• KIEE International Transactions on Power Engineering
• /
• 제4A권4호
• /
• pp.201-206
• /
• 2004

With the advent of distributed generation, power systems in general are impacted in regards to stability and power quality. Distributed generation has positive impacts on system restoration following a fault, higher reliability, and mitigation of effect due to voltage sag. However, distributed generation also has negative impacts on the decrease of reliability such as changes of protective device setting and mal-operation. Because bulk power systems consist of various sources and loads, it is complicated to analyze power systems that have distributed generation. The types of distributed generation usually are classified as the rotating machinery system and the inverter-based system. In this paper, distributed generation is designed as a synchronous generator, and the distribution system with its distributed generation model is simulated using EMTP. In addition, this paper shows the simulation results according to the types of distributed generation

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 2002년도 ITC-CSCC -2
• /
• pp.1324-1326
• /
• 2002

This paper concerns the development of distributed interactive simulation of a road traffic system. The simulation involved models of multiple and distributed road vehicles running on different locations. The simulation system represented a traffic system as if the distributed simulation models were in the same environment. The development of the distributed road traffic simulation was based on High Level Architecture (HLA), a state-of-the-art IEEE standard for the distributed and real-time simulation. Other work concerned modeling and simulating the road vehicles and building the map database for the virtual distributed shared environment. The information used in the simulation system was only in X-axis and Y-axis as the insignificant data in the Z-axis was omitted to simplify the simulation. However, the traffic system has visualized a 3-D coordinate system. The road vehicle models were able to avoid collision. The next direction of a vehicle can be chosen from the provided choices of further paths.

• 전기학회논문지
• /
• 제68권4호
• /
• pp.513-522
• /
• 2019

We calculate the benefit of distributed combined heat power generators from avoiding a transmission expansion cost by building distributed generators near electricity demand centers. We determine a transmission expansion plan by solving a mixed integer linear problem, where we modify capacities of existing transmission lines and build new transmission lines. We calculate the benefit by comparing the sum of generation and transmission expansion costs with or without distributed generators through two simulation frames. In the first frame, for the current demand, we substitute existing distributed generators for non-distributed generators and measure an additional cost to balance the generation and demand. In the second frame, for increased future demand, we compare the cost to invest only in distributed generators to the cost to invest only in non-distributed generators. As a result, we show that the distributed generators have at least 5.8 won/kWh of the benefit from avoiding the transmission expansion cost.

• KIEE International Transactions on Power Engineering
• /
• 제4A권3호
• /
• pp.122-128
• /
• 2004

With the advent of distributed generation, power systems are fundamentally impacted in regards to stability and power quality. Distributed generation has a positive impact on system restoration following a fault, higher reliability, and mitigation of effect due to voltage sag. However, distributed generation also has a negative impact on decrease of reliability such as changes of protective device setting and mal-operation. Because bulk power systems consist of various sources and loads, it becomes complicated to analyze a power system with distributed generation. The types of distributed generation are usually classified by both rotating machinery and the inverter-based system. In this paper, distributed generation is designed by rotating machinery, and the distributed system having a model of the distributed generation is simulated using EMTP. In addition, this paper presents the simulation results according to the types of distributed generation.

• Journal of information and communication convergence engineering
• /
• 제1권1호
• /
• pp.12-22
• /
• 2003

Real-time(RT) object-oriented(OO) distributed computing is a form of RT distributed computing realized with a distributed computer system structured in the form of an object network. Several approached proposed in recent years for extending the conventional object structuring scheme to suit RT applications, are briefly reviewed. Then the approach named the TMO (Time-triggered Message-triggered Object) structuring scheme was formulated with the goal of instigating a quantum productivity jump in the design of distributed time triggered simulation. The TMO scheme is intended to facilitate the pursuit of a new paradigm in designing distributed time triggered simulation which is to realize real-time computing with a common and general design style that does not alienate the main-stream computing industry and yet to allow system engineers to confidently produce certifiable distributed time triggered simulation for safety-critical applications. The TMO structuring scheme is a syntactically simple but semantically powerful extension of the conventional object structuring approached and as such, its support tools can be based on various well-established OO programming languages such as C++ and on ubiquitous commercial RT operating system kernels. The Scheme enables a great reduction of the designers efforts in guaranteeing timely service capabilities of application systems

