• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.20 no.2
• /
• pp.153-159
• /
• 2010

This work focuses on finding a method to reduce the noise of a hermetic reciprocating compressor during start-up using an acoustical analysis. The noise of compressor during start-up, which is a higher level than that of a normal operating condition, has transient and non-stationary characteristics. The acoustical analysis of compressor cavity is performed to find an effective method to reduce the noise level. In the acoustical analysis, the shape variations of frequency response function in the neighborhood of resonances are tested for three parameters: the height of remained oil, the suction position of refrigerant and the position of driving part. As a conclusion of this result, to reduce the emission noise of compressor during start-up, the height of remained oil should be kept at 16 mm, the refrigerant should be sucked at the cross point of nodal lines of X and Y directional cavity modes, and the driving part should be positioned in the center of cavity.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.04b
• /
• pp.195-198
• /
• 2004

In this paper, the disk-type piezoelectric transformer for the high power was investigated with the variation of road resistance. The diameter and thickness of a disk-type piezoelectric transformer was 50mm and 4.5mm, respectively. The piezoelectric transformer was composed to PZT-PMN-PSN. The ratio of driving electrode and generating electrode ranges from 1.4:1 to 3:1. The poling direction of driving part and generating part are the same. A voltage step-up ratio increased with increasing the load resistance, $R_L$, so it reached 60 times under no road resistance. also, the maximum efficiency of 97% was obtained.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.565-570
• /
• 2008

Recently, the intelligent service robot is applied for the purpose of guiding the building or providing information to the visitors of the public institution. The intelligent robot which is on development has a sensor to recognize its location at the bottom of it. Four wheels which are arranged in the form of a lozenge support the weight of the components and structures of the robot. The operating environment of this robot is restricted at the uneven place because the driving part and internal structure is designed in one united body. The impact from the ground is transferred to the internal equipments and structures of the robot. This continuous impact can cause the unusual state of the precise components and weaken the connection between each structural part. In this paper, a suspension system which can be applied to the intelligent robot is designed. The dynamic model of the robot is created, and the driving characteristics of the actual robot and the robot with suspension are compared. The road condition which the robot can operate is expanded by the application of the suspension system. Additionally, the suspension system is optimized to reduce the impact to the robot components.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.147-153
• /
• 2012

The demands of the large scale machine tools, for instance, such as planomiller, turning machine, boring machine, NC machine, have been gradually increased in recent years. As the performances of machine tools and/or cutting tools are advanced, it is possible to perform high-speed and high-precision cutting works. The effective treatment of wet chip, which is discharged from cutting works, becomes very important problems. Therefore, this study is forced on the design of large scale machine tools using CATIA V5R18 and analysis of cutter, which is considered as essential equipment in large scale machine tools, using MSC.Nastran & MSC.Patran. Especially, the relations between tolerated load of cutter, driving horse power and rpm of driving shaft in chip processing system are investigated through analysis. As the results, the reliability of design could be improved by evaluating simulated numerical values, it showed that tolerated loads of supported part and edged part of cutter are 87,000N and 14,450N, respectively.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.20 no.5
• /
• pp.18-34
• /
• 2021

Pedestrian deaths in Korea due to traffic accidents are 40 percent of the fatalities in traffic accidents, which is about twice the average of OECD member countries. To reduce severe pedestrian accidents, it is necessary to apply the accident reduction measures to high-risk drivers (novice, elderly, and commercial vehicle drivers) who are more likely to cause traffic accidents than general drivers. Therefore, this study analyzed the effect of safe driving education on high-risk drivers' behavior. Here, the safe driving education is chosen as the measure to reduce traffic accidents. As part of the study, sudden pedestrian crossing situations were implemented in the driving simulator, and the vehicle trajectory data were collected to compare the driving behavior before and after the education. Most surrogate safety measures showed no improvement in the driving behavior of novice and elderly drivers, and the effect of safe driving education was found to be significant only in the group of commercial vehicle drivers. The results implied that additional measures such as pedestrian safety infrastructure and driver assistance systems, apart from the safe driving education, may be needed for novice and elderly drivers to reduce pedestrian accidents caused by them. With the findings mentioned above, this study is expected to provide a foundation to establish a plan to reduce pedestrian accidents caused by high-risk drivers.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.9 no.1
• /
• pp.29-34
• /
• 2008

We fabricated the 4 channel wave function generator with variable frequency, pulse width, amplitude and rising/falling slope to develop driving method of charged particle type display. The selective sell driving is ascertained by fabricated panel with black and yellow particles. To measure CIE point, reflectivity, contrast ratio and viewing angle, experimental apparatus is integrated with optical circular$(1^{\circ})$ moving emitting/receiving part and spectrometer connected to emitting part. The yellow particles in glass have reflectivity of $35{\sim}40%$ and wavelength of 571.2nm and black one has reflectivity of $15{\sim}20%$ in case of only 1 layer of particle, and the case of 3 layer the optical property is promoted.

