• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2009년도 춘계학술대회 논문집 에너지변화시스템부문
• /
• pp.149-151
• /
• 2009

Hybrid electric vehicle has three operating mode, depending on the operation of the engine and electric motor. According to the speed range of BLDC motor, In hybrid traction mode, both the engine and electric motor deliver to drive train. Battery charge mode, the electric motor operates as generator and is driven by the engine to charge the batteries. In engine alone traction mode, the electric motor is do-energized, and vehicle is propelled by the engine alone. we propose hysteresis current control technique to maintain constant speed in the motor load torque at the reverse direction. The proposed method is verified by using Matlab Simulink software.

• 전력전자학회논문지
• /
• 제2권1호
• /
• pp.39-45
• /
• 1997

초고속 전동기 구동 시스템을 위하여 간접 신경회로망 제어기를 제안하였다. 고속의 가변 전동기구동에서의 속도응답은 긴 정착시간과 높은 오버슈트의 영향에 있게 되므로 고성능을 위하여 신경회로망 제어기와 신경회로망 에뮬레이터로 구성된 제어기를 사용하였으며, 신경회로망 에뮬레이터는 고속 전동기의 정수와 특성을 동정하는데 사용하였고, 제어기의 학습은 접속강도가 백프로퍼게이션에 의해 조절되도록 하였다. 그리고 시뮬레이션과 실험을 통하여 제안된 시스템의 특성과 장점을 확인하였다.

• International Journal of Automotive Technology
• /
• 제6권5호
• /
• pp.461-466
• /
• 2005

With the growing traffic density and increasing comfort requirements, the automation of the drive train has gained importance in vehicles. The automatic clutch actuation relieves a driver especially in urban and stop-and-go traffic environments. In this paper, an electro-mechanical actuator for clutch-by-wire (CBW) system is implemented as the first stage for the development of automated manual transmissions. The prototype of the automatic clutch actuator is designed systematically, which is composed of the electric motor, worm and worm wheel, and crank mechanism. A test rig is developed to perform the basic function test for the automatic clutch actuation. The developed prototype is validated by the experimental results performed on the test rig.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2004년도 추계학술대회 논문집 전력기술부문
• /
• pp.17-20
• /
• 2004

This paper presents a modeling and simulation of a grid-connected wind turbine generation system with respect to wind variations and three-phase fault in the system. It describes the modeling of the wind turbine system including the drive train model, induction generator model, and grid-interface model on MATLAB/Simulink. Case studies demonstrate that the pitch angle control is carried out to achieve maximum power extraction for wind speed variations and the duration of a fault on the system influences on the output of the wind turbine generator.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2005년도 춘계학술대회 논문집
• /
• pp.283-286
• /
• 2005

Because CV Joint which is one of the component of automobile power train system communicates high power and performs power steering function, it requires high qualities such as high strength, high toughness and high fatigue resistance. This component undergoes a series of production processes such as forging, machining and heat treatment and required properties for this component depends on plastic deformation and heat treatment heavily. Therefore in this study, in order to these effects on mechanical properties due to plastic deformation and heat treatment we performed heat treatment following plastic deformation and then tensile test.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.69.3-69
• /
• 2001

This paper presents a new approach to the design of cruise control system of a mobile robot with two drive wheel. The proposed control scheme uses a Gaussian function as a unit function in the fuzzy-neural network, and back propagation algorithm to train the fuzzy-neural network controller in the framework of the specialized learning architecture. It is proposed a learning controller consisting of two neural network-fuzzy based on independent reasoning and a connection net with fixed weights to simply the neural networks-fuzzy. The performance of the proposed controller is shown by performing the computer simulation for trajectory tracking of the speed and azimuth of a mobile robot driven by two independent wheels.