• 전기학회논문지
• /
• 제67권8호
• /
• pp.1002-1008
• /
• 2018

Fault Ride Through(FRT) requirement prevents disconnections of distributed generations during the specific time on disturbance condition for system stability. However, since there is a limitation to the FRT capability of distributed generation, and the protection system needs to clear the fault quickly before the distributed generation is disconnected. Therefore, this paper proposes a novel optimal setting method of directional overcurrent relay considering FRT of distributed generation. The proposed method reduces the probability of disconnections of the distributed generation in disturbance without additional equipment considering the FRT capability of the distributed generation by calculating the optimal relay setting through the Genetic Algorithm(GA).

• 한국정밀공학회지
• /
• 제31권11호
• /
• pp.1015-1021
• /
• 2014

This paper proposes the center distributed embroidery machine structure with 1,500 RPM, 52 heads for productivity and large sized embroidery goods. The synchronous velocity controller is adopted for control of the 2-axis distributed embroidery machine and the DOB(Disturbance Observer) is also adopted for minimizing disturbances caused by needle cams. For driving experiments of 2-axis center distributed driving structure, two conventional 26 heads 1,500RPM embroidery machines are used. It was shown that the center distributed driving structure with 2-axis synchronous control can be one way for implementing a large embroidery machine.

• Earthquakes and Structures
• /
• 제5권2호
• /
• pp.239-259
• /
• 2013

Typically, beams that form part of structural systems are subjected to vertical distributed loading along their length. Distributed loading affects moment and shear distribution, and consequently spread of inelasticity, along the beam length. However, the finite element models developed so far for seismic analysis of frame structures either ignore the effect of vertical distributed loading on spread of inelasticity or consider it in an approximate manner. In this paper, a beam-type finite element is developed, which is capable of considering accurately the effect of uniform distributed loading on spreading of inelastic deformations along the beam length. The proposed model consists of two gradual spread inelasticity sub-elements accounting explicitly for inelastic flexural and shear response. Following this approach, the effect of distributed loading on spreading of inelastic flexural and shear deformations is properly taken into account. The finite element is implemented in the seismic analysis of plane frame structures with beam members controlled either by flexure or shear. It is shown that to obtain accurate results the influence of distributed beam loading on spreading of inelastic deformations should be taken into account in the inelastic seismic analysis of frame structures.

• ETRI Journal
• /
• 제43권2호
• /
• pp.221-231
• /
• 2021

To resolve energy depletion issues in massive Internet of Things sensor networks, we developed a set of distributed energy beamforming methods with one-bit feedback and clustering for multi-node wireless energy transfer, where multiple singleantenna distributed energy transmitters (Txs) transfer their energy to multiple nodes wirelessly. Unlike previous works focusing on distributed information beamforming using a single energy receiver (Rx) node, we developed a distributed energy beamforming method for multiple Rx nodes. Additionally, we propose two clustering methods in which each Tx node chooses a suitable Rx node. Furthermore, we propose a fast distributed beamforming method based on Tx sub-clustering. Through computer simulations, we demonstrate that the proposed distributed beamforming method makes it possible to transfer wireless energy to massive numbers of sensors effectively and rapidly with small implementation complexity. We also analyze the energy harvesting outage probability of the proposed beamforming method, which provides insights into the design of wireless energy transfer networks with distributed beamforming.

• International Journal of CAD/CAM
• /
• 제3권1_2호
• /
• pp.51-60
• /
• 2003

The growth of the World Wide Web and the advances in high-speed network access have greatly changed existing CAD/CAE environment. The WWW has enabled us to share various distributed product data and to collaborate in the design process. An international standard for the product model data, STEP, and a standard for the distributed object technology, CORBA, are very important technological components for the interoperability in the advanced design and manufacturing environment. These two technologies provide background for the sharing of product data and the integration of applications on the network. This paper describes a distributed CAD/CAE environment that is integrated on the network by CORBA and product model data standard STEP. Several prototype application modules were implemented to verify the proposed concept and the test result is discussed. Finite element analysis server are further distributed into several frontal servers for the implementation of distributed parallel solution of finite element system equations. Distributed computation of analysis server is also implemented by using CORBA for the generalization of the proposed method.