에코 데크 플레이트 시스템은 철선일체형 거더와 아연도금 강판을 볼트에 의해 일체화시키기 때문에 기존에 용접에 의해 제작된 철선일체형 데크 플레이트에 비해 친환경 및 우수한 공법으로 인정받고 있다. 본 연구에서는 에코 데크 플레이트의 구조적 거동을 평가하기 위해 12가지 형태의 시험체를 동일한 조건으로 2개씩 총 24개의 시험체를 실물크기로 제작하여 실험적 연구를 수행한다. 실험결과 시공하중 작용에 대한 허용 처짐은 설계값 이내의 값을 나타내 만족하는 것으로 나타났으며, 래티스 철선의 가공은 아래로 향하게 절단해 제작하는 것이 구조적으로 유리한 것으로 나타났다. 또한, 하부철선으로 D13을 사용한 시험체의 경우에는 하부철선과 래티스 철선의 용접부위에서 파괴가 발생해 공장 제작 시 용접에 대한 개선안의 마련이 필요하다.
This study was to perform the kinetic analysis of forward $1\frac{1}{2}$ somersault on the platform diving. Six men's diving players of the Korea national reserve athletes participated in this study. The variables were analyzed response time, velocity, center of mass (COM), angle, center of pressure (COP) and ground reaction force (GRF) of motion. For measure and analysis of this study, used to synchronized to 4 camcorder and 1 force plate, used to the Kwon3D XP (Ver. 4.0, Visol, Korea) and Kwon GRF (Ver. 2.0, Visol, Korea) for analyzed of variables. The results were as follows; Time factor were observed in maximum knee flexion depending on the extent of use at phase 1 of take-off to execute the somersault. This enabled the subject to secure the highest possible body position in space at the moment of jumping to execute the somersault and prepare for the entry into the water with more ease. Regarding the displacement of COM, all subjects showed rightward movement in the lateral displacement during technical execution. Changes in forward and downward movements were observed in the horizontal and vertical displacements, respectively. In terms of angular shift, the shoulder joint angle tended to decrease on average, and the elbow joints showed gradually increasing angles. This finding can be explained by the shift of the coordinate points of body segments around the rotational axis in order to execute the half-bending movement that can be implemented by pulling the lower limb segments toward the trunk using the upper limb segments. The hip joint angles gradually decreased; this accelerated the rotational movement by narrowing the distance to the trunk. Movement-specific shifts in the COP occurred in the front of and vertical directions. Regarding the changes in GRF, which is influenced by the strong compressive load exerted by the supporting feet, efficient aerial movements were executed through a vertical jump, with no energy lost to the lateral GRF.
The pressure reducing valve for water is controlled by the load of the compression spring and the force of the fluid acting on the diaphragm of the stem. Repeated upward and downward reciprocation of the pressure-reducing valve stem damages the diaphragm, resulting in leakage. In this study, we designed a stem without a diaphragm and adjusted the stiffness of the compressing spring. In order to select the spring stiffness, springs offering a stiffness of -20%, -10%, 0%, and 10% with respect to the stiffness of the compression spring attached to the existing pressure reducing valve stiffness. A prototype for the pressure reducing valve was fabricated and the pressure change was evaluated for the target static pressure (6 bar) by testing the pressure characteristics after mounting the modified stem and each compression spring. Evaluation of the pressure characteristics was carried out using ASSE 1003 and KS B 6153. In addition, the flow rates were compared by internal flow analysis of the conventional pressure reducing valve and the pressure reducing valve using the modified stems, and the flow analysis was performed using Solidworks flow simulation 2018. The spring stiffness was constantly discharged at the target static pressure of 3.793 kgf/mm, and the flow rate was increased by about 15% compared with the conventional pressure reducing valve.
