• 소성∙가공
• /
• 제27권1호
• /
• pp.54-59
• /
• 2018

In connecting parts of a hydrogen fuel cell vehicle, since the rubber ring is permeable to hydrogen, it is necessary to use a metal sealing structure which ensures leakage stability. Finite element analysis was performed to verify the fitting characteristics of the metal sealing structure, which is used to connect the pipe to a high pressure hydrogen FCEV tank. Deformation shape, contact distance and axial load were compared experimentally and these values were in agreement with each other. In the contact surface, between the pipe and the fitting body, the stress at the edge of the contact surface was higher than the center point, which was considered to be a good characteristic in view point of the leakage. The location of the contact points has almost no change in the upper part of the fitting, but that of the lower parts move downward as the fastening amount increases. The contact pressure at the lower part is maintained at the same constant level.

• 대한치과보철학회지
• /
• 제33권1호
• /
• pp.32-47
• /
• 1995

The purpose of this study was to determine the displacement of prosthesis & abutment and the stress distribution patterns induced in the periodontium by applying force to the fixed prosthesis. Two levels of periodontal support were compared using two-dimensional finite element stress analysis after placement of 3unit or 4 unit fixed partial denture(FPD) in case of missing of the lower first molar. Concentrated vertical load was delivered at the cusp tip of the second bicuspid or the central fossa of the pontic. The following results were obtained : 1. The greater the loss of alveolar bone in abutment teeth area, the greater the displacement of FPD and the stress concentration in alveolar bone around abutment. 2. The amount and direction of displacement and distribution of stress in the 4-unit FPD was better than those in the 3-unit FPD. 3. Multiple abutments reduced the amount of mesial and downward displacement of the weaked abutments and more uniformly distributed the stresses.

• 대한치과보철학회지
• /
• 제35권2호
• /
• pp.308-329
• /
• 1997

A lot of the research paper was reported about the result of influence of IMC (Intra-mobile connector) in the IMZ implant placed solely in the alveolar bone, but reports about the effect of IMC on functional load at state of connecting with natural teeth ere rare. The major propose of this study was find the mechanical character of IMC itself by using the finite element analysis program after simulated variance of condition connected with the natural teeth and implant on funcional load. When first and second premolar was lost, IMZ implant was placed with a diameter of 3.3mm and a length of 13mm with IMC in second premolar area. Rigid connection was done and the non-figid connention was located on the female part of the canine abutment and the implant respectively and then both the infraocclusion of $30{\mu}m$ and the non-infraocclusion under the load of 40kg applied to the portion of the natural teeth, the pontic and the implant. The displacement and the stress of it was estimated and analyzed IMC itself of the rigid connection and the non-rigid connection was grouped. The following result were obtained. 1. In all groups, the displacement of Y-axis was greater than that of X-axis and the aspect of displacement showed that IMC was displaced downward and to the center. 2. There was no differences in the displacement of IMC regardless of the connection type. 3. In the displacement of IMC, I 4 was the least, I 1 and I 3 are similar and I 2 was the greatest. 4. There was no differences in the peak value of maximal stress of IMC regardless of the connection type. 5. In the peak value of maximal stress of IMC, I 4 was the least, I 1 and I 3 were similar, and I 2 was the largest.

• 한국구조물진단유지관리공학회 논문집
• /
• 제21권6호
• /
• pp.44-51
• /
• 2017

최근 국내 자동차 보유대수의 급격한 증가로 도심지 주차문제가 복잡해지고 있다. 도심지 주차문제 해결에 있어 공작물 주차장이 주목을 받고 있다. 그러나 공작물 주차장은 전체 높이 8 m 이하로 건설되도록 규정되어 있다. 이에 본 연구에서는 층고절감 및 장스팬화가 가능한 와이드 합성보를 개발하여 휨성능을 평가하였다. 휨 성능 실험 결과, 강재보의 두께가 3 mm 증가($6mm{\rightarrow}9mm$)함에 따라 휨강도는 약 20%가 증가하였다. 보 보강철근(트러스철근)의 형태(삼각형, 사각형)은 휨강도에 영향을 미치지 않았다. 보 보강철근(트러스철근)이 없는 경우는 있는 경우보다 약 10%가량 휨강도가 저하되었다. 또한 하중이 증가할수록 중립축은 상부로 이동하지만 일정하중을 넘어가면 중립축이 다시 하부로 이동하는 결과를 나타내었다.

