• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2000.11a
• /
• pp.793-797
• /
• 2000

The environmental problems by using coolant demanded the new cooling methods. As one of them the studies on the dry grinding with compressed cold air have been done. The cooling method using compressed cold air was effdve thmugh going down the temperature of compressed air supplied below $-25^{\circ}C$ and inneasing the amount of mmpresd cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using MQL(Minimum Quantity Lubrication) or mist newly were suggested. These two methods can satisfy both cooling effect and lubrication with only small amount of coolant, also has the benefit in the point of decreasing the envimnmental pollution. This paper focused on analyzing the grindmg characteristics of the cooling method using mid. The generated heat and grinding force of the cooling method using mist were compared with them of coolant and compressed cold air. And them grinding test according to the temperature of compressed cold air, mist spray amount and mist supply direction were done.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2006.05a
• /
• pp.555-556
• /
• 2006

In recent years, the higher flatness level in wafer shape has been strictly demanded with a high integration of the semiconductor devices. It has become difficult for a conventional wafer preparing process to satisfy those demands. In order to meet those demands, surface grinding with in-feed grinder is adopted. In an in-feed grinding method, a chuck table fur fixing a semiconductor wafrr rotates on its rotation axis with a slight tilt angle to the rotation axis of a cup shaped grinding wheel and the grinding wheel in rotation moves down to grind the wafer. So, stability of the grinder structure is very important to aquire a wafer of good quality. This paper describes the features of the in-feed grinder and some FEM analysis results of the grinder structure.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.05a
• /
• pp.24-27
• /
• 2002

The environmental problems by using coolant demanded the new cooling methods. As one of them, the studies on the finding with compressed cold air and oil mist have been done. The cooling method using compressed cold air was effective through going down the temperature of compressed air supplied below $-25^{\circ}$ and increasing the amount of compressed cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using oil mist newly were suggested. This method can satisfy both cooling effect and lubrication with only small amount of coolant, also have the benefit in the point of decreasing the environmental pollution. This paper focused on analyzing the grinding characteristics of the cooling method using oil mist. The grinding test according to compressed cold air, oil mist spray pressure and oil mist supply direction were done.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2002.10a
• /
• pp.254-257
• /
• 2002

As the large Coolant amount used of a machine holds mass serious trouble recently, an environment pollution is increased, and a machine is conquering large specific gravity in an empty cost plane. It is the stage that must reexamine the parts washing that processing is later with this current way or a problem of a liquid waste treatment back. The environmental problems by using coolant demanded the new cooling methods. As one of them, the studies on the grinding with compressed cold air and oil mist have been done. The cooling method using compressed cold air was effective through going down the temperature of compressed air supplied below -$25^{\circ}C$ and increasing the amount of compressed cold air, but had not enough cooling effect due to the low performance of lubrication. Therefore, the cooling methods using oil mist newly were suggested. This method can satisfy both cooling effect and lubrication with only small amount of coolant, also have the benefit in the point of decreasing the environmental pollution. This paper focused on analyzing the grinding characteristics of the cooling method using oil mist. The grinding test according to compressed cold air and oil mist supply direction were done.

• Journal of the Korean Society for Precision Engineering
• /
• v.7 no.4
• /
• pp.23-28
• /
• 1990

This study is to investigate the magnitude, direction and distribution of residual stresses in surface ground plate according to working conditions. The specimens were made of structural carbon steel and were machined in various grinding conditions. These were divided in two groups; heat-treated materials and non-heat-treated materials. In each working condition, let the ground specimen generate displacements using deflection-etching techniques. At the same time, these displacements were precisely measured with electronic micrometer. Through the relation formula between the plane stress and strain, which was derived using these measured data, the values of residual stress are calculated, and the results are analyzed. These results are as follows : 1. According to the working conditions in this experiment, it can be seen that the distribution of residual stress generally had same trend and the maximum residual stress remained in 20~30 ((${\mu}m$) beneath the surface. 2. It is observed that compressive residual stress changes into tensile stress in 5~20 (${\mu}m$) beneath the surface. It is suggested that such phenomenon is originated from the friction effect in grinding process. 3. As the hardness increases by the heat treatment, residual stress increases. 4. As the fatigue strength increases by the compressive residual stress, it is desirable that the dowm feed and table feed reduce. 5. It can be seen that the more great the down feed and table feed increase, the more close the changing point, where the stress changed from compressive to tensile, is colse to the surface. This is due to the resultant effects of the grinding temperature and resistence are larger than the effect of the friction.

