• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 춘계학술대회 논문집
• /
• pp.799-804
• /
• 1997

This paper is concerned with the heat flux distribution and energy partition for creep-feed grinding. Form measurements of transient grinding temperatures in the workpiece sub-surface using an embeded thermocouple, the overall energy partition to the workpiece was estimated form moving heat source theory for a triangular heat flux distribution as 3.0% for down grinding and 4.5% for up grinding. The higher energy partition for up grinding can be attributed to the need to satisfy thermal compatibility at the grinding zone. The influence of cooling outside the grinding zone can be analytically taken into account by specifying convective heat transfer coefficients on the workpiecs surface h /sab a/ heat source (grinding zone) and h /sab b/ behind the heat source. The smaller energy patition together with slightly lower grinding power favors down grinding over up grinding.

• 한국생산제조학회지
• /
• 제7권6호
• /
• pp.42-48
• /
• 1998

This paper is concerned with the heat flux distribution and energy partition for creep-feed grinding. From measurements of transient grinding temperatures in the workpiece sub-surface using an embedded thermocouple, the overall energy partition to the workpiece was estimated from moving heat source theory for a triangular heat flux distribution as 3.0% for down grinding and 4.5% for up grinding. The higher energy partition for up grinding can be attribute to the need to satisfy thermal compatibility at the grinding zone. The influence of cooling outside the grinding zone can be analytically taken into account by specifying convective heat transfer coefficients on the workpiece surface ha ahead of the heat source (grinding zone) and hb behind the heat source. The smaller energy partition together with slightly lower grinding power favors down grinding over up grinding.

• International Journal of Precision Engineering and Manufacturing
• /
• 제4권3호
• /
• pp.62-67
• /
• 2003

The grinding force generated during the grinding process causes an elastic deformation of the workpiece, grinding wheel, and machine system. Thus, the true depth of cut is always smaller than the apparent depth of cut. This is known as machining elasticity phenomenon. The machining elasticity parameter is defined as a ratio between the true depth of cut and the apparent depth of cut. It is an important factor to understand the material removal mechanism of the grinding process. To increase productivity, the value of this machining elasticity parameter must be large. Therefore, it is essential to know the characteristics of this parameter. The objective of this research is to study the effect of the major grinding conditions, such as table speed, depth of cut, on this parameter experimentally, Through this research, it is found that this parameter value is increasing when the table speed is decreasing or the depth of cut is increasing. Also, this parameter value depends on the grinding mode (up grinding, down grinding).

• 한국정밀공학회지
• /
• 제18권2호
• /
• pp.171-176
• /
• 2001

This study focuses on the energy partition and heat flux distribution in creep-feed grinding. From the measurements of transient grinding temperature in the workpiece which the thermocouple was embedded, the overall energy partition to the workpiece was estimated with moving heat source theory using the developed scalene triangle heat model. The energy partition was calculated as 3.75% in down grinding smaller than 5.3% in up grinding. Also, the scalene triangle heat model was confirmed as the most optional heat model in correspond to the experimental data. Then, the heat flux distribution was calculated from temperature responses. The heat flux is negative behind the grinding zone where fluid was applied. In this experimental result, the total heat flow to the workpiece per unit width obtained by integrating the positive heat flux was 0,7W/mm for down grinding.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 추계학술대회 논문집
• /
• pp.16-21
• /
• 2004

As a new approach to analyze grinding energy, this paper introduces a specific grinding energy model based on the average grain. Using this model, grinding characteristics such as radial and tangential forces, specific grinding energy of SM45C were investigated altering grinding variables such as workpiece velocity(v) and apparent depth of cut(Z) in down-surface grinding. From the experimental results, there is no significant difference between the radial, tangential forces and vertical. horizontal forces because of small contact angle between wheel and workpiece. The specific grinding energy decreases as the maximum undeformed chip thickness increases. But, there is much difference between the specific grinding energies of the existing and the proposed model.

• 한국공작기계학회논문집
• /
• 제14권4호
• /
• pp.61-68
• /
• 2005

As a new approach to analyze grinding energy, this paper introduces a specific grinding energy model based on the average grain. Using this model, grinding characteristics such as radial and tangential forces, specific grinding energy of SM45C were investigated with changing grinding variables such as workpiece velocity(v) and apparent depth of cut(Z) in down-surface grinding. From the experimental results, the specific grinding energy decreases as the maximum undeformed chip thickness increases. And there is no significant difference between the specific grinding energies of the existing and the proposed model.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2005년도 춘계학술대회 논문집
• /
• pp.319-323
• /
• 2005

As a new approach to analyze grinding energy, this paper introduces a specific grinding energy model based on the average grain. Using this model, grinding characteristics such as specific grinding energy of SM45C were investigated with changing variables such as grain size, workpiece velocity(v) and apparent depth of cut(Z) in down-surface grinding. From the experimental results, the specific grinding energy decreases as the maximum undeformed chip thickness increases. And also the specific grinding energy increases as the grit size increases.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2005년도 추계학술대회 논문집
• /
• pp.1004-1007
• /
• 2005

As a new approach to analyze grinding energy, this paper introduces a specific grinding energy model based on the average grain. Using this model, grinding characteristics such as specific grinding energy of SM45C were investigated with changing variables such as grain size of CBN, workpiece velocity(v) and apparent depth of cut(Z) in down-surface grinding. From the experimental results, the specific grinding energy decreases as the maximum undeformed chip thickness increases.

• 한국정밀공학회지
• /
• 제15권8호
• /
• pp.26-32
• /
• 1998

The grinding force generated during the grinding process causes an elastic deformation of the workpiece, grinding wheel, and machine system. Thus, the true depth of cut is always smaller than the apparent depth of cut. This is known as machining elasticity phenomenon. The machining elasticity parameter is defined as a ratio between the true depth of cut and the apparent depth of cut. It is an important factor to understand the material removal mechanism of the grinding process. To increase productivity, the value of this machining elasticity parameter must be large. Therefore, it is essential to know the characteristics of this parameter. The objective of this research is to study the effect of the major grinding conditions, such as table speed and depth of cut, on this parameter experimentally. Through this research, it is found that this parameter value is increasing when the table speed is decreasing or the depth of cut is increasing. Also, this parameter value depends on the grinding mode (up grinding, down grinding).

• 한국정밀공학회지
• /
• 제7권4호
• /
• pp.65-72
• /
• 1990

After observing grinding characteristics according to variable grinding condition in order to raise the grinding effect without making worse the grinding quality by using general grinding machine, main conclusions of this study are as follows; 1) When grinding quality is constant, grinding effect is changed according to the speed of the workpiece. But the rapidly increasing critical speed of table is($V_w{\leq}4m/min$). 2) As grinding effect is equal, the lower the speed of the workpiece becomes, the lower the grinding force and surface roughness obtains good results. 3) In terms of grinding method, the down cut grinding method produces good grinding surface royghness in case of little grinding depth;otherwise, the up cut method in case of more grinding depth.