• 한국지반신소재학회논문집
• /
• 제19권1호
• /
• pp.83-91
• /
• 2020

본 연구에서는 대형 구조물 기초 및 교량 하부기초로 사용이 증가되고 있는 현장타설말뚝 및 대형 Caisson 기초의 지반조건 변화에 따른 지지거동 특성에 대하여 분석하였다. 현장타설말뚝의 항복하중 분석법을 이용하여 산정한 허용지지력은 각 방법마다 서로 유사한 허용지지력을 산정하는 것으로 분석되었다. 또한 극한하중 분석법으로 산정한 허용지지력은 각 방법에 따라 지지력의 차이가 큰 것으로 분석되었고, 기존의 유사 사례현장을 분석하여 재하하중과 침하량에 관한 관계를 제시하였으며, 이를 통하여 향후 설계 및 시공시 말뚝의 침하특성을 평가하기 위한 경험식으로 유용하게 활용 가능할 것으로 판단된다. 또한 대형케이슨의 침설시 발생하는 지반반력 분포에 대해 검토한 결과 풍화암층 구간은 기초 모서리부에서 항복이 발생된 후 지반반력이 감소하여 거의 일정한 지반반력 분포를 나타내었으며, 기반암층 구간에서는 중앙부의 지반반력 증가로 인해 기초 중앙부가 아래로 볼록한 형태의 지반반력 형태로 변형되었다. 이와 같은 결과를 이용하여 Fang(1991) 및 Kőgler(1936)가 기존에 제시한 이론을 증명하였다.

• 한국산학기술학회논문지
• /
• 제17권12호
• /
• pp.686-691
• /
• 2016

용접강구조물에서는 용접비드와 같은 응력집중부가 많이 존재한다. 또한 용접부에서는 용접결함이 발생할 가능성이 많다. 반복적인 피로하중이 응력집중부에 작용하면 응력집중부에서 피로균열이 발생하고, 발생된 균열의 전파에 의해 피로파괴사고를 일으킨다. 따라서 피로파괴사고를 미연에 방지하기 위하여 균열발생수명과 균열전파수명과 같은 피로수명의 파악이 필요하다. 본 연구에서는 피로균열전파특성 연구에 사용되는 컴플라이언스를 도출하였다. 이 컴플라이언스는 피로균열의 자동화 측정에 활용할 수 있다. 본 연구에서는 CT시험편에 대하여 in-house FEM program을 사용하여 컴플라이언스를 계산하였다. 이 계산결과는 저자의 앞선 연구에서 본 프로그램을 사용하여 계산한 J integral의 계산결과와 대비하여 a/W와의 관계를 제시하였다. 그리고 또한 CT시험편 Back Face의 중앙부로부터 위아래 방향의 스트레인 분포에 계산을 실시하였다. 이 분포에서는 중심으로부터 위아래로 갈수록 스트레인이 감소하는 경향을 나타내었다. 이상의 계산과정으로부터 균열진전시험의 자동수행을 위한 컴플라이언스를 얻을 수 있었다. 이것으로부터 CT 시험편의 피로균열진전시험의 자동화에 활용이 가능하게 되었다.

• 한국건설관리학회:학술대회논문집
• /
• 한국건설관리학회 2004년도 제5회 정기학술발표대회 논문집
• /
• pp.472-475
• /
• 2004

기존의 양중부하의 계산은 단순히 자재묶기 $\cdot$ 상승 $\cdot$ 설치 $\cdot$ 하강의 4단계로 산정한다. 이는 타워크레인의 양중작업과 관련되는 다른 영향요인을 고려하지 못한다는 단점을 내포하고 있다. 이에 본 연구에서는 기존 타워크레인의 양중작업에서 시간을 예측하는데 고려하지 못하였던 많은 요인을 도출하고자 하였으며 이를 통해 타워크레인의 양중작업시 요구되는 양중시간에 대한 예측모델을 구축하였다. 타워크레인의 양중시간을 정확히 예측하기 위해서 양중시간에 영향을 미치는 변수를 자재관련, 타워크레인의 특성, 양중작업관련 타워크레인 운용 및 기상상황과 관련하여 28개의 다양한 변수들을 식별하였다. 이를 통해 타워크레인의 양중작업 시 요구되는 양중시간에 대한 예측모델을 구축하였다. 타워크레인의 양중시간 예측을 정확히 산정하기 위해 예측모델을 상차양중모델과 하차양중모델로 구분하였고 양중에 미치는 영향요인을 양중대상에 따라 선별하여 다중회귀분석의 과정을 거쳐 그 신뢰도를 높이도록 하였다.

