• Transactions on Electrical and Electronic Materials
• /
• 제13권4호
• /
• pp.212-214
• /
• 2012

Both the electrically positive and negative particles in a cell of quick response-liquid powder display (QR-LPD) are surrounded by conductive electrodes on the upper and lower substrate and the dielectric materials of the barrier ribs. Particles in a cell are attached to or detached from the other materials by image force, electric field, Coulomb's force, and Van der Waals' force. Through these forces, the moving particles form an image but induce clumping phenomena. Particles having a large kinetic energy by a large q/m value crash into the opposite electrode with high speed at a large driving voltage and quickly lose electrically charged material. As a result, these particles are clumped and degrade panel performance. The clumped particles in a cell are observed by microscopic photographs and ascertained by a response time. When the bias voltage is increased to 0.68-0.76 $V/{\mu}m$, particle clumping occurs abruptly and the response time increases sharply. This particle clumping is similarly observed after the number of driving times at the driving voltage (0.42-0.64 $V/{\mu}m$).

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2007년도 하계학술대회 논문집
• /
• pp.340-342
• /
• 2007

This paper presents the grip force control of myoelectric hand prosthesis according to myoelectric signal generated in the human muscle. The control system consist of a controller for driving DC motor, torque sensor for measuring out torque of motor, slip sensor for detecting slip of torque. The experimental results proved the reliability of proposed control system.

• 한국자동차공학회논문집
• /
• 제24권6호
• /
• pp.635-641
• /
• 2016

Regenerative braking performance of an electrically powered vehicle is closely related to driving distance per battery charge. An electric vehicle uses appropriate amounts of mechanical braking force and electromagnetic regenerative braking force to recover energy and increase driving efficiency. In particular, when it drives on a downhill road, energy recovery rate is maximized through regenerative braking during coasting based on the mass inertia of the vehicle. Since an electric two-wheeled vehicle covered in this paper is lighter than an electric four-wheeled vehicle, the improvement of its driving distance per battery charge through regenerative braking is different from an electric four-wheeled vehicle. This study compared the driving characteristics of an electric two-wheeled vehicle based on regenerative braking. Two driving test modes were simulated with a chassis dynamometer system. By analyzing the measurement of a chassis dynamometer, the driving characteristics of a two-wheel electric vehicle, such as driving efficiency, were analyzed. In addition, test results were reviewed to draw the limitations of conventional test methods for regenerative braking performance of an electric two-wheel vehicle.

• 한국자동차공학회논문집
• /
• 제4권2호
• /
• pp.198-208
• /
• 1996

The plunge joints of C.V. Joint for vehicle tend to produce a cyclic axial disturbance at a frequency of three of six times shaft speed, in which this distrubance caused by internal frictional effect is related to joint angle, rotational speed, torque, and joint size. This principal axial thrust force might make vehicle shuddered when coinciding with vehicle frequency of tranverse direction, and be one of reasons to have driver feel uncomfortable, unesay, while driving vehicle. The paper makes analysis of axial thrust force & vehicle shudder through computer simulation, comparing the result with experimental data, and reviewing the effect by changing of variables such as dimensions and driving conditions.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 하계학술대회 논문집 D
• /
• pp.2423-2425
• /
• 2004

Mobility of an indoor wheeled robot is affected by adhesion force that is related to various floor conditions. When the adhesion force between driving wheels and the floor decreases suddenly, the robot has slip state. First of all, this paper models adhesion characteristics and slip in wheeled robot. Secondly, the paper proposes estimation method of adhesion force coefficient(AFC) according to slip velocity. In order to overcome this slip problem, optimal slip velocity must be decided for stable movement of wheeled robot. The paper proposes an anti-slip control system based on an ordinary disturbance observer, that is, the re-adhesion control is achieved by reducing the driving torque enough to give maximum adhesion force coefficient. fuzzy logic controller(FLC) is petty useful with slip through that compare fuzzy with PI control for the controller performance. These procedure is implemented using a Pioneer 2-DXE parameter.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2008년도 제39회 하계학술대회
• /
• pp.1197-1198
• /
• 2008

There have been few papers using finite element method(FEM) to analyze arc driving force for spiral type vacuum interrupter electrode up to date while there have been many papers dealing with AMF type electrode by means of FEM. AMF analysis is very important in AMF type electrode because it has proportional relation with effective area which means the area of magnetic flux density above critical magnetic flux density to diffuse arc. In the same manner, arc driving force is an important factor to drive arc by Lorentz force. In this paper two models were calculated and compared by using commercial FEM software Maxwell 3D.

• 전기학회논문지
• /
• 제57권12호
• /
• pp.2202-2207
• /
• 2008

Bearingless SRM(Switched Reluctance Motor) is researched for high speed or special applications which can not use mechanical bearing such as bio pump. In this paper, a novel hybrid pole bearingless SRM is presented. The proposed hybrid pole bearingless SRM has salient poles for torque and suspending force production. Motor torque is controlled by the phase currents in torque pole windings, and the suspending force is controlled by suspending currents in four suspending windings for radial direction suspension. Because the proposed bearingless SRM has divided pole structure, mutual effects between torque current and suspending current are very lower than the conventional one's. From this structure, the number of power devices for power converter can be reduced for bearingless SRM driving. The proposed hybrid pole bearing less SRM is verified by the FEM analysis and experimental results.

• International Journal of Precision Engineering and Manufacturing
• /
• 제8권2호
• /
• pp.85-89
• /
• 2007

Linear ball guideways have been used recently in precision or ultra-precision positioning devices. However, when the inner balls begin to roll or the moving direction reverses, these guideways are subject to rolling friction or nonlinear spring behavior. An ultra-precision device with a linear motor, referred to as a 'tunnel actuator' (TA), has been constructed to measure these phenomena. The application of a TA is beneficial for two reasons: it mostly cancels the attractive magnetic force between the stator and mover (armature), and its magnetic flux leakage is very low. The influence of the nonlinear spring behavior in ball guideways was investigated in this study using the pure driving force from a TA. The equilibrium between the driving force from the TA and the nonlinear spring force provided great accuracy for a positioning stage using a linear ball guideway.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1993년도 하계학술대회 논문집 B
• /
• pp.731-735
• /
• 1993

When induction motor is driven with a load commutated inverter, the output part of the inverter must be capacitive. But, in order to be a good load commutation at the low speed range, very large capacitor or force commutated circuit must be used regarding the capacity of motor. This paper proposed the force commutated circuit for driving the motor in case of the installation of capacitor which can be capable of load commutation at the rating speed. The force commutated circuit is operated by the LC resonant circuit, auxiliary source and SCR, and also composed of the commutation circuit which control the interval of the inverse voltage across the inverter.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2003년도 춘계학술대회 논문집
• /
• pp.1034-1037
• /
• 2003

Recently in the field of precision positioning device, the contact-free actuators are gaining focuses with their outstanding performances by eliminating mechanical frictions. Th is paper is about the driving algorithm for contact-free linear actuator. The proposed driving algorithm has similar structure of drives of switched reluctance motor and reduces the normal forces and force ripple. The simulation and experiment are executed to verify the proposed method.