Pile foundation is a typical form of bridge foundation and viaduct, and large-diameter rock-socketed piles are typically adopted in bridges with long span or high piers. To investigate the effect of a mountain slope with a deep overburden layer on the bearing characteristics of large-diameter rock-socketed piles, four centrifuge model tests of single piles on different slopes (0°, 15°, 30° and 45°) were carried out to investigate the effect of slope on the bearing characteristics of piles. In addition, three pile group tests with different slope (0°, 30° and 45°) were also performed to explore the effect of slope on the bearing characteristics of the pile group. The results of the single pile tests indicate that the slope with a deep overburden layer not only accelerates the drag force of the pile with the increasing slope, but also causes the bending moment to move down owing to the increase in the unsymmetrical pressure around the pile. As the slope increases from 0° to 45°, the drag force of the pile is significantly enlarged and the axial force of the pile reduces to beyond 12%. The position of the maximum bending moment of the pile shifts downward, while the magnitude becomes larger. Meanwhile, the slope results in the reduction in the shaft resistance of the pile, and the maximum value at the front side of the pile is 3.98% less than at its rear side at a 45° slope. The load-sharing ratio of the tip resistance of the pile is increased from 5.49% to 12.02%. The results of the pile group tests show that the increase in the slope enhances the uneven distribution of the pile top reaction and yields a larger bending moment and different settlements on the pile cap, which might cause safety issues to bridge structures.
The aim of this study was to investigate the effectiveness of self-stretching exercises for iliotibial band (ITB) (Side-lying; right hip and knee were flexed to support the pelvis while left hip was extended and adducted, Standing A; side-bending of the trunk on standing with crossed leg, Standing B; same as Standing A, except the hands were clasped overhead and shifted right side, and Standing C; same as Standing B, except moving the arms diagonally downward) to help determine the most effective self-stretching method to stretch ITB. Twenty-one healthy subjects who do not have ITB shortness from Yonsei University (14 men and 7 women) between the ages of 18 to 28 years voluntarily participated. Ultrasound was performed to measure the thickness of the ITB between the long axis of the ITB and the level parallel to the lateral femoral epicondyle during four self-stretching exercises. All data were found to approximate a normal distribution. We used a one-way repeated-measures analysis of variance (ANOVA) to compare the thickness of the ITB among all self-stretching exercises. The level of significance was set at ${\alpha}$=.05. The ANOVA was followed by Bonferroni's correction. The overall mean of ITB thickness was $1.14{\pm}.4$ mm (${\pm}$ standard deviation) in resting status. The change in the ITB thickness in percentages between the tested position of each self-stretching exercises and resting status was significant (p<.05) (Side-lying $26.62{\pm}10.18%$ with 95% confidence interval [CI]=21.99~31.25%; Standing A $29.46{\pm}16.19%$ with 95% CI=22.09~36.84%; Standing B $44.06{\pm}14.82%$ with 95% CI=37.31~50.81%; Standing C $53.76{\pm}12.1%$ with 95% CI=48.25~59.29%). Results indicated significant differences among four self-stretching exercises except Side-lying versus Standing A (p<.01). Based on these findings, the Standing C self-stretching exercise was the most effective in stretching the ITB thickness among four types of ITB self-stretching exercises. Additionally, the Side-lying self-stretching exercise using gravity to stretch the ITB is recommended as a low-load (low-intensity), long-duration stretch.
