• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.12 no.4
• /
• pp.168-180
• /
• 2000

In the Part I, the three dimensional model testing with NNW deep water wave direction gave the results such that the occurrence of breaking waves over the peak of Ear-Do caused very small wave height at the structure position. But the measured wave forces were rather greater than the calculated forces based on deep water wave height. Furthermore, It was also perceived that the time series of the forces looked like corresponding to the case that waves were superimposed by an unidirectional current. In the present Part II, the current is presumed to be a flow secondly induced by breaking waves, and an extensive study to clarify the current in a quantitative sense is performed through numerical analysis and hydraulic experiment. The results showed that a strong circulation can surely occur in the vicinity of the structure due to radiation stress differentials given by the breaking waves. It was also recognized that the velocity of the induced current varied with the magnitude of energy dissipation rate introduced in the numerical analysis. The numerical analysis was tuned adjusting the dissipation rate so that the calculated wave field could closely match with the experimental results of Part I. The fluid force (in prototype) for the optimal match showed approximately 2.2% increased over the calculated value based on the deep water wave height (24.6m) whereas the force corresponding to the average of the experimental values showed the increase of about 13.0%.

• Korean Journal of Applied Biomechanics
• /
• v.22 no.4
• /
• pp.379-386
• /
• 2012

The aim of this study was to investigate and identify the differences in lower extremity energy dissipation strategies between drop-landing and countermovement-jump maneuvers. Fourteen recreational athletes(Age : $23.3{\pm}2.1years$, Height : $172.3{\pm}4.0cm$, Weight : $69.2{\pm}4.7kg$) were recruited and instructed to perform drop-landing from 45 cm height and countermovement-jump from 45 cm to 20 cm height. The landing phase was taken as the time between initial contact and peak knee flexion. A motion-capture system consisting of eight infra-red cameras was employed to collect kinematics data at a sampling rate of 200 Hz and a force-plate was used to collect GRF data at a sampling rate of 2000 Hz. Paired t-test was performed to determine the difference in kinematics and kinetics variables between each task. During the countermovement-jump task, all of lower extremity joint ROM and the hip joint eccentric moment were decreased and the ankle joint plantarflexion moment was increased than drop-landing task. In the eccentric work during countermovement-jump task, the ankle joint displayed greater while knee and hip joint showed lesser than drop-landing. Therefore, the knee joint acted as the key energy dissipater during drop-landing while the ankle joint contributed the most energy dissipation during countermovement-jump. Our findings collectively indicated that different energy dissipation strategies were adopted for drop-landing and countermovement-jump.

• Korean Journal of Environmental Agriculture
• /
• v.42 no.2
• /
• pp.131-138
• /
• 2023

The biological half-life and dissipation rate of azoxystrobin in crown daisy were calculated to establish the pre-harvest residue limits (PHRLs). The pesticide residues were calculated after washing with five different processes to propose an effective process in the household and conducted a risk assessment to confirm dietary safety. Azoxystrobin was sprayed according to the critical good agricultural practices (cGAP) in two different field trials, and the samples were harvested 7 times. The limit of quantitation was 0.02 mg/kg, and the mean recoveries of azoxystrobin were within the range of 70~120% with below 20% coefficient variation at the concentration of 0.02 and 0.2 mg/kg . The biological half-lives were 7.4 and 4.7 days, and the dissipation rate constants were 0.0872 and 0.1217 in fields 1 and 2, respectively. The average removal rates were 58.13~78.13% by the different washing processes, and there were significant differences between the washing processes (one-way ANOVA analysis and post-hoc Duncan test, p-value<0.05). The residues of azoxystrobin in crown daisy were safe levels from farm to fork after application with the critical good agricultural practice (cGAP) registered in Korea.

• Proceedings of the IEEK Conference
• /
• 2000.11b
• /
• pp.164-167
• /
• 2000

This paper introduces the design of high-speed analog-to-digital converter for hard disk drive (HDD) read channel. This is based on autozero technique for low-error rate, and Double Speed Dual ADC(DSDA) technique lot efficiently increasing the conversion speed of A/D converter. This An is designed by 6bit resolution, 800M sample/s maximum conversion rate, 390㎽ power dissipation, one clock cycle latency in 0.65 $\mu\textrm{m}$ CMOS technology.

• Transactions of Materials Processing
• /
• v.10 no.4
• /
• pp.347-354
• /
• 2001

Compression tests were carried out to investigate the hot-deformation behavior of Ti-6Al-4V alloy in the temperature range of $915^{\circ}C$ to $1015^{\circ}C$ and the strain rate range of $10^{-3}s^{-i}$ to $10s^{-1}$. Under the given test conditions, the hot-deformation of Ti-6Al-4V alloy was mainly led by dynamic recovery rather than by dynamic recrystallization. The activation energy for the plastic deformation in $\alpha+\beta$ field was about 894 kJ/mol and $\beta$ field was 332kJ/mo1. Processing map for hot working are developed on the basis of the variations of efficiency of power dissipation($\eta$=2m/m＋1) and flow instability criterion using the dynamic material model. The optimum process condition in the ($\alpha＋\beta$) field was obtained at the temperature ranges of $930^{\circ}C$ to $955^{\circ}C$$^{\circ}C$ and a strain rate of $10^{-3}s{-1}$.