• 연구논문집
• /
• s.30
• /
• pp.101-110
• /
• 2000

Weft insertion mechanism is for completing the structure of yarn and weft yarn and its driving method is screw type. In the high speed rapier loom, weft yarn is thrown by insert rapier and carrier rapier into the shed which make divide two parts of upper part ant lower part for warp yarn. It is possible for this mechannism to reduce the size of rapier and wheel, and directly connected to the main shaft without gear belt. Therefore, exact rapier motion through realization of arbitrary acceleration diagram requested rapier and optimal design for high speedization and operating rate increasing are necessary. In this study, with a view to exact system analysis for understanding of overall trace and high speedization of rapier loom through computer simulation. we report not only deduction of displacement, velocity, and acceleration components of rapier for analysis theory establishment, of weft insertion mechanism and exact motion induction according to screw rotation, but also development of simulation program for realization these on the monitor.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.18 no.2
• /
• pp.129-143
• /
• 2019

As the importance of autonomous vehicle safety is emphasized, the application of ISO-26262, a development verification guideline for improving safety and reliability, and the safety verification of autonomous vehicles are becoming increasingly important, in particular, SAE standard level 3 or higher level autonomous vehicles detect and decision the surrounding environment instead of the human driver. Therefore, if there is and failure or malfunction in the autonomous driving function, safety may be seriously affected. So autonomous vehicles, it is essential to apply and verity the safety concept against failure and malfunctions. In this study, we study the fault injection scenarios for safety evaluation and verification of autonomous vehicles using ISO-26262 part3 process and STPA were studied and safety measures for safety concept design were studied through simulation bases fault injection test.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.5
• /
• pp.103-110
• /
• 2020

Bio-inspired underwater robots have been studied to improve the dynamic performance of fins, such as swimming speed and efficiency, which is the most basic performance. Among them, bio-inspired soft robots with a compliant tail fin can have high degrees of freedom. On the other hand, to improve the driving efficiency of the compliant fins, the stiffness of the tail fin should be changed with the driving frequency. Therefore, a new type of variable stiffness mechanism has been developed and verified. This study, which was inspired by the anatomy of a real dolphin, assessed a process of designing and manufacturing a robotic dolphin with a variable stiffness mechanism. By mimicking the vertebrae of a dolphin, the variable stiffness driving part was manufactured using subtractive and additive manufacturing. A driving tendon was placed considering the location of the tendon in the actual dolphin, and the additional tendon was installed to change its stiffness. A robotic dolphin was designed and manufactured in a streamlined shape, and the swimming speed was measured by varying the stiffness. When the stiffness of the tail fin was varied at the same driving frequency, the swimming speed and thrust changed by approximately 1.24 and 1.5 times, respectively.

• Physical Therapy Korea
• /
• v.10 no.2
• /
• pp.71-84
• /
• 2003

The purpose of this study was to provide information on driving characteristics in persons with spinal cord injury through basic statistic analysis of the survey results. The survey was administered to 44 drivers with spinal cord injury. The subjects' general, neurologic and driving characteristics were analyzed, as well as the degree of difficulty in using their vehicles between tetraplegia and paraplegia. The results were as follows: thirty-five (79.6%) of forty-four respondents was men. The average age was 35.0 years old and the age at the time of injury was 29.0 years old. Their neurologic characteristics were tetraplegics 12 (27.3%) and paraplegics 32 (72.2%). Among complete lesions, the highest level those who could drive independently was C7. All the vehicles were equipped with special devices, including "power steering", "automatic transmission" and "hand controls". The vehicles for cervical cord injury were equipped with "grip bars" as well as for the degree of difficulty in using their vehicles, all the subjects felt that "moving the wheelchair in and out of their vehicles" was too difficult for them to do. We suggest that the driver training should be an essential part of the rehabilitation program for patients with spinal cord injuries to maximize their mobility in the community. This training seems to be essential in order to modify the standards of the Handicapped Drivers Ability Test and to aid the driver rehabilitation program in the health insurance payment system. Also, the driver rehabilitation training program should include instruction in that moving wheelchairs in and out of vehicles.