• 소성∙가공
• /
• 제10권2호
• /
• pp.144-150
• /
• 2001

Tool design is introduced in a multi-stage rectangular cup drawing process with the large aspect ratio. Finite element simulation is carried out to investigate deformation mechanisms with the initial tool design. The analysis reveals that the difference of the drawing ratio and the irregular contact condition produces non-uniform metal flow to cause wrinkling and severe extension. For remedy, the modification guideline is proposed in the design of the tool and process. Analysis results confirm that the modified tool design not only improves the quality of a deep-drawn product but also reduces the possibility of failure.

• 소성∙가공
• /
• 제19권6호
• /
• pp.363-371
• /
• 2010

In ultrasonic vibration drawing, the drawing forces can be reduced by applying ultrasonically oscillating dies. Ultrasonic vibration drawing has been considered as a means of accommodating high-level drawing processes such as shaped wire, ultrafine wire, and the wire drawing operation in semidry or dry condition. Prior studies were attempted to analyze the mechanism of improved drawing performances, such as reduced drawing force and improved lubrication characteristic. However, researches on design rule for ultrasonic vibration drawing system are not yet carried out. The principal objectives of this work are to design a set of tooling capable to superimpose the oscillations and to observe by experiments the influence of the ultrasonic oscillations on the wire drawing.

• 소성∙가공
• /
• 제6권5호
• /
• pp.416-424
• /
• 1997

In the present study, a contact search and check algorithm for general tool surface described by triangular FE patch is proposed. To improve numerical stability, SEAM element using the linear Coons interpolation has been used. To check the proposed algorithm, both clover cup and L-shape cup deep drawing processes are calculated. The computed results shows that the proposed contact algorithm can be successfully applied for sheet metal forming processes with general shaped tools.

• 소성∙가공
• /
• 제16권5호통권95호
• /
• pp.401-405
• /
• 2007

Due to the low densities and high specific strength and stiffness, magnesium alloy sheets are very attractive lightweight materials for automotive and electrical products. However, the magnesium alloy sheets should be usually formed at elevated temperature because of their poor formability at room temperature. For the use of the magnesium alloy sheets for an industrial, their mechanical properties at elevated temperature and appropriate forming process conditions have to be developed. In this study, non-isothermal simulation of a square cup drawing of magnesium alloy sheets have been conducted to evaluate a proper forming process conditions such as the tool temperature, the tool shoulder radius, friction between the blank and the tools. According to this study, appropriate forming process conditions of square cup drawing at elevated temperature from magnesium alloy sheets are suggested.

• 소성∙가공
• /
• 제3권4호
• /
• pp.468-481
• /
• 1994

Mathematical description of arbitrarily-shaped tool surface are introduced by parametric patch approaches along with the related contact search algorithm. In order to maintain the advantages of membrane elements and to incoporate the bending effect, a BEAM(Bending Energy Augmented Membrane) element is proposed. Computation are carried out for some complex axisymmetric multi-stage deep drawing to verify the validity and the effectiveness of the proposed method.

• 소성∙가공
• /
• 제8권5호
• /
• pp.449-453
• /
• 1999

Sheet metal forming process is a non-linearity problem which is affected by various process variables, such as geometric shape of punch and die, frictional characteristic, etc.. Therefore, the knowledge of the influence of the process variables is needed in the design of sheet metal working processes. In this paper, cylindrical cup drawing tests for blank holding force, punch speed and lubrication between sheet material and tool were carried out to investigate the influence upon sheet formability. Experimental results were discussed about the defects on the deformation behaviors during the forming process.

• 소성∙가공
• /
• 제19권4호
• /
• pp.253-262
• /
• 2010

For multi-stage deep drawing process including ironing operation and biaxial forming in this study, tool developments are achieved, and the developed tool sets are applied to experimental investigations. In process and tool designs, a contact condition between intermediate blank and lower die is considered as the sequential one. In this study, the material used is cold-rolled thin sheet (SPCE) with the initial thickness of 0.4mm. From the experimental approaches, several failures such as tearing, localized thickening and thinning, are observed. To solve these failures, the contact surface on the lower die is modified. As the experimental results by applying the modified lower die, it is investigated that the failures are not occurred, and the excessive deformation behavior due to the thinning and thickening effects are decreased. Furthermore, the thickness distributions on the major axis and the minor axis of each intermediate blank are investigated to be already satisfied the target (ironing) thickness, respectively. By this systematic approach, it is confirmed that the experimental results show good agreements with the designed and required configuration of each deformed and final products.

• 한국지리정보학회지
• /
• 제24권4호
• /
• pp.1-25
• /
• 2021

정부는 지하안전사고 대응 및 예방을 위해 현행 수작업 기반의 지하공간통합지도 구축 및 갱신체계를 지하구조물을 포함한 지하정보에 대해서 자동화 기반의 3D 지하정보 구축 및 갱신체계로의 전환을 위한 준공도서제출 시스템 구축사업을 진행하고 있다. 하지만 3D 지하구조물 자동화 갱신 시 필요한 표준도면 연구가 미비하여 이에 관한 구체적인 연구가 필요한 실정이다. 본 논문에서는 지하공간통합지도를 구성하는 6종 지하구조물을 대상으로 표준도 기반의 3차원 지하구조물 구축 방안을 제시하여 신속 정확한 도면데이터 작성과 체계적인 3차원 지하구조물 도면데이터 관리가 이루어질 수 있도록 하였다. 또한, 지하정보 실무에 활용 가능한 3D 구축용 가공도면 툴을 개발하여, 일반 CAD 프로그램 사용자들도 쉽게 가공도면을 제작할 수 있도록 하였다. 본 논문에서 도출된 결과물들은 향후 3D 지하구조물 구축을 위한 표준 프레임워크 및 실무적용 지침 수립 시 주요한 참조자료가 될 것으로 기대한다.

• 소성∙가공
• /
• 제9권3호
• /
• pp.313-319
• /
• 2000

Finite element analysis is carried out for simulation of the multi-stage elliptic cup drawing process with the large aspect ratio. The analysis incorporates with shell elements for an elasto-plastic finite element method with the explicit time integration scheme. For the simulation, LS-DYNA3D is utilized for its wide capability of solving forming problems. The simulation result shows that the non-uniform drawing ratio at the elliptic cross section ad the small shoulder radius cause failure such as tearing and wrinkling. The result suggests the guideline to modify the tool shape for prevention of the failure during the drawing process.

• 소성∙가공
• /
• 제7권6호
• /
• pp.519-529
• /
• 1998

In automotive industries the stamping of laser-welded blank gives many merits which bring about dimensional accuracy, strong body assembly and high productivity. However the welding of blanks with different thickness or/and different strength materials introduces many challenging formability problems for process development and tool design. in this paper the deformation characteristics for deep drawing process of laser-welded blank with different thickness sheets are investigated by experiment as well as by FEM simulation. The blank holding force ratio to avoid the movement of weld line was suggested and compared with the experimental result for cylindrical and rectangular cup drawing process. The optimal location of weld line in laser-welded blank with different thickness sheets is calculated to compensate for the movement of weld line on deep drawing process. In addition the effect of location of weld line on formability is clarified using FEM simulation.