• 한국연소학회:학술대회논문집
• /
• 2004.06a
• /
• pp.102-111
• /
• 2004

Partial quenching structure of turbulent diffusion flames in a turbulent mixing layer is investigated by the method of flame hole dynamics to develope a prediction model for the turbulent lift off. The present study is specifically aimed to remedy the problem of the stiff transition of the conditioned partial burning probability across the crossover condition by adopting level-set method which describes propagating or retreating flame front with specified propagation speed. In light of the level-set simulations with two model problems for the propagation speed, the stabilizing conditions for a turbulent lifted flame are suggested. The flame hole dynamics combined with level-set method yields a temporally evolving turbulent extinction process and its partial quenching characteristics is compared with the results of the previous model employing the flame-hole random walk mapping. The probability to encounter reacting' state, conditioned with scalar dissipation rate, demonstrated that the conditional probability has a rather gradual transition across the crossover scalar dissipation rate in contrast to the stiff transition of resulted from the flame-hole random walk mapping and could be attributed to the finite response of the flame edge propagation.

• Journal of Hydrogen and New Energy
• /
• v.18 no.3
• /
• pp.265-274
• /
• 2007

A study has been conducted to clarify NO emission behavior through preferential diffusion effects of $H_2$ and H in methane-hydrogen diffusion flames. A comparison is made by employing three species diffusion models. Special concerns are focused on what is the deterministic role of the preferential diffusion effects in flame structure and NO emission. The behavior of maximum flame temperatures with three species diffusion models is not explained by scalar dissipation rate but the nature of chemical kinetics. The preferential diffusion of H into reaction zone suppresses the populations of the chain carrier radicals and then flame temperature while that of $H_2$ produces the increase of flame temperature. These preferential diffusion effects of $H_2$ and H are also discussed about NO emissions through the three species diffusion models.

• Proceedings of the IEEK Conference
• /
• 2002.07b
• /
• pp.856-859
• /
• 2002

This paper proposes a high-performance VLSl architecture using distributed arithmetic for higher-order FIR filters with complex coefficients. For the purpose of realizing high sampling rate with small latency in high-order filters, we apply distributed arithmetic[1］. Moreover, in order to decrease drastically the power dissipation, the structure applying not ROM's but optimum function circuits which we have previously proposed, is utilized［2]［3］. However, this structure increases in the number of adders as compared to the conventional structure applying ROM's. In order to realize a more effective method for further higher-order filter, we propose newly an implementation applying two methods which have large effects on the unit using the adders. First , we propose an implementation applying SFAs(Serial Full Adders) and SFSs(Serial Full Subtractors). Second, we propose a structure applying proposed 4-2 adders. Finally, it is shown that the proposed architecture is an effective way to realize low power dissipation and small latency while the sampling rate is kept constant for further higher-order filters with complex coefficients.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.10
• /
• pp.1200-1205
• /
• 2014

The effect of nanofluids on the heat transfer performance of a pulsating heat pipe has been experimentally investigated. Water-based diamond nanofluid and aluminium oxide ($Al_2O_3$) nanofluid were tested in the concentration range of 0.5-5%. The pulsating heat pipe was constructed using clear Pyrex tubes of 1.85 mm in inner diameter in order to visualize the pulsating action. The total number of turns was eight each for heated and cooled parts. The supply temperatures of heating water and cooling water were fixed at $80^{\circ}C$ and $25^{\circ}C$ respectively. The liquid charging ratio of the nanofluid was 50-70%. The test results showed that the case of 5% concentration of diamond nanofluid showed 18% increase in heat transfer rate compared to pure water. The case of 0.5% concentration of $Al_2O_3$ nanofluid showed 24% increase in heat transfer rate compared to pure water. But the increase of $Al_2O_3$ nanofluid concentration up to 3% did not show further enhancement in heat transfer. It is also observed that the deposited nanoparticles on the tube wall played a major role in enhanced evaporation of working fluid and this could be the reason for the enhancement of heat transfer by a nanofluid, not the enhanced thermal conductivity of the nanofluid.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.6
• /
• pp.1596-1608
• /
• 1993

Low Reynolds number second moment turbulence model which be applicable to the fine gird near the wall region was developed. In this model, turbulence model coefficients in the pressure strain model of the Reynolds stress equation was expressed as functions of turbulence Reynolds number $R_{t}\equivk^{2}/(\nu\varepsilon)).$ In the derivation procedure of the present low Reynolds number algebraic stress model, Laufer's near wall experimental data on Reynolds stresses were curve fitted as functions of R$_{t}$ and the resulting simultaneous equations of the model coefficients were solved by using the boundary conditions at wall and high Reynolds number limiting conditions. Predicted Reynolds stresses and dissipation rate of turbulent kinetic energy etc. in the 2 dimensional parallel, plane channel flow and pipe flow were compared with the preditions obtained by employing the Launder-Shima model, standard algebraic stress model and several experimental data. Results show that all the Reynolds stresses and dissipation rate of turbulent kinetic energy predicted by the present low Reynolds number algebraic stress model agree better with the experimental data than those predicted by other algebraic stress models.