• 한국환경과학회지
• /
• 제4권5호
• /
• pp.103-103
• /
• 1995

In the Chinhae Bay, Korea, sedimentation rates and sedimentary record of anthropogenic metal loads were determined by $^{210}Pb$ dating and heavy metal analysis of four sediment cores . The sedimentation rates varied from 0.16g/$cm^2$/yr(3.1mm/yr) at Sta. Ct, located within narrow waterway to 0.24g/$cm^2$/yr(4.8mm/yr) at Sta. Cl, located in Haengam Bay. Maximum contents of Mn, Zn, Cu and Cr were observed at Sta. C2 located near the mouth of Masan Bay, while minimum contents were observed at Sta. CB. Mn/Fe ratios at Sta. C2 and Sta. C4 showed gradually increasing and decreasing downward, respectively, in the upper layer of sediment cores. This suggests that Mn may be diagenetically redistributed in highly reduced environment. At Sta. C2, the concentrations of Zn and Cu began to increase from 1920s by anthropogenic input and have been remarkablely increasing since mid 1960s. At Sta. C3, located near Sungpo, anthropogenic input of these two elements has also slightly increased after 1970s. However, pollution of these two elements was not significant in Haengam Bay(Sta. Cl) and Chiljun watenway(Sta. C4). The pollution of Co, Ni and Cr was not remarkable in all core samples except surface sediment of Sta. C2. The total input of anthropogenic Zn and Cu since 1920s was estimated to be 28∼792 ㎍/cm2 and 0∼168㎍/cm2, respectively. Sta. C2 showed remarkablely higher values relative to other stations: anthropogenic loads of Zn and Cu constituted 27% and 29% of the total sedimentary inventories at the present day, respectively. Fe, Ni, Cr and Co contents showed good correlation(r>0.8) with each other. Anthropogenic Zn and Cu also showed a very good positive correlation(>0.9). However, correlation between these two group of element was quite scattered, indicating different sources and geochemical behaviors.

• 한국환경과학회지
• /
• 제4권5호
• /
• pp.489-500
• /
• 1995

In the Chinhae Bay, Korea, sedimentation rates and sedimentary record of anthropogenic metal loads were determined by $^{210}Pb$ dating and heavy metal analysis of four sediment cores . The sedimentation rates varied from 0.16g/$cm^2$/yr(3.1mm/yr) at Sta. Ct, located within narrow waterway to 0.24g/$cm^2$/yr(4.8mm/yr) at Sta. Cl, located in Haengam Bay. Maximum contents of Mn, Zn, Cu and Cr were observed at Sta. C2 located near the mouth of Masan Bay, while minimum contents were observed at Sta. CB. Mn/Fe ratios at Sta. C2 and Sta. C4 showed gradually increasing and decreasing downward, respectively, in the upper layer of sediment cores. This suggests that Mn may be diagenetically redistributed in highly reduced environment. At Sta. C2, the concentrations of Zn and Cu began to increase from 1920s by anthropogenic input and have been remarkablely increasing since mid 1960s. At Sta. C3, located near Sungpo, anthropogenic input of these two elements has also slightly increased after 1970s. However, pollution of these two elements was not significant in Haengam Bay(Sta. Cl) and Chiljun watenway(Sta. C4). The pollution of Co, Ni and Cr was not remarkable in all core samples except surface sediment of Sta. C2. The total input of anthropogenic Zn and Cu since 1920s was estimated to be 28~792 $\mu\textrm{g}$/cm2 and 0~168$\mu\textrm{g}$/cm2, respectively. Sta. C2 showed remarkablely higher values relative to other stations: anthropogenic loads of Zn and Cu constituted 27% and 29% of the total sedimentary inventories at the present day, respectively. Fe, Ni, Cr and Co contents showed good correlation(r>0.8) with each other. Anthropogenic Zn and Cu also showed a very good positive correlation(>0.9). However, correlation between these two group of element was quite scattered, indicating different sources and geochemical behaviors.

• 대한치과보철학회지
• /
• 제36권2호
• /
• pp.293-301
• /
• 1998

The purpose of this study was to investigate the effects of load on root that was applied to edentulous area in three simulated situation, in each case the guiding planes of abutment were right vertical, 95 degrees, or 100 degrees to residual ridge. The 2-dimensional finite element method was used and the finite element model was prepared as fellows. Right mandibular 1st and 2nd molar was lost and the 2nd premolar with distal rest was used as primary abutment which had three different degrees of guiding plane. Then 150N of compressive force was applied to central fossae of the 1st and 2nd molars and von Mises stress and displacement was measured. The results were as follows; 1. Irrespective of slopes of guiding planes, the stress was concentrated on mesial side of root apex and distal side of coronal portion of root, in particular on junction with distal alveolar bone. As slopes of guiding planes were increased. stress on root and compact bone surrounding abutment was increased but no considerable effect was seen on compact bone of residual ridge. 2. Distal side of coronal portion of root limited by periodontal ligament was displaced distally and mesial side of apical portion was mesially. With slope of guiding plane increasing, the pattern of displacement was similar with one another but the quantity was increased. 3. Both abutment & alveolar bone were displaced downward and root of abutment, especially distal side of coronal portion, was displaced severely. As the guiding plane was tiffed more mesially over $90^{\circ}$, the degree of displacement was also increased.