• International Journal of Computer Science & Network Security
• /
• v.23 no.6
• /
• pp.27-34
• /
• 2023

This paper proposed an Inter-Carrier-Interference (ICI) Canceling Orthogonal Frequency Division Multiplexing (OFDM) receiver for 5G mobile system to support 500 km/h linear motor high speed terrestrial transportation service. A receiver in such high-speed train sees the transmission channel which is composed of multiple Doppler-shifted propagation paths. Then, a loss of sub-carrier orthogonality due to Doppler-spread channels causes ICI. The ICI Canceler is realized by the following three steps. First, using the Demodulation Reference Symbol (DMRS) pilot signals, it analyzes three parameters such as attenuation, relative delay, and Doppler-shift of each multi-path component. Secondly, based on the sets of three parameters, Channel Transfer Function (CTF) of sender sub-carrier number 𝒏 to receiver sub-carrier number 𝒍 is generated. In case of 𝒏≠𝒍, the CTF corresponds to ICI factor. Thirdly, since ICI factor is obtained, by applying ICI reverse operation by Multi-Tap Equalizer, ICI canceling can be realized. ICI canceling performance has been simulated assuming severe channel condition such as 500 km/h, 2 path reverse Doppler Shift for QPSK, 16QAM, 64QAM and 256QAM modulations. In particular, for modulation schemes below 16QAM, we confirmed that the difference between BER in a 2 path reverse Doppler shift environment and stationary environment at a moving speed of 500 km/h was very small when the number of taps in the multi-tap equalizer was set to 31 taps or more. We also confirmed that the BER performance in high-speed mobile communications for multi-level modulation schemes above 64QAM is dramatically improved by the use of a multi-tap equalizer.

• Journal of Advanced Navigation Technology
• /
• v.8 no.2
• /
• pp.136-144
• /
• 2004

In this paper, we present an improved channel estimation method for orthogonal frequency division multiplexing systems using pilot-symbol-aided parameter estimation. Conventional linear minimum mean square error(LMMSE) channel estimation method uses only pilot symbols for channel estimation. So, as the fading channel varies rapidly, a performance is decreased. We proposed a channel estimation method, which estimates channel attenuation in the middle of pilots using pilot symbols and then estimates the whole channel attenuation with pilots and estimated channel attenuation. Compared with conventional LMMSE channel estimation method, the proposed method is significantly robust in a rapid fading channel with high Doppler frequency and delay spread.

• Proceedings of the KSRS Conference
• /
• 2007.10a
• /
• pp.625-628
• /
• 2007

We present an efficient and robust technique to estimate the velocity of moving targets from a single SAR image. In SAR images, azimuth image shift is a well known phenomenon, which is observed in moving targets having slant-range velocity. Most methods estimated the velocity of moving targets from the distance difference between the road and moving targets or between ship and the ship wake. However, the methods could not be always applied to moving targets because it is difficult to find the road and the ship wake. We adopted a method estimating the velocity of moving targets from azimuth differentials of range-compressed image. This method is based on an assumption that Doppler center frequency shift of moving target causes a phase difference in azimuth differential values. The phase difference is linearly distorted by Doppler rate due to the geometry of SAR image. The linear distortion is eliminated from phase removal procedure, and the constant phase difference is estimated. Finally, range velocity estimates for moving targets are retrieved. This technique is tested using an ENVISAT ASAR image in which several unknown ships are presented. The theoretical accuracy of this technique is discussed by SAR simulation. The advantages and disadvantages of this method over the conventional method are also discussed.

• IEIE Transactions on Smart Processing and Computing
• /
• v.3 no.3
• /
• pp.142-152
• /
• 2014

Vehicular Ad-hoc Networks (VANETs) are comprised of wireless mobile nodes characterized by a randomly changing topology, high mobility, availability of geographic position, and fewer power constraints. Orthogonal Frequency Division Multiplexing (OFDM) is a promising candidate for the physical layer of VANET because of the inherent characteristics of the spectral efficiency and robustness to channel impairments. The susceptibility of OFDM to Inter-Carrier Interference (ICI) is a challenging issue. The high mobility of nodes in VANET causes higher Doppler shifts, which results in ICI in the OFDM system. In this paper, a frequency domain com-btype channel estimation was used to cancel out ICI. The channel frequency response at the pilot tones was estimated using a Least Square (LS) estimator. An efficient interpolation technique is required to estimate the channel at the data tones with low interpolation error. This paper proposes a robust interpolation technique to estimate the channel frequency response at the data subcarriers. The channel induced noise tended to degrade the Bit Error Rate (BER) performance of the system. Parallel concatenated Convolutional codes were used for error correction. At the decoding end, different decoding algorithms were considered for the component decoders of the iterative Turbo decoder. A performance and complexity comparison among the various decoding algorithms was also carried out.

