• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.2276-2279
• /
• 2011

The AUTS(Advanced Urban Transit System) are developed by government R&D business. This units are under main line performance test in Daebul test line. Both AC and DC could apply to the AUTS for pantagraph voltage. So main transformer and some high voltage filters are added to the under-frame. As a result the total weight of each car(Mc1-Tp1-M-T-Tp2-Mc2) is different. And axle load is different each other. The main characteristics of AUTS(Advanced Urban Transit System) are as follows. One inverter control one motor, DDM(Dircet Drive Motor), no driving gear, plug no end door, self-steering bogie etc. These matters could be appeared to strange vibration. So vibration test is important. The vibration test performed to Mc1 and Tp1. The results were checked to the up-down direction and left-right direction for acceleration.

• 대한기계학회논문집A
• /
• 제22권3호
• /
• pp.654-662
• /
• 1998

Shift quality of an automatic transmission in a vehicle is mainly affected by transient pressures in the hydraulic system during shifting. In this study, dynamic modelings of the hydraulic system and the power train of an automatic transmission are made systematically by a bond-graph method. The dynamic characteristics of the line pressures and clutch/brake pressures during shiftings are investigated by simulations and verified by experiments. The effects of clutch/brake pressures on the shift torque are also investigated through driving simulation.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.73-85
• /
• 1997

An automatic transmission is an important element of automotive power systems that allows a driving convenience. Compared to a manual transmission, however, it has a few problems in efficiency, shift feel, and maintenance. To improve these, it is imperative to understand the dynamics of automatic transmissions. This paper develops a dynamically-correct model of an automatic transmission, using the bond graph method. The bond graph method is ideally suited for modeling power systems, because the method is based on generalized power variables. The bond graph method is capable of providing correct dynamic constraints and kinematic constraints, as well as the governing differential equations of motion. The bond graph method is applied to 1-4 in-gear ranges, as well as various upshifts and downshifts of an automatic transmission, which allows an accurate simulation of an automatic transmission. Conventional automatic transmission models have no dynamic constraint, which do not allow correct simulation studies.

• 한국정밀공학회지
• /
• 제23권1호
• /
• pp.166-173
• /
• 2006

This paper investigated strength of a bogie frame for Korean tilting train that is being developed in KRRI. In this study, static load tests based on Japanese Industrial Standard (JIS) were performed. In order to simulate vertical and lateral components generated by tilting link mechanism, four hydraulic actuators were used. The eight load cases such as vertical, lateral, traction, braking and driving gear loads were applied for evaluation of the strength of bogie frame. The stresses measured at the stress concentration points were assessed using Goodman diagram. From the experimental results, structural safety of the bogie frame could be ensured.

• 한국공작기계학회논문집
• /
• 제11권2호
• /
• pp.87-94
• /
• 2002

In domestic industry, there is no manufacturers specialized in the production of cutting tools for the difficult cutting materials. Then, we have flew data about them. In this study, the gear driving high speed lathe on which is mounted by a tool dynamometer and high speed CCTV were used to measure the various machining characteristics. Relations among the cutting speed, feed rate per revolution, cutting depth, cutting forces and surface roughness ware graphically analyzed under 64 cutting conditions. The process of chip, i.e., generation, development and falling-off also were visualized for the characterization of chip shapes of the difficult-to-cut materials using the CCTV.

• 대한기계학회논문집
• /
• 제18권11호
• /
• pp.2817-2824
• /
• 1994

A torque split type multi-pass CVT(MPC) system consiting of CVT and planetary gear train with 4 clutches was suggested to overcome the inherent inferior acceleration performance of CVT. Also, a shifting algorithm of MPC was suggested for the two driving modes : (1) power mode and (2) economy mode. By using the shifting algorithm and the MPC vehicle dynamic model, numerical simulations were performed to estimate the performance of the MPC vehicle. Simulation results showed that comparing the performance of the conventional 4-speed automatic transmission, an improvement in acceleration can be obtained by MPC for the power mode and 31% improvement in fuel economy for the economy mode.

• 한국기계가공학회지
• /
• 제9권3호
• /
• pp.19-27
• /
• 2010

Cylinder block is driven by tapered piston for bent-axis type piston pump, so that geometrical mechanism is very complicate. Piston rod must have not separated from shaft when shaft and piston rod is assembled. For this reason, shaft design is changed. Finite element analysis is performed for analyzed structural stability and flexible dynamic behavior. The result of the analysis, maximum equivalent stress occurred under yield stress, therefore structural stability is satisfactory. and flexible dynamic analysis give useful information about driving gear. These background data is avail of manufacture of piston pump.

• 한국생산제조학회지
• /
• 제8권1호
• /
• pp.150-157
• /
• 1999

In this study, the loader was completed that has 4-wheel gear driven drivetrain of study (Ⅰ), the 4-wheel steering with power wheel type, all-wheel traction system, and joy-stick type lever for hydraulic control valve. From driving test of the developed 4WD and 4WS type loader, we obtained that the minimum circling radius and the necessary width in circling motion reduced about 40% and 33% compared with 2WS type loader. Also, all-wheel traction system could keep the tires glued to the ground with greater stability, the power steering allowed a smoother operation, and the joy-stick type lever offered easily to control. Thus, the developed loader having these functions was very fit in a small cattle shed or rugged ground.

• 한국생산제조학회지
• /
• 제20권4호
• /
• pp.376-381
• /
• 2011

CVT(Continuously Variable Transmission) is one of the most promising candidates for the future automobile transmission because of its continuously variable gear ratio and reduced shift shock. It is also possible to operate the power source at its high efficiency region with CVT. The CVT system consists of thrust plate, driving pulley, belt, driven pulley, and preload spring of output shaft. In this paper, the dynamic modeling of a CVT system is completed to obtain the static performances of CVT system. A simulator is implemented on Matlab(Simulink), which can analyse the static performances of a CVT system. The methods for improving the total efficiency of a motorcycle system are also proposed based on the simulation results. In this study we increase the capacity factor of CVT up to the three times of default specification.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1995년도 추계학술대회 논문집
• /
• pp.350-354
• /
• 1995

The Tension Leveller of Cold Rolling Mill In POSCO performs levelling the strip in high speed line. But minor variations in operating condition of driving machines such as motor, gear box, and support bearings, a small gap-variation of supporter and strip slip by poor roll revolutions can cause serious problems in the quality of strip. In this study, firstly, A condition monitoring standard for each sensor is made through with the detail analysis of vibration and strip slip. Secondly, An automatic monitoring and diagnosing system was developed to monitor the condition of Tension Leveller, and diagnose the cause of abnormal condition. Finally, A diagnosing algorithm for abnormal condition and man-machine interface (MMI) for easy operation are developed.