• Proceedings of the IEEK Conference
• /
• 2002.06d
• /
• pp.81-84
• /
• 2002

This paper presents the real-time PCB(Printed circuit board) inspection system that can detect thin open/short error using the line scan camera. After a overall introduction of our system, the outline of our inspection methods are described. The goal of our inspection system is the real time and detailed inspection using the line scan camera. To perform inspection processing in real-time, we utilize double buffering structure. In order to solve the problem of unexpectable pixels of PCB, we propose melting process which eliminates unexpectable pixels of PCB. The design and development of our prototype of PCB ins- pection system is discussed and test results are presented to show the effectiveness of the developed inspection algorithm.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.13 no.6
• /
• pp.1172-1179
• /
• 2010

Since HEMP has the very short rising time and propagates widespreadly with several tens of kV/m, it threatens most of systems in its cover range. Therefore, it is important to research coupling mechanism into systems and establish countermeasures for the HEMP to protect systems effectively. This paper analyzed characteristics and trends of currents to be induced at the load of a line which is located over ground with different conditions such as polarization, incidence angle, line length and height etc. We applied double exponential waveform as the HEMP shape and used BLT method to analyze the coupling route into the line. Also, we compared the simulation data of chain matrix modeling to verify reliability of BLT modeling. In the result, two data is almost agreed.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.19 no.5
• /
• pp.912-919
• /
• 1994

A new error control line code based on an extended Hamming code is proposed and its performance is analyzed in this paper. The proposed code is capable of single error correction and double error detection since its minimum Hamming distance is 4. In addition, the error detection capability can be oncreased due to the redundancy bit used for line coding. As a result, the proposed code shows lower code rate, but better spectral characteristics in low frequency region and lower residual bit error rate than the conventional error correction line code using Hamming (7, 4) code.

• Journal of international Conference on Electrical Machines and Systems
• /
• v.2 no.2
• /
• pp.246-253
• /
• 2013

The Modular Multilevel Converter (MMC) with full bridge cells is available for utility interactive inverter in high voltage line. When it is interconnected with power line, it is possible to control the active power flow in order to supply or charge the power in the line. This research applied the MMC to grid connection system of distributed generator and a power flow control for the MMC is investigated. Theory of power flow between the MMC and the power line is described and control method of power flow and capacitor voltages on arm cells for the MMC are proposed. And effectiveness of the proposed control method is presented by simulation.

• Proceedings of the KIEE Conference
• /
• 2007.07a
• /
• pp.913-914
• /
• 2007

Power transformer shall be designed and constructed to withstand the mechanical and thermal stresses produced by external short circuits which include three-phase, single line to ground, double line-to-ground, and line-to-line faults on any one set terminals at a time. This paper presents the method of short-circuit test and means of evaluation during and after each test to judge the results of short-circuit tests.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2005.11a
• /
• pp.955-958
• /
• 2005

In this study, the wind load characteristics for a transmission tower is investigated considering the effect of the transmission lines through stochastic analysis. The assemblage of the transmission line and insulator are modeled as a double pendulum system connected to the SDOF model of the tower It is observed that the background component of the overturing moment induced by the wind response of the transmission line has considerable portion in the total overturning moment. Based on this result, a rotational viscoelastic damper (VED) is proposed for the mitigation of the transmission line reactions, which act as wind load transferred to the tower. To verify the effectiveness of the proposed strategy, time history analysis is conducted for different wind velocities and VED damping constants. From the analysis, the proposed VED is proved to be effective for mitigation of the background component rather than the resonance component of the transmission line reaction.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.27 no.3
• /
• pp.383-387
• /
• 2000

Fusion is defined as union of two separate tooth buds at some stage in their development with confluence of dentin and characterized by separate root canal and large single crown, while gemination is defined as an attempt of the single tooth bud to incompletely divide and usually result in a single root with one root canal and two completely or incompletely separated crowns. It is sometimes difficult to decide whether an abnormally large tooth is the result of fusion of a normal and a supernumerary tooth, or of gemination; use of the term 'Double tooth' may make the clinicians avoid this difficulty(Brook & Winter). Commonly there are no symptoms, but the problems associated with these anomalies include esthetics, possible loss of arch length and delayed or ectopic eruption of the permanent teeth, caries along the line of demarcation, and periodontal disease. Commonly, it dose not need to be treated in primary dentition but in case of permanent dentition, it may be requested to be treated due to esthetics and other problems. In our case, a 8 years old girl showed a Double tooth, we attained the favorable results by performing hemisection with apexification.