• The Journal of the Acoustical Society of Korea
• /
• v.28 no.4
• /
• pp.336-342
• /
• 2009

A conventional Closest Point of Approach (CPA) analysis allows a non-maneuvering moving source that is radiating a constant frequency tone to be located using doppler shifted frequency measurements obtained by a stationary receiver. The original frequency, relative speed of the target, time at the CPA, and range from the CPA to the sensor are estimated by the conventional CPA. However, this paper proposes a new CPA analysis that allows the motion parameters of a target to be estimated using the bearing and frequency measurements obtained by a moving receiver that has a constant velocity. The validity of the proposed estimation scheme is confirmed through a performance analysis and simulation study.

• Journal of Institute of Control, Robotics and Systems
• /
• v.14 no.7
• /
• pp.689-694
• /
• 2008

This paper proposes a roll rate estimation method for spinning vehicles. The carrier phase and frequency variations caused by spinning of vehicles are observed and the roll rate estimator is designed on the observation. The roll rate estimator consists of phase detector and zero crossing counter. The phase detector computes phase variation using in-phase and quadrature value from the correlator. By using zero crossing counter, the roll rate can be estimated since the output of phase detector is changed in proportion to the roll rate. Experiment a results show that estimated roll rate error is smaller than 0.0578Hz.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.36 no.2A
• /
• pp.91-99
• /
• 2011

Several repeater systems are used to enhance the cell coverage to location such as shadow and rural areas in mobile systems. But the general RF repeater solutions are not suitable for high power outdoor environment because it has the weakness such as self oscillation problem With adoption of a adaptive digital filter technology, feedback interference cancellation repeater prevents oscillation by detecting and canceling the unwanted feedback signal between transmission and receiver antenna. In this paper, dual NLMS based interference cancellation method is proposed and the step size adaptation can be implemented by the estimation of the feedback channel Doppler frequency characteristics. The performance of the proposed algorithm is quantified via analysis and simulation for the static and multipath fading feedback channels.

• Journal of the Institute of Electronics Engineers of Korea TE
• /
• v.37 no.2
• /
• pp.54-61
• /
• 2000

This paper presents the performance evaluation of channel estimation algorithm using RLS algorithm lot W-CDMA reverse link over Rayleigh fading channels. By obtaining BER(Bit Error Rate) performance through computer simulations, the RLS(Recursive Least Square) algorithm is compared with the existing WMSA(Weighted Averaging)(K=1,3) and constant gain algorithm. The channel structure, modulation and pilot patterns are applied to the ARIB (Association of Radio Industries and Business) and 3GPP (3rd Generation Partnership Project) ITU-R proposal for the IMT-2000. The BER performance of RLS algorithm with linear interpolation is similar to that of WMSA(K=1) and slightly superior to that of constant gain algorithm at low Doppler frequencies. Also, RLS algorithm performance is better than that of the WMSA(K=1,3) and constant gain algorithms about 4dB at BER=2.0$\times$$10^{-2}$ and Doppler frequencies $F_D$=320Hz. With increasing Doppler frequency, therefore, the BER performance of RLS algorithm with linear interpolation is superior to WMSA(K=L.3) and constant rain algorithms.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.8 no.2
• /
• pp.126-136
• /
• 1997

When we apply the spectrally efficient quadrature amplitude modulation(QAM) to mobile communications, it is necessary to estimate and compensate the channel charac- teristics. In this paper, a new type fading estimation method for PSAM using sinc function is presented. Gaussian interpolation method has a drawback that the performance degrades rapidly if pilot symbol period increases even though pilot sysbol period is less than Nyquist sampling rate. The Wiener filter method does not degrade until pilot symbol period is equal to the Nyquist sampling rate. It is difficult for Wiener filter method to be applied to real system because autocorrelation function of channel gain, Doppler frequency and SNR(signal to noise ratio) must be known to optimize the filter coefficients. But proposed method has a similar performance to the Wiener filter method, and does not need to know the autocorrelation function of channel gain, the doppler frequency and SNR. Therefore the proposed method cna be applied to real system easily.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.9C
• /
• pp.729-734
• /
• 2010

In the initial stage of the communications between a base station and a satellite transponder, the base station transmits the frequency-sweeping un-modulated up-link carrier within a certain frequency range to acquire the doppler frequency shift and signal power between the base station and the satellite in orbital flight. The satellite transponder acquires and tracks the carrier in order to initialize the communication. To control such initialization process, the satellite receiver should analyze the input carrier signal in various ways. This paper presents an SNR estimation algorithm to control the initialization process. The proposed algorithm converts the input signal into the baseband polar coordinate representation and estimates the SNR via the statistics of the angular signal components as well as the status parameters to control the receiver. The Monte-Carlo simulations shows the validity of the estimation proposed.