• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.25 no.8
• /
• pp.553-558
• /
• 2015

This paper aims at making a dedicated vibration monitoring and diagnosis framework for 3MW WTG(wind turbine generator). Within the scope of the research, vibration data of WTG drive train are used and WTG operating conditions are involved for dividing the vibration data class which included transient and steady state vibration signals. We separate two health detections which are CHD(continuous health detection) and EHD(event health detection). CHD has function of early detection and continuous monitoring. EHD makes the use of finding vibration values of fault components effectively by spectrum matrix subsystem. We proposed framework and showed application for 3MW WTG in a practical point of view.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.19 no.6
• /
• pp.113-118
• /
• 2011

Fuel Cell Hybrid Vehicle (FCHV) is one of the most promising candidates for the next generation of transportation. It has many outstanding advantages such as higher energy efficiency and much lower emissions than internal combustion engine vehicles. It also has the ability of recovering braking energy. In order to design an FCHV drive train, we need to determine the size of the electric motor, the Fuel Cell System (FCS), and the battery. In this paper, the methodology for the sizing of these components is introduced based on the driveability constraints of the FCHV. A power management strategy is also presented because the battery energy capacity depends on it. The warm-up time of the FCS is also considered in the power management strategy and the simulation result is compared to that without considering the warm-up time.

• Journal of Drive and Control
• /
• v.14 no.4
• /
• pp.29-36
• /
• 2017

Electronic control technologies that have long been developed for passenger cars spread to construction equipment and agricultural vehicles because of its outstanding performance achieved by embedded software. Especially, system program of transmission control unit (TCU) plays a crucial role for the superb shift quality, driving performance and fuel efficiency, etc. Since the control algorithm is embedded in software that is rarely analyzed, development of such a TCU cannot be conducted by conventional reverse engineering. Transmission simulator is a kind of electronic device that simulates the electric signals including driver operation command and output of various sensors installed in transmission. Standalone TCU can be run in normal operation mode with the signals provided by transmission simulator. In this research, transmission simulator for the tracked vehicle TCU is developed for the analysis of shift control algorithm from the experiments with standalone TCU. It was confirmed that shift experimental data for the simulator setup conditions can be used for the analysis of control algorithms on proportional solenoid valves and shift map.

• Proceedings of the KSR Conference
• /
• 2011.10a
• /
• pp.545-555
• /
• 2011

Presently, The Regular Block System(Automatic, Interlocking block system) is usually used during the operation of block section. However, In case that the regular block system fails because of the failure of the fixed signals and block equipment or in case of the unexpected emergency which should drive on the single line due to the accidents in the double line section or the repair work of the single line, the Substitute Block System to use the driving permission license(mapping ticket and paper) is used. In case of the operation of the opposite line and the temporary one line, the safety gets worse and the SBS may cause the fatal accidents such as a head-on & a rear-end collision. Also, the unmanned railroad stations has recently increased owing to the effective operation of the stations, for it is difficult to execute the SBS in their absence. As a result, the increase of the operation time made the train delayed. Being on the rise of these problems, in this study, we analyzed the problems and difficulties of the SBS on one line which is lacking stability and safety and on the sections combined between maned and unmaned railroad stations. And we proposed the suitable method in KORAIL referring to the examples of European & Japan railways lately. According to the passing of the high tech time, If the new SBS equipped with stability and safety is executed, it will contribute to the effective operation of trains and the satisfaction of KORAIL customers in the future.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.12 no.4
• /
• pp.119-128
• /
• 2004

With the growing traffic density and increasing comfort requirements, the automation of the drive train will gain importance in vehicles. The automatic clutch actuation relieves the drivers especially in urban driving and stop-and-go traffic conditions. This paper describes the dynamic modeling of a clutch actuator and clutch spring. The dynamic model of the clutch system is developed using MATLAB/Simulink, and evaluated by experimental data using a test rig. This performance simulator is useful to develop the clutch-by-wire (CBW) system for an automated manual transmission (AMT). The electro-mechanical type CBW system is also implemented as an automatic clutch for AMT. The prototype of CBW system is designed and implemented systematically, which is composed of an electric motor, worm gear and slider-crank mechanism. The test rig is developed to perform the basic function test of the automatic clutch, and the developed prototype is validated by the experimental data on the test rig.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.2
• /
• pp.142-149
• /
• 2004