Restorative procedures can lead to tooth fracture due to the relatively small amount of the remaining tooth structure. It is essential to prevent fractures by having a clear concept of the designs for cavity preparations. Among the several parameters in cavity designs, profound understanding of isthmus width factor would facilitate selection of the appropriate cavity preparation for a specific clinical situation. In this study, MO amalgam cavity were prepared on maxillary first premolar and filled with amalgam. Three dimensional, model with 1365 8-node brick elements was made by serial photographic method. In this model, isthmus was varied in width at 1/4, 1/3, 1/2 and 2/3 of intercuspal width and material properties were given for three element groups, i.e., enamel, dentin and amalgam. A load of 500 N was applied vertically on amalgam and enamel. In case of enamel loading, 2 model (with and without amalgam) was compared to consider the possibility of play at the interface between tooth material and amalgam. These models were analyzed with three dimensional finite element method. The results were as follows: 1. The stress was concentrated on the facio-pulpal line angle and distal marginal ridge of the cavity. 2. With the increase of the isthmus width, the stress spread around the facio-pulpal line angle and the area of stress concentration moved toward the proximal box. 3. In case of narrow isthmus width, the initiation point of crack would be in the area of isthmus corner of the cavity, and with the increase of the isthmus width, it would move toward the proximal box and at the same time the possibility of crack increase at the distal marginal ridge. 4. The direction of crack progressed outward and downward from the facio-pulpal line angle, and with the increase of the isthmus width, it approximated vertical direction. At the marginal ridge, it occurred in vertical direction. 5. It would be favorable to make the isthmus width narrower than a third of the intercuspal width, and to cover the cusp if isthmus width were wider than half of the intercuspal width. 6. It is necessary to apply the possibility of play to the finite element analysis.
사양토, 양토, 식양토의 3 가지의 토양을 $2^{{\prime}{\prime}}{\times}30cm(D{\times}L)$ column에 충진한 후 인공 산성비(pH 2.0, 4.0, 6.0) 1,200mm를 처리하여 산성비의 토양내 침투수량에 따른 토양의 산성화 경향, 토양 중 무기양분의 용탈과 이동양상과 산성비 토양투입에 따른 석회 중화양을 비교검토한 결과, 산성비 처리에 따른 각 토양의 pH 변화는 산성비의 pH가 4.0과 6.0에서는 별 차이가 없었으나, pH 2.0에서는 토심별로 큰 차이를 보였으며 pH감소는 사양토>양토>식양토의 순이었고, 치환산도(치환성 Al+H)는 식양토>양토>사양토의 순위였다. 산성비에 따른 각 토양의 토심별 양분 용탈량은 산성비의 pH 2.0에서 많았으며, 사양토, 양토와 식양토의 경우, 각토양 공히 Ca>K>Mg 순위였다. 토양의 pH감소와 치환산도(치환성 Al+치환성 H)는 사양토 > 양토 > 식양토의 순위였으나, pH감소에 따라 증가되는 치환산도는 그 토양의 CEC범위내 이었다. 토양내의 치환성 Al는 토양의 pH가 5이하에서는 거의 없었다. pH 3.0인 산성비(황산:질산=2:1, $1,200mm\;year^{-1}$)의 유입에 따른 H이온의 유입은 $12kg\;ha^{-1}\;year^{-1}$, 산성비의 토양유입은 S와 N가 각각 128과 $56kg\;ha^{-1}{\cdot}year^{-1}$이었으며, 이를 중화할 수 있는 소석회의 양은 $444kg\;ha^{-1}\;year^{-1}$이지만 실제로 용탈된 염기는 소석회로 사양토 923, 양토 1,731, 식양토 $1,608kg\;ha^{-1}\;year^{-1}$로 추정되었다.
본 연구에서는 3차원 유한요소 해석을 수행하여 터널굴착에 의한 말뚝의 거동변화를 지배하는 말뚝선단에 대한 터널의 상대 위치를 고려하여 분석하였다. 수치해석 결과를 순수하게 터널굴착으로 발생한(Tunnelling-induced) 말뚝두부의 침하, 상대변위, 체적손실률(Volume loss), 말뚝의 축력, 전단응력 그리고 겉보기안전율 등을 분석하였다. 터널과 말뚝선단의 상대위치를 고려했을 때 말뚝선단이 터널굴착으로 인한 지반침하 영향권 내부에 존재하는 경우 Tunnelling-induced 말뚝두부의 침하는 지표면의 침하보다 크게 나타났으며, 이는 말뚝에 Tunnelling-induced 인장력을 발생시켰다. 반대로 말뚝선단이 터널굴착으로 인한 지반침하 영향권 외부에 존재할 경우, 말뚝상부에서 유발된 하향의 전단응력으로 인해 말뚝에는 Tunnelling-induced 압축력이 작용하였다. 수치해석을 통해 분석된 하중-변위 관계를 이용하여 겉보기안전율을 분석한 결과 말뚝선단이 터널굴착으로 인한 지반침하 영향권 내부에 존재할 경우 말뚝의 겉보기안전율은 평균 약 36% 감소하는 것으로 나타났다. 터널의 상대위치에 따른 전단응력전이 매커니즘을 Tunnelling-induced 말뚝축력, 전단응력과 말뚝의 겉보기안전율을 고려하여 심도 있게 고찰하였다.
