• 한국항공우주학회지
• /
• 제46권1호
• /
• pp.41-51
• /
• 2018

무장 헬리콥터에서 발사되는 무유도 로켓은 로터 블레이드에 의한 내리흐름과 전후좌우 기동으로 인한 외풍에 의해 전체 궤적 및 사거리가 변화하므로, 내리흐름 효과를 고려하여 무유도 로켓의 궤적을 예측하는 것이 중요하다. 내리흐름 효과를 고려한 무유도 로켓의 궤적 및 사거리를 예측하기 위해, 본 연구에서 여러 외풍 조건에 따른 후류 영역을 Actuator Disk Model(ADM)로 계산하고 6 자유도 (6 DOF) 운동 해석으로 무유도 로켓의 자세 및 전체 비행 궤적을 예측할 수 있는 알고리즘을 개발하였다. 개발된 알고리즘은 ADM 해석 결과를 6 자유도에 반영하여 다양한 초기 발사조건에서 무유도 로켓의 전체 궤적을 예측할 수 있고, 기존 Inflow model을 이용한 내리흐름 해석과는 다르게 동체와의 간섭효과를 고려하여 비교적 정확한 내리흐름 및 다양한 외풍 환경 조건으로 궤적을 예측 할 수 있다. 개발된 알고리즘을 이용하여, 내리흐름 효과에 의한 무유도 로켓의 자세 및 궤적 변화 메커니즘을 유효 받음각 변화와 기수 자세 안정성으로 규명하였다. 그리고 외풍으로 인해 변화하는 내리흐름 효과를 고려하여 무유도 로켓의 궤적변화와 사거리를 계산한 결과, 후방 외풍 시 최대 13% 사거리 증가를 보였다. 사거리 증가의 주요 요인으로 내리흐름 영역과 강도, 부차적 요인으로 외풍과 동체와의 간섭효과, 동압의 크기인 것을 밝혔다. 또한 사거리 변화량이 가장 큰 후방 외풍에서, 후방 외풍의 풍속이 증가함에 따라 로켓의 사거리가 증가하였다. 하지만 특정 후방 외풍 크기 이상에서 더 이상 로켓 사거리가 증가하지 않는 한계를 보였다.

• 한국항공우주학회지
• /
• 제45권10호
• /
• pp.817-824
• /
• 2017

꼬리날개 조종 유도무기의 주날개-꼬리날개 간섭 현상에 대한 연구를 수행하였다. 풍동시험 데이터를 이용하여 주날개-꼬리날개 간섭 정도를 산출하였으며 날개간의 간섭 현상이 전체 공력에 미치는 영향을 분석하였다. 성분 시험 결과를 이용하여 downwash angle을 산출하였으며 날개간의 간섭 영향을 받음각에 대한 비율로 나타내었다. 날개간의 간섭현상 발생 시 유동 특성을 살펴보기 위해 수치해석을 실시하였으며 받음각에 대한 vorticity 특성을 비교하였다. 실험적, 수치적 연구를 통해 주날개-꼬리날개 간섭현상이 유도무기의 정안정성에 큰 영향을 미침을 확인하였다.

• 대한기계학회논문집B
• /
• 제25권8호
• /
• pp.1122-1130
• /
• 2001

Film cooling performance from two rows of holes with opposite orientation angles is evaluated in terms of heat flux ratio. The film cooling hole has a fixed inclination angle of 35°and orientation angle of 45°for the downstream row and -45°for the upstream row. Four film cooling hole arrangements including inline and staggered configurations are investigated. The blowing ratio studied was 1.0. Boundary layer temperature distributions are measured to investigate injectant behaviors and mixing characteristics. Detailed distributions of the adiabatic film cooling effectiveness and the heat transfer coefficient are measured using TLC(Thermochromic Liquid Crystal). For the inline configuration, there forms a downwash flow at the downstream hole exit to make the injectant well attach to the wall, which gives high adiabatic film cooling effectiveness and heat transfer coefficient. The evaluation of heat flux ratio shows that the inline configuration gives better film cooling performance with the help of the downwash flow at the downstream hole exits.

• Journal of Biosystems Engineering
• /
• 제35권4호
• /
• pp.215-223
• /
• 2010

In order to develop an precision aerial pesticide application system to be attached to an unmanned helicopter which can be applied to small lots of land, this study analyzed the flowing and spraying characteristics of the spray droplets by the main rotor downwash by setting the application conditions at the flight altitude of 3 m, the diameter of main rotor of 3.1 m, the boom length of around 2.8 m, and the spraying rate of 8 L/ha. The results of this study are summarized below. Through analysis of the covering area ratio of the spray droplets by main rotor downwash by nozzle type, boom with tilt angle and height, it was found that the covering area ratio of the twin flat-fan nozzle of around 25% was more uniform than other types of nozzle, also boom with $10^{\circ}$ tilt angle and spraying height of 3 m was shown to be the appropriate conditions for aerial application of pesticides. It was found that the nozzle position to minimize the scattering loss of spray droplets due to vortex phenomenon at both ends of the main rotor was around 10 cm from the end of the main rotor. An application test for the aerial pesticide application system attached to the HUA-ACEI unmanned helicopter developed by the Rural Development Administration showed that the range of covering area ratio of the spray droplets was 10-25%, and the spraying width was approximately 7 m when over 10% of covering area ratio was considered for valid spraying.

