• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.33 no.6
• /
• pp.31-38
• /
• 2005

Aerodynamic influence coefficient linearly relates pressure with downwash in panel method for load analysis in which the viscosity of a flow is ignored and the compressibility cannot be taken into account in transonic region. Since the planform of an aerodynamic surface determines the coefficient, the panel method has a limit to the analysis of low Reynolds number flow. The accuracy of the pressure distribution can be improved by a direct correction to the pressure or a correction to the downwash, which is considered the change of camber or thickness, using the aerodynamic coefficients from wind tunnel test as constraints. A premultiplying correction method as well as a postmultiplying correction method is applied to a micro air vehicle to provide more accurate aerodynamic pressure for trim and load analyses. Theoretical aerodynamic pressure is obtained from the panel method. Correction factor matrix and correct pressure coefficient are computed for the conditions with two constraints in addition to single constraint. The postmultiplying correction method gives a better improvement in pressure distribution on micro air vehicle due to the flow characteristics on it.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.26 no.1
• /
• pp.82-93
• /
• 2002

The effects of the interaction between the flow and temperature field and a boundary layer due to a variety of the height of a vortex generator are experimentally investigated. The test facility consists of a boundary-layer wind tunnel with the vortex generator protruding from the bottom surface. In order to control the strength of the longitudinal vortices, the angle of attack and the spacing distance of the vortex generator are 20 degree and 40 mm, respectively. The height of the vortex generator (H) is 15 mm, 20 mm and 30 mm and the cord length of it is 50 mm. Three-component mean velocity measurements are made using a 5-hole probe system and the surface temperature distribution is measured by the hue capturing method using thermochromatic liquid crystals. By using the method mentioned above, the following conclusions are obtained from the present experiment. The boundary layer is thinned in the downwash region where the strong downflow and the lateral outflow of the boundary layer fluid occur and thickened in the upwash re,3ion where the longitudinal vortex sweeps low momentum fluid away from the bottom surface. In case that the height of the vortex generator increases, the averaged circulation and the maximum vorticity of the vortex pair decrease. The contours of the non-dimensional temperature show the similar trends fur all the cases (H=15 mm, 20 mm and 30 mm). The peak augmentation of the distribution of the local non-dimensional temperature occurs in the downwash region near the point of minimum boundary-layer thickness.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.41 no.12
• /
• pp.931-939
• /
• 2013

In this paper, we try to find the lifting-line method which is applicable to the conceptual design of aircraft wings, and analyze the accuracy and coverage of the method. Two methods that are extended from the lifting-line theory of Prandtl are selected. One of the methods is Weissinger's method which imposes the velocity boundary condition at the control points located at the quarter chord, and the other is Phillips's method which combines the three-dimensional vortex lifting law. Calculations are performed for an elliptic wing, a swept back wing, and a tapered unswept wing with dihedral angle and geometric twist. The aerodynamic data of the potential flow such as spanwise distributions of circulation and downwash, lift and induced drag are obtained through calculations, and these data are compared with theoretical results and wind tunnel test data. As a result, Weissinger's method showed good accuracy and reliability regardless of wing shapes, but Phillips's method revealed inaccurate results for a swept back wing.

• Journal of Advanced Marine Engineering and Technology
• /
• v.32 no.1
• /
• pp.100-109
• /
• 2008

The three-dimensional flows in the Weis-Fogh mechanism are studied by flow visualization and numerical simulation by the vortex method. The vortex method. especially the vortex stick method, is employed to investigate the vortex structure in the wake of the two wings. The pressure is estimated by the Bernoulli equation, and the lift on the wing are also obtained. As the results the eddies near the leading edge of each wing in the fling stage take a convex shape because the eddies shed from both tips entrain the flows and the downwash in the rotating stage is deflected toward the outside because the outside tip vortex is stronger than the inside one. And the lift coefficient on the wings in this mechanism is almost independent of the Reynolds number.

• Journal of the Korean Applied Science and Technology
• /
• v.29 no.1
• /
• pp.33-39
• /
• 2012

A numerical simulation of plume from a stack into atmospheric cross flow is investigated using a two-dimension model. The simulation is based on the ${\kappa}{\sim}{\varepsilon}$ turbulence model and a finite volume method. In this paper, it mostly researches how the wind velocity affects the flue gas diffusion from an 80 m high stack. Wind velocity is one of the most important factors for flue gas diffusion. The plume shape size, the injection height, the NO pollutant distribution and the concentration at the near ground are presented with two kinds of wind velocities, 1 m/s and 5 m/s. It is found that large wind velocity is better for flue gas diffusion, it generates less downwash. Although the rise height is lower, the pollutant dilutes faster and more sufficient.

