• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.10 no.2
• /
• pp.77-85
• /
• 2012

This study was carried out to remove (/recover) the uranium from the Uranium-bearing Lime Precipitate (ULP). An oxidative dissolution of ULP with carbonate-acidified precipitation and a dissolution of ULP with nitric acid-hydrogen peroxide precipitation were discussed, respectively. In point of view the dissolution of uranium in ULP, nitric acid dissolution which could dissolved more than 98% of uranium was more effective than carbonate dissolution. However, in this case, uranium was dissolved together with a large amount of impurities such as Al, Ca, Fe, Mg, Si, etc. and some impurities were also co-precipitated with uranium during a hydrogen peroxide precipitation. On the other hand, in the case of carbonate dissolution-acidified precipitation, U was dissolved less than 90%. Therefore, it was less effective than nitric acid dissolution for the volume reduction of radioactive solid waste. However, it was very effective to recover the pure uranium, because impurities were hardly dissolved and hardly co-precipitated with uranium.

• Korean Journal of Materials Research
• /
• v.26 no.5
• /
• pp.235-240
• /
• 2016

Appropriate thermo-mechanical properties of nickel-based superalloys are achieved by heat treatment, which induces precipitation and solid solution hardening; thus, information on the temperature ranges of precipitation and dissolution of the precipitates is essential for the determination of the heat treatment condition. In this study, thermal analyses of nickel-based superalloys were performed by differential scanning calorimetry method under conditions of various heating rates of 5, 10, 20, or 40K/min in a temperature range of 298~1573K. Precipitation and dissolution temperatures were determined by measuring peak temperatures, constructing trend lines, and extrapolating those lines to the zero heating rate to find the exact temperature under isothermal condition. Determined temperatures for the precipitation reactions were 813, 952, and 1062K. Determined onset, peak, and offset temperatures of the first dissolution reaction were 1302, 1388, and 1406K, respectively, and those values of the second dissolution reaction were 1405, 1414, and 1462K. Determined solvus temperature was 1462K. The study showed that it was possible to use a simple method to obtain accurate phase transition temperatures under isothermal condition.

• Journal of environmental and Sanitary engineering
• /
• v.14 no.3
• /
• pp.116-122
• /
• 1999

The purpose of this study is to develop new process named "hydrogen peroxide dissolution method". This process used hydrogen peroxide, which is harmless to human body and oxidize molybdenum wire selectively.The advantages of hydrogen peroxide dissolution method were no discharge of noxious matter when dissolution of molybdenum wire which used as the center supporter, reactions occur in room temperature and easy to recover dissolved molybdenum. This study was aimed at gathering the basic data of molybdenum wire dissolution-recovery process and proposes the reaction condition of molybdenum wire dissolution-recovery process and the factors influencing those reactions. The results were as follows:1. In the dissolution of molybdenum wire, the early condition of reaction was $15^{\circ}C$, and the temperature condition of state was $32^{\circ}C$. 2. 1) In the GSL-60W type, P.W.(Piece weight) was 11.89mg, C.R. was $65.6\Omega$. 2) In the FL-20W type, P.W. was 11.60mg, C.R. was $4.6\Omega$. 3. The molybdenum of process water was treated of a precipitation after dry and after stagnation in the one day, the molybdenum of upper water was treated of precipitation after dry and after congelation.

• Economic and Environmental Geology
• /
• v.50 no.6
• /
• pp.509-515
• /
• 2017

Quartz is the most abundant mineral in the Earth's continental crust. Therefore, understanding of quartz dissolution and precipitation is very important to know about weathering processes and interactions between rocks and water in hydrothermal and metamorphic environments. This paper presents a basic review on the research about quartz dissolution mechanism under various physico-chemical conditions. We rearranged the relationship between each physico-chemical factor and dissolution mechanism from the results of previous researchers in this paper. From this result, we understood that quartz dissolution and precipitation are affected by each factor such as temperature, pH, and applied stress conditions at contact point. In particular, we recognized that the high pH and temperature conditions have different anion concentrations on mineral's surface. As a result, high pH and temperature conditions have a better effect than applied stress condition to the quartz dissolution mechanism.

