connected Vehicle)s, which is often referred to as a cooperative intelligent transportation system (C-ITS), provides various road information to drivers using an in-vehicle warning system. Road environments with CVs induce drivers to reduce their speed or change lanes to avoid potential risks downstream. Such avoidance maneuvers can be considered to improve driving behaviors from a traffic safety point of view. Thus, empirically evaluating how a given in-vehicle warning information affects driving behaviors, and monitoring of the correlation between them are essential tasks for traffic operators. To quantitatively evaluate the effect of in-vehicle warning information, this study develops a method to calculate compliance rate of drivers where two groups of speed profile before and after road information is provided are compared. In addition, conventional indexes (e.g., jerk and acceleration noise) to measure comfort of passengers are examined. Empirical tests are conducted by using PVD (Probe Vehicle Data) and DTG (Digital Tacho Graph) data to verify the individual effects of warning information based on C-ITS constructed in Seoul metropolitan area in South Korea. The results in this study shows that drivers tend to decelerate their speed as a response to the in-vehicle warning information. Meanwhile, the in-vehicle warning information helps drivers to improve the safety and comport of passengers.