• 한국철도학회논문집
• /
• 제20권1호
• /
• pp.43-54
• /
• 2017

본 논문에서는 철도차량 추진시스템을 위한 3-레그 인버터와 5-레그 인버터의 성능을 비교/분석하고 철도차량에 5-레그 인버터를 적용함에 있어 최적의 동작 조건을 제시한다. 5-레그 인버터는 두 대의 3-레그 인버터에 비해 2개의 스위치가 감소되며, 하나의 제어보드로 두 대의 3상 전동기를 독립적으로 제어할 수 있다. 이로 인해 두 대의 3-레그 인버터를 이용할 경우보다 시스템의 비용 감소와 소형화가 가능하다. 본 논문에서는 먼저 도시철도 차량에서 사용중인 유도전동기 제어 기법과 PWM 방법을 분석한다. 다음으로 5-레그 인버터의 기본 동작과 특징을 분석한다. 이러한 분석을 바탕으로 동일한 유도전동기 제어 기법과 PWM 방법을 3-레그 인버터와 5-레그 인버터에 적용했을 때 유도전동기의 속도와 토크 특성을 비교하고 분석한다.

• Journal of Biosystems Engineering
• /
• 제28권3호
• /
• pp.187-198
• /
• 2003

This study was conducted to investigate the effect of design parameters of modulating valve and hydraulic clutch on the shift quality of a power shuttle transmission using a computer simulation. Computer simulation models of a hydraulic control system and a power shuttle drive train were developed and verified by an experimental power train in a laboratory. The software EASY5 was used for the modeling and simulation of the power shuttle transmission. Results of the study were summarized as follows: For a good shift quality. it is required to reduce the transient torque transmitted to the output shaft of the transmission as much as possible. This may be achieved by reducing the modulating time and clutch pressure. It was found that the design parameters most significantly affecting the modulating time and clutch pressure were the spring constant and displacement of a load piston of the modulating valve, and the spring constant and damping of the clutch piston. The modulating time decreased as the spring constant increased and increased as the displacement of the load piston decreased. The transient torque decreased as the modulating time increased. However their relationships were not always linear. As the damping decreased, both the modulating pressure and time decreased, which also resulted in a decrease in the transient torque. The spring constant of the clutch piston affected the modulating time and the peak transient torque. As the spring constant of the clutch increased, the peak transient torque decreased.

• 한국컴퓨터정보학회논문지
• /
• 제19권12호
• /
• pp.187-196
• /
• 2014

본 논문에서는 고정된 역간 거리를 정해진 운전 시분내에 주행에너지를 최소화하며 주행하는 열차의 특성을 파악하고 수학적으로 모델링한다. 도시철도차량 자동주행에 일반적으로 사용되는 PID제어기 대신 목표값에 추종하면서도 자동 주행 중 소비에너지가 최소화되도록 최적제어기를 사용하여 철도 차량를 모델링하였으며 실제 동일한 운행조건하에서 설계한다. 실제 선로 조건을 적용하여 별도의 차상장치나 선로주변시설 없이도 자동운전 중 주행에너지를 최소하여 주행에너지를 절감하고자 한다. 따라서 8호선 실 노선 구간별 운전시분 내에서 실측 데이터 분석을 위해 직선구간/구배구간/곡선구간 등 구간을 선정하고 그 구간에서 열차의 운행패턴에 따라 에너지를 절감하는 열차운행을 방법을 제시하였다.

• Wind and Structures
• /
• 제29권6호
• /
• pp.417-430
• /
• 2019

To study the wake influence of an upstream bridge on the wind-resistance performance of a downstream bridge, two adjacent long-span cable-stayed bridges are taken as examples. Based on wind tunnel tests, the static aerodynamic coefficients and the dynamic response of the downstream bridge are measured in the wake of the upstream one. Considering different horizontal and vertical distances, the flutter derivatives of the downstream bridge at different angles of attack are extracted by Computational Fluid Dynamics (CFD) simulations and discussed, and the change in critical flutter state is further studied. The results show that a train passing through the downstream bridge could significantly increase the lift coefficient of the bridge which has the same direction with the gravity of the train, leading to possible vertical deformation and vibration. In the wake of the upstream bridge, the change in lift coefficient of the downstream bridge is reduced, but the dynamic response seems to be strong. The effect of aerodynamic interference on flutter stability is related to the horizontal and vertical distances between the two adjacent bridges as well as the attack angle of incoming flow. At large angles of attack, the aerodynamic condition around the downstream girder which may drive the bridge to torsional flutter instability is weakened by the wake of the upstream bridge, and the critical flutter wind speed increases at this situation.