This paper presents a neural network controller of a grid-connected wind energy conversion system for extracting maximum power from wind and a power controller to transfer the maximum power extracted into a utility grid. It discusses the modeling and simulation of the wind energy conversion system with the controllers, which consists of an induction generator, a transformer, a link of a rectifier, and an inverter. The paper describes tile drive train model, induction generator model and grid-interface model for dynamics analysis. Maximum power extraction is achieved by controlling the pitch angle of the rotor blades by a neural network controller. Pitch control method is mechanically complicated, but the control performance is better than that of the stall regulation. The simulation results performed on MATLAB show the variation of the generator torque, the generator rotor speed, the pitch angle, and real/reactive power injected into the grid, etc. Based on the simulation results, the effectiveness of the proposed controllers is verified.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.1
• /
• pp.11-15
• /
• 2011

In this paper, a methodology for the power control of a wind turbine, which is the variable-speed and variable-pitch (VSVP) control system, is introduced. This control methodology maximizes the capability of the turbine to extract maximum power from the wind in the regions with low wind speeds. Further, it regulates the wind-turbine power as the rated power in the case of the regions with high wind speeds. A simple drive train model is used to design the VSVP control system. The methodology for VSVP control is mechanized by controlling the generator torque and blade pitch. Finally, some simulation results for the VSVP control to a MW wind turbine are discussed in this paper.

• Journal of Drive and Control
• /
• v.12 no.3
• /
• pp.18-24
• /
• 2015

The plug-in hybrid electric vehicle has a high fuel economy and can be driven long distances. Its different modes include the electric vehicle, hybrid electric vehicle, and only engine operating mode. A power management strategy is important to determine which mode should be selected. The strategy makes the vehicle more efficient using appropriate power sources for driving. However, the strategy usually needs a driving speed profile which is future driving cycle. If the profile is known, the strategy easily determines which mode is driven efficiently. However, it is difficult to estimate the speed profile for a real system. To address this problem, this paper proposes a new power distribution strategy using a neural network. The average speed and driving range are used as input parameters to train the neural network system. The strategy determines a limit for the use of the battery and the desired power is distributed between the engine and the motor simultaneously. Its fuel economy can increase by improving the basic strategy.

• Journal of the Korean Society for Railway
• /
• v.18 no.3
• /
• pp.175-185
• /
• 2015

Generally, in the train area, switch tracks have required high reliability because this system is directly associated with derailment. Especially, switch tracks of Maglev vehicles must be moved in terms of the whole geometric characteristics, in which the bogies are encased in the switch track. For this reason, switch track was constructed with steel lighter than concrete girders. But, the steel switch track was weak because of structural vibration as well as structural deformation. Therefore, it is important to predict the levitation stability when a vehicle passes over flexible switch track. The aims of this paper are to develop a coupled dynamic model to describe the relationship between a Maglev vehicle and switch track and to predict the levitation stability. In order to develop the coupled dynamic model, a three dimensional vehicle model was developed based on multibody dynamics; a switch model was made using the modal superposition method. And, the developed model was verified using comparison measured data.

• Journal of Cadastre & Land InformatiX
• /
• v.46 no.2
• /
• pp.297-312
• /
• 2016

The current government strives to train those supposed to drive the national economy, and bridge the gap between qualification and industrial sites through competency-based qualification systems, not the educational background. In this regards, the government is planning to adopt the course evaluation qualification system. The course evaluation qualification system, on a basis of the NCS, is a system to qualify certain people completing the education and training fulling a specific requirement for a national technical qualification in case they meet the internally and externally assessed criteria. This can be seen as an attempt to practically link between job training and qualifications. The NCS model and learning module in the cadastral field are already utilized as the training and eduction in the specialized school and colleges. However, the current national technical qualification system is considered as a main system because the course evaluation qualification system has not been introduced yet. This study analyzed the process of the course evaluation qualification system, and conducted a survey to solicit feedback on introduction of course evaluation qualification system, Besides, the NCS evaluation model is presented in order for the introduction of course evaluation qualification system in the cadastral fields.