• International Journal of Aeronautical and Space Sciences
• /
• 제10권1호
• /
• pp.20-29
• /
• 2009

There are concerns about the influence of the gust wind caused by helicopters affecting the moving vehicles while hovering over the road during rescue activities. For the understanding of such complicated flow. numerical simulation of a rotor hovering above the ground has been carried out, changing the rotor/ground clearances. The rotor thrust is kept constant. and the rotor control is determined by trim adjustments incorporated into the CFD algorithm. Collective pitch angle and the required power decreases with the rotor/ground clearance which agrees with experience. Changes of the flowfield near the rotor with regard to the rotor height are investigated based on the calculated results.

• 대한기계학회논문집B
• /
• 제26권1호
• /
• pp.82-93
• /
• 2002

The effects of the interaction between the flow and temperature field and a boundary layer due to a variety of the height of a vortex generator are experimentally investigated. The test facility consists of a boundary-layer wind tunnel with the vortex generator protruding from the bottom surface. In order to control the strength of the longitudinal vortices, the angle of attack and the spacing distance of the vortex generator are 20 degree and 40 mm, respectively. The height of the vortex generator (H) is 15 mm, 20 mm and 30 mm and the cord length of it is 50 mm. Three-component mean velocity measurements are made using a 5-hole probe system and the surface temperature distribution is measured by the hue capturing method using thermochromatic liquid crystals. By using the method mentioned above, the following conclusions are obtained from the present experiment. The boundary layer is thinned in the downwash region where the strong downflow and the lateral outflow of the boundary layer fluid occur and thickened in the upwash re,3ion where the longitudinal vortex sweeps low momentum fluid away from the bottom surface. In case that the height of the vortex generator increases, the averaged circulation and the maximum vorticity of the vortex pair decrease. The contours of the non-dimensional temperature show the similar trends fur all the cases (H=15 mm, 20 mm and 30 mm). The peak augmentation of the distribution of the local non-dimensional temperature occurs in the downwash region near the point of minimum boundary-layer thickness.

• 한국항공우주학회지
• /
• 제41권12호
• /
• pp.931-939
• /
• 2013

본 논문에서는 항공기 날개의 개념 설계에서 적용하기에 적합한 양력선 방법을 찾고 정확성과 적용범위를 분석한다. Prandtl의 양력선 이론에서 발전된 두 가지 양력선 방법으로서 얇은 익형의 가정을 갖고 3/4 시위의 제어점에서 속도경계조건을 부여하는 Weissinger방법과 3차원 와류 양력법칙을 적용한 Phillips의 방법을 택하였다. 계산 대상은 타원형 날개, 후퇴각이 있는 날개, 그리고 상반각과 비틀림이 있고 후퇴각 없는 테이퍼 날개이다. 계산을 통해 포텐셜 유동의 공력 데이터로 날개의 순환분포, 내리흐름 분포, 양력과 유도항력을 추출하여 이론식 결과 및 풍동시험 데이터와 비교하였다. Weissinger 방법은 날개의 형상에 상관없이 정확도와 신뢰성 있는 결과를 보여주지만 Phillips 방법은 후퇴각이 있는 날개에서는 부정확한 결과를 나타내었다.

• 대한기계학회논문집B
• /
• 제22권4호
• /
• pp.530-541
• /
• 1998

Heat transfer augmentation in a rib-roughened duct is affected by the rib configurations, such as rib height, angle of attack, shape, rib to rib pitch, and aspect ratio of a duct. These have been the main subjects in studying the average heat transfer and the friction loss of the fully developed flow. Investigating distributions of local heat transfer coefficients and flow patterns in a duct with the rib turbulators is necessary to find the characteristics of heat transfer augmentation and to decide the optimal configurations of ribs. In the present study the numerical analyses and the mass transfer experiments are performed to understand the flow through a rib roughened duct and the heat transfer characteristics with various angles of attack of ribs. A pair of counter-rotating secondary flow in a duct has a main effect on the lateral distributions of local mass transfer coefficients. Downwash of the rotating secondary flow, reattachment of main flow between ribs and the vortices near ribs and wall enhanced the mass transfer locally up to 8 times of that in case of the duct without ribs.

• 대한조선학회논문집
• /
• 제41권5호
• /
• pp.8-13
• /
• 2004

In order to better understand the characteristics of the flow field around the submerged hydrofoil of finite span with high speed and shallow submergence. a numerical code which can solve the flow around a fast lifting body under the free surface was developed and used to obtain various interesting features of the flow. The code was based on the panel method of Hess( 1972), and the free surface condition was linearized to conform with the assumption of the high Froude number. It is shown that the effect of the change of submerged depth. angle of attack and aspect ratio upon the sectional lift coefficient is rather significant for the case of the chosen example wing, which has the rectangular planform. Since Lee(2002)'s theoretical results were for the wing of elliptical planform, the direct comparison of the two results was not possible. It seems that more computational results are in need to compare the theoretical and the numerical prediction in detail.

• 한국가시화정보학회지
• /
• 제18권3호
• /
• pp.69-76
• /
• 2020

In the present study, we investigate the flow separation characteristics of a paraglider canopy model by tuft visualization. The experiment is conducted at Re = 3.3×105 in a wind tunnel large enough to contain the three-dimensional paraglider canopy model, where Re is Reynolds number based on the mean chord length and the free-stream velocity. The flow separation characteristics of the canopy model near the wing root are similar to those of a two-dimensional airfoil with a cross-section similar to the model. On the other hand, near the wingtip region, the flow separation is suppressed by the downwash induced by the wingtip vortex. As a result, as the angle of attack increases, the flow separation occurs from the wing root region of the canopy model and develops toward the wingtip.