• Journal of Korean Society for Atmospheric Environment
• /
• v.11 no.2
• /
• pp.145-152
• /
• 1995

Predictability of a Gaussian model, ISCST2 was assessed by scaling up wind tunnel experiments with a 1/3,000 terrain model to the real scale. Concentration profiles obtained from the flat-terrain experiment in the neutral condition were estimated to be in agreement with the calculated ones from ISCST2 in the stability class A, but the difference between the two was still large. Concentration profiles from the mountainous-terrain experiments were better fitted to the calculated ones primarily because in the experiment, concentration behind the source was raised due to the effect of a hill in the upstream side. Model prediction was improved with including the downwash effect of buildings and the hill, but overall concentration profiles were not much different from a typical Gaussian profile. While concentration profiles in the experiments were changed with local flows by varying the wind direction and the topography, those from the Gaussian modeling were mot freely changed together with these variations.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.12 no.9
• /
• pp.843-852
• /
• 2000

The flow characteristics and the heat transfer rate on a surface by interaction of a pair of vortices were studied experimentally. The test facility consisted of a boundary-layer wind tunnel with a vortex introduced into the flow by half-delta winglet protruding from the surface. In order to control the strength of the longitudinal vortices, the angles of attack of the vortex generators were varied from $\pm20\;degree\;to\;\pm45$ degree, but spacings between the vortex generators were fixed to 4 cm. The 3-dimensional mean velocity measurements were made using a five-hole pressure probe. Heat transfer measurements were made using the thermochromatic liquid to provide the local distribution of the heat transfer coefficient. By using the method mentioned above, the following conclusions were obtained from the present experiment. The boundary layer was thinned in the regions where the secondary flow was directed toward the wall and thickened where it was directed away from the wall. The peak augmentation of the local heat transfer coefficient occurred in the downwash region near the point of minimum boundary-layer thickness.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.27 no.1
• /
• pp.105-116
• /
• 2003

The flow structure around the free end of a finite circular cylinder (FC) embedded in an atmospheric boundary layer (ABL) over open terrain was investigated experimentally with varying the free end shape. The experiments were carried out in a closed-return type subsonic wind tunnel. A finite cylinder with an aspect ratio (L/D) of 6 was mounted vertically on a long flat plate. The Reynolds number based on the cylinder diameter is about Re=7,500. The velocity fields near the FC free end were measured using the single-frame double-exposure PIV method. As a result, for the FC with a right-angled free end, there is a peculiar vortical structure, showing counter-rotating twin vortices near the FC free end. It is caused by the interaction between the entrained irrotational fluids from both sides of FC and the downwash flow from the FC free-end.

• Journal of the Korean Society for Aviation and Aeronautics
• /
• v.3 no.1
• /
• pp.81-95
• /
• 1995

공기의 흐름 중에 있는 유한 날개의 끝에서는 날개끝 와류로 인하여 날개에 내리흐름(downwash)이 발생하게 된다. 이러한 내리흐름은 유도항력을 발생시켜 양항특성이 감소하게 된다. 따라서 날개끝 와류를 적절히 제어하면 어느 정도 유도항력을 감소시킬 수 있다. 본 논문에서는 직사각형 날개와 테이퍼형 날개 끝에 여러 가지 형상의 strake를 장착하거나, 날개끝 와류를 제어하기 위하여 여러 개의 slot을 형성시켰을 때의 양항특성을 실험 및 수치해석으로 연구한 결과를 기술하였다. 실험결과 직사각형 날개끝에 장착한 wing tip strake의 밑변을 바깥쪽으로 절단한 wing tip strake의 양항특성이 받음각 $8^{\circ}$ 이상에서 우수하였고, 반면에 밑변을 절단하지 않은 경우는 받음각 $0^{\circ}\;^{\sim}\;8^{\circ}$ 사이에서 기본날개보다 양항비가 증가하였다. 테이퍼형 날개끝에 wing tip strake를 장착하였을 때의 양항비는 받음각 전 범위에 걸쳐 기본날개보다 증가하였으며, 받음각$8^{\circ}$ 이상에서 wing tip strake의 밑변을 절단하지 않은 wing tip strake의 양항특성이 우수하였다. 방사형 다중슬롯의 경우 날개끝의 앞전보다 뒷전 쪽에 형성시키는 것이 양항비특성이 우수하였다.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.40 no.8
• /
• pp.495-501
• /
• 2016

The measurement of icing conditions needs to be carried out accurately by the ice detector system of an aircraft. Ice detector systems should be installed in locations not affected by backwash, rotor downwash or moving doors or other equipment. Various analyses were carried out in order to find the proper locations sufficiently far from these interfering effects. In this study, the optimum position of the ice detector was assessed using computer simulation, with respect to different flight modes, flow velocities and the amount and distribution of liquid water around the sensor.