• Advances in aircraft and spacecraft science
• /
• v.3 no.3
• /
• pp.351-366
• /
• 2016

Macroperforations improve the sound absorption performance of porous materials in acoustic cavities and in waveguides. In an acoustic cavity, enhanced noise reduction is achieved using porous materials having macroperforations. Double porosity materials are obtained by filling these macroperforations with different poroelastic materials having distinct physical properties. The locations of macroperforations in porous layers can be chosen based on cavity mode shapes. In this paper, the effect of variation of macroporosity and double porosity in porous materials on noise reduction in an acoustic cavity is presented. This analysis is done keeping each perforation size constant. Macroporosity of a porous material is the fraction of area covered by macro holes over the entire porous layer. The number of macroperforations decides macroporosity value. The system under investigation is an acoustic cavity having a layer of poroelastic material rigidly attached on one side and excited by an internal point source. The overall sound pressure level (SPL) inside the cavity coupled with porous layer is calculated using mixed displacement-pressure finite element formulation based on Biot-Allard theory. A 32 node, cubic polynomial brick element is used for discretization of both the cavity and the porous layer. The overall SPL in the cavity lined with porous layer is calculated for various macroporosities ranging from 0.05 to 0.4. The results show that variation in macroporosity of the porous layer affects the overall SPL inside the cavity. This variation in macroporosity is based on the cavity mode shapes. The optimum range of macroporosities in poroelastic layer is determined from this analysis. Next, SPL is calculated considering periodic and nodal line based optimum macroporosity. The corresponding results show that locations of macroperforations based on mode shapes of the acoustic cavity yield better noise reduction compared to those based on nodal lines or periodic macroperforations in poroelastic material layer. Finally, the effectiveness of double porosity materials in terms of overall sound pressure level, compared to equivolume double layer poroelastic materials is investigated; for this the double porosity material is obtained by filling the macroperforations based on mode shapes of the acoustic cavity.

• KOREAN JOURNAL OF CROP SCIENCE
• /
• v.51 no.spc1
• /
• pp.255-258
• /
• 2006

This study was carried out to find the effect of the pinching and planting density on yield of petal and grain in safflower (Caythamus tinctorius L.). The planting density was high effective branch number per $m^2$ compared with pinching, and effective flower bud was most in $270ea/m^2$ in three line planting density, but in case of pinching was few at $186{\sim}223ea/m^2$ Grain yield was increased with 231 kg/10a at double line planting density compared with in 220 kg/10a of control. Petal yield of double line and three line planting density was 25.4 kg/10a and 26.9 kg/10a, it was increased 15, 22% compared with 22.0 kg/10a of control, respectively.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1248-1253
• /
• 2010

In this paper, the compensation algorithm for localization using the concept of equivalent distance rate(AEDR) in order to compensate ranging error in the SDS-TWR(Symmetric Double-Sided Two-Way Ranging) is proposed and the performance of the proposed algorithm is analyzed by the localization experiments. The ranging error of the SDS-TWR in the distance between mobile node and beacon node is measured to average 1m~8m by ranging experiments. But it is confirmed that the performance of the localization by the AEDR is better than that of the SDS-TWR 4 times in university auditorium and corridor, and the localization error of above 3~10m is reduced to average 2m and that of below 3m is reduced to average 1m respectively. It is concluded that the AEDR is superior to the NLOS(Non Line Of Sight) than LOS(Line Of Sight) in performance of ranging compensation for localization, and the AEDR is more helpful to localization systems practically considering the environment of sensor networks is under NLOS.