• Journal of Advanced Marine Engineering and Technology
• /
• v.31 no.6
• /
• pp.753-760
• /
• 2007

For protection of the cylinder wall of the ball mill for grinding raw ore. the inner side of the cylinder is covered with rubber liner. The rubber is easily worn down because the rubber relatively soft compared with raw ore. So the rubber liner in the ball mill cylinder must be replaced almost every year and the cost for replacing rubber liner formidable. In this paper, for reducing or excluding the cost of replacing rubber liner the basalt liner is designed. The basalt materials are generally harder than raw ore and the basalt liner in the ball mill does not wear down and so it can be used almost permanently. The concave surfaces are made on the liner of the ball mill and the liner in the cylinder wall plays also the role of raising the steel balls mixed in the raw ore. The section profiles of the concave surface have an important effect on the performance of the ball mill. The deep concave grooves raise the steel balls to high levels and give the large potential energy to the steel balls impacting to the raw ore. But if the concave grooves are too deep. the steel balls raised too high by the concave grooves fly along the parabolic path and reach to the other side of cylinder wall and so the steel balls do not play the roles of grinding the raw ore. The forces acting to a steel ball in a concave groove of the cylinder liner are also analyzed in this paper. The formulas calculating the height and the impact point of the steel ball are introduced and presented. Based to these formulas, the optimum section profiles of the basalt liner are presented.

• Korean Journal of Computational Design and Engineering
• /
• v.20 no.3
• /
• pp.312-319
• /
• 2015

The grinding and furbishing process as the finishing process for molds include the works such as the grinding, buffing, lapping and polishing among others. A finishing tool unit is applied to this finishing process for the burr, lapping, polishing and others of molds. A finishing tool unit can carry out the flexible machining, depending on the machining allowance for objects to be cut on the basis of the instrumental driving mechanism which enables the up, down, left and right floating, which is applied in link with the dedicated cutters and robot machining systems. This study selected the shape to increase the rotatory force of an impeller when air is discharged during the driving of a finishing tool unit, and reflected it to the impeller designing. In addition, the study analyzed each flow velocity and pressure distribution per air pressurization value and finally analyzed the rotating torque to suggest the optimal conditions in designing impellers.

• Journal of Drive and Control
• /
• v.14 no.4
• /
• pp.1-8
• /
• 2017

The Down-the-Hole hammer is one of the pneumatic drill equipment used for grinding, drilling, and mining. One the advantages of which is that a reduction work efficiency at deep site are relatively small compared to other drilling methods. Due to the large vibration in the underground area, it is difficult to measure the performance of the hammer, and hammer testing requires substantial production cost and operating expenses so research on the development of the hammer is insufficient. Therefore, this study has developed a dynamic simulation model that apprehends the operating principles of an 8-inch DTH hammer and calculates performance data such as performance impact force, piston speed, and BPM. By using the simulation model, design factors related to strike force and BPM were selected, and the influence of each design factors on performance was analyzed through ANOVA analysis. As a result, be the most important for BPM and the strike force are position of upper port that push the piston in the direction of the bit and in BPM, the size of the empty space between the bits and the piston is the second most important design factor.

• Proceedings of the Korean Printing Society Conference
• /
• 2001.06a
• /
• pp.91-91
• /
• 2001

환경문제에 대해 오래 전부터 관심을 가져온 선진국은 잉크의 수성화에 주력하여 왔으며, 그 결과 이미 수용성 소재의 양산체재에 들어가 수성 원료 사업을 대형화하는 추세에 있다. 이에 한화석유화학 중앙연구소에선 스티렌/아크릴계 수용성 High Solid 수지를 개발하여, 수성 잉크용 분산제, Resin Fortified Emulsion (RFE), UV Resist 잉크, 수성코팅제, 바닥광택제 등에 적요하기 위한 응용기술을 개발하였다. 본 연구는 수성 잉크의 주요 구성 성분인 grinding vehicle. let-down vehicle로 사용되는 수용성 High Solid 수지 (SAA 수지) 및 이를 이용한 에멀젼 수지의 합성과 수성 잉크로의 응용에 대한 것이다. SAA(HCC Soluryl Resin) 수지는 구조적으로 Styrene, Alpha-methyl Styrene, crylic Acid의 삼원공중합체이며 약 70%의 소수성 물질과 30%의 친수성 물질이 Random 하게 중합되어 있으며 약 5000∼15000정도의 낮은 분자량을 가진 물질로, 고고형분에서도 낮은 점도를 유지하기 위하여 분자량과 좁은 분자량과 좁은 분자량을 가지는 수지를 연속벌크중합방법으로 합성하였다. 또한 이를 고분자 유화제로서 사용하여 수지보강 에멀젼수지 (RFE 수지, HCC Soluryl Emulsion) 를 제조하는데 사용하였으며, SAA수지 및 RFE수지를 수성잉크용 분산제, 잉크 바인더용으로 적용하였다.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.2 no.2
• /
• pp.31-36
• /
• 2003

Base and saddle feed drive system in machine tool puts in operation for Improvement of life and endure by high frequency heat treatment. In this time, work requirement of establishment to gets by repeat experimentation. In this paper, using the finite elementary method, we predict and revision processing, and gets minimizing of deformation and reduce the progress of Grinding works. Moreover, having high frequency heat treatment, the maximum deformation genesis m the middle parts without slideway length. Take deformation Into finite element program (ANSYS) of taper process in roughing process, after having high frequency heat treatment, existed quantity of deformation can be reduced down to 80 percents.