최근 개착식 터널공법으로 널리 사용되고 있는 프리캐스트 라이닝 아치 구조물에 대하여 현장 계측과 수치해석 결과를 비교하여 3힌지 프리캐스트 아치 구조물의 거동을 분석하였다. 현장 계측결과, 천단부에서 가장 큰 연직변위가 측정되었으며 초기에는 상방향으로 변위가 발생하다가 뒤채움 흙이 천단부보다 높아지면서 하방향으로 변위가 발생하였다. 천단부는 최종적으로 원 위치로부터 상방향 19 mm에서 변위가 수렴하였다. 측벽부 최대 수평변위 지점에서의 수평변위는 아치상단까지 뒤채움시 터널 내측으로 발생하여 두 지점간의 수평거리가 줄어들다가, 상부 성토가 진행될수록 수평변위는 감소하여 원래 위치로 이동하였다. 프리캐스트 아치구조물에 대한 변위 분석결과, 지반-구조물의 상호작용을 잘 관찰할 수 있었으며 따라서 기존의 강성구조물과 비교하여 경제적인 설계가 가능할 것으로 기대된다. Duncan 모델을 사용한 유한요소 해석결과를 현장 변위 계측값과 변위 형상 등과 비교하면 유사한 결과를 나타내었다. 수치해석 결과에 의한 측벽부의 수평토압계수는 터널 좌측부는 0.4, 우측부는 0.7에서 수렴하여, 편토압이 발생하는 현장상황 및 현장 변위 계측 결과와도 일치하였다.
본 연구에서는 3차원 유한요소해석을 실시하여 말뚝에 인접한 터널시공으로 인한 말뚝의 거동을 터널로부터 말뚝선단의 횡방향 이격거리를 고려하여 분석하였다. 단독말뚝 및 간격 2.5d인 $5{\times}5$ 군말뚝을 고려하였다. 여기서 d는 말뚝의 직경을 의미한다. 수치해석에서는 순수하게 터널굴착(tunnelling-induced) 으로 인해 유발된 말뚝침하, 전단응력, 상대변위, 축력분포, 겉보기안전율 및 터널굴착 영향권을 고찰하였다. 말뚝이 터널굴착으로 인한 지반침하 영향권 내부에 존재할 경우 말뚝두부의 침하는 Greenfield 조건의 지표면 침하보다 최대 대략 111% 크게 산정되었고, 군말뚝의 경우 단독말뚝과 비교하여 말뚝침하가 크고 축력이 작게 나타났는데 이는 군말뚝내의 말뚝이 인접지반과 함께 블록(block)의 형태로 거동하는 것으로 분석되었다. 또한 말뚝의 상부에서는 상향의 마찰 저항력이 발생하고 말뚝의 하부에서는 하향의 마찰 저항력이 발생하여 순수하게 터널굴착(tunnelling-induced)으로 인해 말뚝에는 인장력을 발생시켰다. 한편 말뚝이 영향권 외부에 존재할 경우 말뚝에는 tunnelling-induced 압축력이 발생하였다. 수치해석을 통해 분석된 하중-침하 관계로부터 말뚝의 겉보기안전율을 계산한 결과 터널굴착 이전에 비해 대략 45% 감소된 것으로 나타났다. 따라서 이는 말뚝의 사용성에 심각한 문제를 유발시킬 수 있는 것으로 나타났다. 본 연구를 통해 지반침하 영향권에 따른 단독말뚝 및 군말뚝의 거동을 심도 있게 고찰하였다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.