• Journal of the Mineralogical Society of Korea
• /
• v.9 no.2
• /
• pp.71-81
• /
• 1996

Dissolution experiments were conducted to understand chemical nature of weathering of anorthosite from the Hadong area. Anorthosite and plagioclase from it were reacted with HCl or KOH solutions under various conditions concerning such as grain size, initial pH of solutions, and shaking Average composition of plagioclase used in the experiment was Na0.32Ca0.71Al1.71Si2.28O8.Under acidic conditions, solution pH increases rapidly in the initial stage and then gradually to reach palteau. Shaking agitates the reaction rate in the initial stage but does not affect after the system reached steady state. Ca and si concentrations show rapid increase and then gradual increase. Al concentration increases rapidly in the early stage and then decreases. Later decrease was interpreted as the precipitation of an Al-bearing material. Different dissolution rates of different constituents of plagioclase together the with precipitation of al-bearing material might be responsible for the non-stoichiometric dissolution of plagioclase.X-ray diffraction analyses on anorthosite before and after dissolution experiment show dissolution rates differ with different lattice planes of plagioclase. It suggests the crystallographic control on dissolution reaction. X-ray photoelectron spectroscopic result shows that the average composition of plagioclase surface reacted with HCL of initial pH 1.97 for 2000 hours is Na0.20Ca0.26Al1.7Si2.3O8. It means that Na- and Ca-depleted H-feldspar is developed without Al-depleted layer on the surface of plagioclase by reaction with HCl and that dissolution reaction takes place sparsely on the surface of plagioclase. Al and Si are dissolved preferentially over Ca from anorthosite powder in KHO solution. Reaction of acid-reacted anorthosite with KOH solution shows the same Si dissolution behavior as in the fresh anorthosite. This indicates that the Al-depleted and Si-enriched layer does not build up on the acid-reacted surface.

• Journal of the Korean Society for Heat Treatment
• /
• v.6 no.3
• /
• pp.138-143
• /
• 1993

Effects of aging treatment on the microstructural evolution of a rapidly solidified Al-Li-Cu alloy were investigated by differential scanning calorimetry (DSC) and transmission electron microscopy(TEM). It was found that the precipitation sequence was: supersaturated solid solution ${\alpha}^{\prime}$ ${\rightarrow}$ metastable ${\delta}^{\prime}$ + stable precipitate $T_1$ ${\rightarrow}$ stable precipitates ${\delta}+T_1$. Two exothermic and two endothermic peaks are detected by DSC analysis. The two exothermic and endothermic peaks corresponded to ${\delta}^{\prime}$ and ${\delta}+T_1$ precipitation and dissolution reactions respectively. The enthalpy of ${\delta}^{\prime}$ precipitation decreased with increasing of aging temperature and time until the finishing point of precipitation. The activation energy for precipitation of ${\delta}^{\prime}$ was measured as 80KJ/mol and the energy for dissolution was 93KJ/mol. These values arc higher than those of AI-Li binary alloy. Peak hardness value (Hv 170) was obtamed at $210^{\circ}C$ for 1hr aging treatment which coincided with finishing point of ${\delta}^{\prime}$ precipitation.

• Korean Journal of Metals and Materials
• /
• v.49 no.12
• /
• pp.917-923
• /
• 2011

Dissolution and precipitation behaviors of complex carbonitrides in austenite of a V-Nb microalloyed steel were quantitatively examined through electrical resistivity measurement and transmission electron microscopy. The electrical resistivity increased with solution treatment temperature up to $1240^{\circ}C$ and then was saturated at $225n{\Omega}m$ for a holding time of 10 min. The electrical resistivity method was also used to quantitatively measure the isothermal precipitation kinetics of the complex carbonitrides in austenite. Nb-rich precipitates were observed in austenite at the early stages of precipitation, but Nb was replaced by V up to the equilibrium amount within the precipitates with further holding time. The time-temperature-precipitation diagram showed a C-type curve; nose temperature and its incubation time were $900^{\circ}C$ and 100 s, respectively.

• Korean Journal of Materials Research
• /
• v.30 no.9
• /
• pp.474-479
• /
• 2020

The effect of precipitation and dissolution of Si on the thermal diffusivity in the Al-Si alloy system is reported in this study and solution heat treatment followed by aging treatment is carried out to determine the effects of heat treatment on the thermal characteristics. The solution treatment is performed at 535 ℃ for 4 and 10 h and then the specimens are cooled by rapid quenching. The samples are aged at 300 ℃ for 4 h to precipitate Si solute. The addition of 9 wt% silicon contents makes the thermal diffusivity decrease from 78 to 74 mm/s² in the cases of solid solution treated and quenched samples. After quenching and aging, the Si solute precipitates on the Al matrix and increases the thermal diffusivity compared with that after the quenched state. In particular, the increase of the thermal diffusivity is equal to 10 mm/s² without relation to the Si contents in the Al-Si alloy, which seems to corresponded to solute amount of Si 1 wt% in the Al matrix.

• Proceedings of the KSEEG Conference
• /
• 2005.04a
• /
• pp.34-34
• /
• 2005

• Bulletin of the Korean Chemical Society
• /
• v.19 no.9
• /
• pp.1009-1011
• /
• 1998