• 대한기계학회논문집
• /
• 제18권1호
• /
• pp.85-92
• /
• 1994

With the wide application of fiber-reinforced composite meterial in aircraft space structures and robot arms, the design and manufacture of composite joints have become a very important research area because they are often the weakest areas in composite structure. In this paper, the torque transmission capacities of the adhesive tubular single lap joint and double lap joint were studied. The stress and torque transmission capacity of the adhesive joints were analyzed by the finite element method and compared to the experimental results. The torque capacity of the double lap joint was increased 2.7 times over that of the single lap joint. Also, the fatigue limit of the double lap joint was increased 16 times over that of the single lap joint.

• 대한기계학회논문집
• /
• 제18권6호
• /
• pp.1412-1420
• /
• 1994

The adhesively bonded tubular double lap joint has better torque transmission capability and reliability in bonding operation than the single lap joint. In this paper, an analytic solution for the torque transmission capabilities and stress distributions of the adhesively bonded tubular double lap joint was derived assuming the linear properties of the adhesive and adherends. From the calculation, it was found that the torque transmission capabilities of the double lap joint was more than 40% larger compared to that of the single lap joint.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집A
• /
• pp.465-470
• /
• 2001

The adhesively-bonded joints considered in this investigation include single-lap joint and double-lap joint. For an adhesively bonded double-lap joint, end mismatch between the two cuter adherends(upper, lower) can not removed completely although it can be controlled within a manufacturing tolerance. This paper shows that the end mismatch introduces local bending and end mismatch affects the shear and peel stresses in the adhesive. The double-lap joint with an end mismatch is affected of adhesive thickness, material properties of adhesive and adherend etc. Also, we concluded that there are critical value of an end mismatch to provoke the interface fracture.

• 접착 및 계면
• /
• 제7권4호
• /
• pp.13-17
• /
• 2006

The elasto-plastic finite element method (FEM) was used to investigate the effect of off-center recessing location (8 mm length) on the stress distribution in the lap zone of adhesively bonded aluminium double lap joint. The results from simulation showed that the effect of off-cent recessing in bondline of double lap joint in the mid-bondline is not evidently to stress distribution in mid-bondline but the peak stresses both in mid-bondline and in the interface near the adherend side of the joint may increase markedly when an 8 mm length recessing was arranged symmetrical to the point of x =18 mm. When shifting an 8 mm length recess from near left end to the right end of the lap zone, all the highest peak stresses in the mid-bondline occurred under the condition of recess arranged symmetrical to the point of x = 6 mm.

• 대한기계학회논문집
• /
• 제17권8호
• /
• pp.1980-2000
• /
• 1993

The stresses and torque transmission capabilities of adhesively bonded circular, hexagonal and elliptical lap joints were analyzed by the finite element and compared with the experimental results. The adherends of the joints were composed of carbon fiber/epoxy composite shafts and steel shafts. In calculating the torque transmission capabilities, the linear laminate properties of the composite material and the nonlinear shear properties of the adhesive were used. Using this method, the torque transmission capabilities of adhesively bonded lap joints could be obtained within 10% error compared to the experimental results except some single lap joints. The experiments revealed that the hexagonal joint had the best torque transmission capability from the single lap joints and the double lap joint had better torque transmission than the single lap joint.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2002년도 춘계학술발표대회 논문집
• /
• pp.5-8
• /
• 2002

The use of the co-cured joining method for composite structures is attractive due to several benefits. However, since the design stress level in cyclic loads is often smaller than the joint strength obtained from the static tensile load test, it is important to establish proper fatigue design criteria. Although some researchers have reported on co-cured joints, there are only a few papers published on the fatigue characteristics of co-cured joints. In this paper, the effect of bond parameters on the fatigue characteristics of a steel-composite co-cured double lap joint under cyclic tensile loads was experimentally investigated. We considered the surface roughness of the steel adherend and the stacking sequence of the composite adherend as bond parameters. A fatigue failure mechanism of the co-cured double lap joint was explained systematically by investigating the surfaces of failed specimens.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2005년도 춘계학술대회 논문집
• /
• pp.326-331
• /
• 2005

In this study, bearing response in single lap riveted joint is investigated by menas of single lap shear specimens with different types of adherend and fastener. Single lap shear specimen consists of adherend of SUS403 and carbon fabric/epoxy composite. Rivet of Avdel 2691 with 9.6mm diameter is used. Two types of fastener in single lap riveted joint are considered. One is a single lap shear specimen with single fastener, and the other is a single lap shear specimen with double fasteners. Especially, in case of single lap shear specimen with single fastener, the width of the specimen is varied as 2D, 3D, 4D, 6D at a fixed edge distance of 3D. Also the edge distance of the specimen is varied as 1.0D, 1.5D, 2.0D, 2.5D, 3.0D at a fixed width of 4D. In case of single lap shear specimen with double fasteners, two types of specimen are considered. One is a specimen with the width of 6D and edge distance of 3D. The other is a specimen with the width of 4D and edge distance of 2D. Here D designates the hole diameter for riveted joint.

• 한국해양공학회:학술대회논문집
• /
• 한국해양공학회 2002년도 춘계학술대회 논문집
• /
• pp.185-190
• /
• 2002

It has made a special study of bending behavior of F.R.P sandwich beams with bonded 2nd-reinforced plies. Specimens were made of Chopped Mat 300-450, Roving Clothes 570 and the mixture weight ratio of Resin versus hardener was 55:45 for bending tests. it was fabricated by hand lay-up method, hardened for 24 hours in nature, cut specimens according to ASTM standard C393-94 Knowing exact behavior of bonded area's stress and strain depends upon various bonded F.R.P length on which covered lap joint. We also considered shear stress in adhered area and have done computational estimation by ANSYS as well. This study reveals that the length of plies covered lap joint are longer, Failure stresses are remarkably larger.

• Composites Research
• /
• 제19권4호
• /
• pp.23-30
• /
• 2006

극저온 추진제 탱크를 개발하는 과정에서 복합재와 알루미늄 라이너를 접합하기 위한 접착제의 선택은 탱크의 안전성과도 직결된 매우 중요한 문제이다. 따라서 적합한 극저온용 접착제를 선택하기 위해 3종류의 접착필름이 선정되었으며 극저온용으로 개발된 탄소섬유/에폭시와 라이너 재료로 사용되는 알루미늄으로 구성된 양면 겹치기 조인트 시편을 제작하였다. 제작된 시편을 극저온 환경챔버를 사용하여 상온과 $-150^{\circ}C$에서 인장실험을 수행하여 각 접착제의 접착강도를 비교하였으며 파손 특성을 분석하였다. 또한 양면 겹치기 조인트 시편의 각 구성재료의 온도에 따른 기계적 물성변화를 측정하였으며 이를 이용하여 ABAQUS를 통한 유한요소해석을 수행하여 양면 겹치기 조인트 시편의 인장시험결과를 분석하였다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 추계학술발표대회 논문집
• /
• pp.95-98
• /
• 2001

Co-cured joining method is an efficient joining technique because both curing and bonding processes for the composite structures can be achieved simultaneously. It requires neither an adhesive nor a surface treatment of the composite adherend because the excess resin, which is extracted from composite materials during consolidation, accomplishes the co-cured joining process. In this paper, we considered three bond parameters, affecting tensile load bearing capacity of the co-cured single and double lap joints. Filially, we nave presented optimal bonding conditions for co-cured single and double lap joints with steel and composite adherends under tensile loads.