• The Journal of the Korea institute of electronic communication sciences
• /
• v.4 no.2
• /
• pp.75-81
• /
• 2009

In this paper, Microwave doppler radar sensor operated in 10.525GHz is designed by dielectric resonant oscillator. According to doppler effects, a characteristic of Microwave sensor with FMCW was analyzed. The qualities of objects velocity and distance between object and microwave sensor by sensor output frequency difference was measured. As a result of Microwave doppler radar sensor, the prototype sensor is available for indoor burglar alarms and other application through FMCW signal.

• Journal of Digital Convergence
• /
• v.13 no.9
• /
• pp.251-257
• /
• 2015

Recently, techniques for detecting the movement of the object of energy saving, impact prevention, such as automatic door opening and closing has been applied to various fields. Doppler sensor does not receive a large impact on the environment, such as conventional infrared ray sensor, a problem with an ultrasonic sensor as a sensor which can compensate the temperature, noise, dust and so on. In this paper, when the object to be detected, the LED lamp is turned on 24 hours a Doppler sensor ON, if not switch to the OFF state, the illumination of the LED lamp has been developed for controlling the two-stage converter. Doppler sensor developed by applying the converter module and the power-saving control section leader and demonstrated the power savings.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.866-869
• /
• 2015

In this paper, we propose a device for detect front object using low-price the CW Doppler sensor to prevent safety accident such as a bicycle, an electric wheelchair users. For this propose, we develop a signal process board and the object motion detect algorithm using to analyzing output signal of the CW Doppler sensor. Output signal from CW Doppler sensor is analog I and analog Q. The CW Doppler sensor shows phase I and phase Q of object differently when the object approach, stop, drop by sensor. We develop an algorithm that can detect object by discrimination information of phase using the CW Doppler sensor. The verification use firmware of applied hardware and algorithm. Then, the motion information can be confirming output depending on motion object by experiment normally. As a result, we check that the sensing information output by following motion of object and confirm an algorithm and motion of signal processing board.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.57 no.4
• /
• pp.404-407
• /
• 2008

Because of directly receiving the thing in which a microwave is reflected and comparing the frequency, the microwave sensor with doppler effect completely overcomes the problem of the passive infrared sensor. The microwave sensor with doppler effect well operates about a temperature, the dust, and the peripheral noise because of being dull in the most of ambient conditions. The system developed in this research is the electricity saving detection sensor which it senses the real time action of a man as the microwave sensor and automatically turns on the electric lamp and turns off, minimizes the electrical energy consumption. Since the microwave sensor is not influenced in the light, the dust, and the natural element like the ambient temperature, the effectiveness is considered to be superior to the passive infrared sensor being used currently. There was the energy reduction effect more than about 60% in the performed example which established this system. When this was compared with the construction cost, the cost of establishing payback period was about 1-1.5 year. The microwave sensor with doppler effect developed from this research result is convinced in the future to do enough for the electric energy saving.

• Journal of the Institute of Convergence Signal Processing
• /
• v.2 no.2
• /
• pp.75-82
• /
• 2001

In this paper, a transmitter and a receiver using a Gunn diode and SBD was designed and fabricated in X-band. This system detects Doppler shift signal reflected by moving target through the homodyne detection, which is Doppler radar sensor for the measurement of the velocity of moving target. By the experimental results, the oscillating condition of the transmitter was satisfied at about the half wavelength between the supporting post of the Gunn diode in the waveguide and the waveguide short. And using the fabricated Doppler radar sensor, the velocity measurement deviation of moving target was 1.24%.

• Journal of IKEEE
• /
• v.15 no.1
• /
• pp.49-56
• /
• 2011

In this paper, a compact doppler sensor with oscillator type active antenna operating at 2.4GHz frequency band is proposed to measure the distance or speed of a moving object. The active antenna has been realized by oscillator using radiator, patch antenna, as its resonator. The oscillation frequency is shifted depending on approaching of the object, and a detection circuit discriminates the frequency deviation. The oscillator type active antenna has been designed and simulated. The prototype fabricated has a very small circular disk type of diameter 30mm and height 4.2mm. As for antenna performance, broadside radiation pattern with beamwidth of $130^{\circ}$ and oscillation frequency of 2.373GHz has been measured. Test results as a doppler sensor shows that doppler signal voltage of about 190mV has been obtained for conducting plate moving 1 meter away from the sensor. And, doppler signal voltage has been linearly increased to the ground from 4.5m height by free-falling the sensor.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.19 no.3
• /
• pp.623-628
• /
• 2015

The paper produced an application that used Doppler radar sensor to prevent bicycle related accidents. Doppler radar sensor detects any approaching object and gives warning to the user through the danger detection algorithm of the application. The danger detection algorithm determines danger by comparing relative speed using the sensed approaching object and Doppler frequency. It also sends SMS to the preset contact to let him/her be informed of the critical situation in which the user lies when an accident happens. The experiment result showed that the algorithm judged danger by detecting the approach status and speed as well as sent out SMS to the set contact under the assumption that there was an accident.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.419-420
• /
• 2011

• Journal of electromagnetic engineering and science
• /
• v.12 no.4
• /
• pp.234-239
• /
• 2012

This paper presents a compact K-band Doppler radar sensor for human vital signal detection that uses a radar configuration with only single coupler. The proposed radar front-end configuration can reduce the chip size and the additional RF power loss. The radar front-end IC is composed of a Lange coupler, VCO, and single balanced mixer. The oscillation frequency of the VCO is from 27.3 to 27.8 GHz. The phase noise of the VCO is -91.2 dBc/Hz at a 1 MHz offset frequency, and the output power is -4.8 dBm. The conversion gain of the mixer is about 11 dB. The chip size is $0.89{\times}1.47mm^2$. The compact Ka-band Doppler radar system was developed in order to demonstrate remote human vital signal detection. The radar system consists of a Ka-band Doppler radar module with a $2{\times}2$ patch array antenna, baseband signal conditioning block, DAQ system, and signal processing program. The front-end module size is $2.5{\times}2.5cm^2$. The proposed radar sensor can properly capture a human heartbeat and respiration rate at the distance of 50 cm.

• Journal of Digital Convergence
• /
• v.17 no.10
• /
• pp.243-249
• /
• 2019

In this paper, we have developed a device to reduce the standby power consumption that is unnecessarily consumed in unused electrical appliances. The Doppler sensor is used to automatically power off and power off the outlet depending on whether or not a person is present near the outlet. The Doppler sensor uses a coaxial cable trap to design a transmitting antenna and emits a 10 GHz band RF signal and receives a reflected wave signal whose wavelength is reflected from the target object to the receiver to detect an object and recognize human approach. It automatically cuts off and restores standby power to prevent unnecessary power consumption, saving energy and developing a standby power automatic shutdown and recovery device that can prevent the risk of large fires caused by leakage current.