• 한국레이저가공학회지
• /
• 제14권4호
• /
• pp.9-13
• /
• 2011

The solar panel that consists of copper plate and copper tube was successfully welded by ultrasonic seam welding. However it was not only expensive the copper material but also ultrasonic welding has many problem such as high error rate, difficulty of dissimilar material welding, noise, etc. At this study, the laser welding of solar panel with aluminum plate instead of copper. The welding were carried out with the pulsed Nd:YAG laser and the weld bead geometry was measured with the variation of pulse energy. Consequently, there was no difference between the ultrasonic and the laser welding on the performance of heat transfer capacities. Also the formation of intermetalic compound such as CuAl2 was increased with the pulse energy.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.1661-1667
• /
• 2008

Recently, a rolling stock has been requiring more efficient manufacturing method than welding for the improved quality and the enhanced fabrication of car body structure. As an alternative, modularization of car body structure is being studied. Accordingly, rolling stock manufacturers need to make it possible to develop a variety of rolling stock vehicles made from modularized sub-blocks in order to meet various customer's demands. The bolt-assembled car body structure for modularization is known to have many advantages over the existing weld-assembled method and is free from the possible welding defects, such as welds between dissimilar metals, crack, deformation and loss of strength. Consequently, we can have the improved overall quality, the reduced man powers for assembly and the satisfied strength of car body structure. The review is about the bolt-assembled car body structure for modularization to assure global competitiveness and an enhanced technique in terms of assembly methodology of car body structure.

• International Journal of Korean Welding Society
• /
• 제3권2호
• /
• pp.46-52
• /
• 2003

The refinement of microstructure and phase transformation near the interface of pure copper/carbon steel dissimilar metals joints with various friction welding parameters have been studied in this paper. The microstructure of copper and carbon steel joints were changed to be a finer grain compared to those of the base metals due to the frictional heat and plastic deformation. The microstructure of copper side experienced wide range of deformed region from the weld interface and divided into very fine equaxied grains and elongated grains. Especially, the microstructures near the interface on carbon steel were transformed from ferrite and pearlite dual structure to fine ferrite, grain boundary pearlite and martensite due to the welding thermal cycle and rapid cooling rate after welding. These microstructures were varied with each friction welding parameters. The recrystallization on copper side is reason for softening in copper side and martensite transformation could explain the remarkable hardening region in carbon steel side.

• 대한기계학회논문집A
• /
• 제34권1호
• /
• pp.85-90
• /
• 2010

자동차 후진기어용 축재는 단조재로서 그 형상은 복잡하고 열처리 및 가공공정이 어려울 뿐 아니라, 제품수명 저하 등의 문제점으로 인한 경제적 손실이 크다. 따라서 종전의 일체형 단조품을 캠 형상 부분만을 기존의 단조품(SF 45)으로 사용하고, 나머지 축 부분은 일반 기계구조용 탄소강재(SM 45C)로 대체를 위한 이종마찰용접을 적용하였다. 마찰용접 변수인 회전수, 마찰압력, 업셋압력, 가열시간, 업셋시간 등의 상호작용에 의한 용접품질과의 상관관계를 고찰하였으며, 최적조건에서 마찰용접을 한 후 용접재(as-welded)와 고주파 열처리를 시행한 후열처리재(PWHT)의 접합부 특성을 비교 고찰하였다. 이는 종전의 일체형 단조품에 비해 단조비용 절감, 피로수명향상, 기계가공에 따른 공정수 및 재료절감 등의 경제적 파급효과가 클 것으로 기대된다.

• Journal of Welding and Joining
• /
• 제31권2호
• /
• pp.16-20
• /
• 2013

Titanium and its alloys have been widely using in the various field of industry application due to high corrosion resistant properties and mechanical properties. Titanium is highly reactive in the high temperature state and the formation of titanium oxide and porosities in the nuggets of fusion welding will results in the degradation of the mechanical properties. For this reason the studies of friction stir welding for titanium have been investigated recently. The FSW zones of titanium were classified by the weld nugget (WN), the linear transition boundary (TB) and the heat affected zone (HAZ). The WN along with titanium parent was characterized by the presence of twins and dislocations. The average grain size and hardness of WN has been changed according to heat input. The grain refinement resulted from the FSW increased the hardness in the stir zone. Sound dissimilar joints between SUS 304 and CP-Ti were achieved using an advancing speed of 50 mm/min and rotation speeds in the range of 700-1100 rpm. Aluminum 1060 and titanium alloy Ti-6Al-4V plates were lap joined by friction stir welding, hence the ultimate tensile shear strength of joint reached 100% of Al 1060. Mg alloy and Ti were successfully butt joined by inserting a probe into the Mg alloy plate with slightly offsetting. But Ti-Al intermetallic compound layers formed at the interface of these joints.

• 대한기계학회논문집A
• /
• 제41권6호
• /
• pp.455-467
• /
• 2017

본 논문에서는 원통형 다층 이종 금속 용접부를 대상으로 유한요소 해석을 수행하여, 열원 입력 방법과 용접 비드 생성 방법이 용접 잔류 응력 분포에 미치는 영향을 고려하였다. 열원 입력 방법은 열속 입력 방법과 온도 경계조건 입력 방법으로 나누어 비교하였고, 용접 비드 생성 방법은 요소망 생성 방법과 평온 요소망 방법으로 나누어 비교하였다. 두 열원 입력 방법에 따른 열 해석 결과는 차이가 있었으나, 응력 해석 결과는 유사하였다. 이것은 고온(약 $1000^{\circ}C$ 이상)에 노출되었던 영역이 비슷하고, 고온에서 재료의 강도가 매우 낮아 용접 비드의 온도가 용접잔류응력에 미치는 영향이 미미하기 때문이다. 두 용접 비드 생성 방법의 용접 잔류응력 분포는 유사하였지만 요소망 생성 방법 적용 시 용접 비드 경계에서 겹침과 들뜸이 발생하였다. 대변형이 발생하는 모델의 용접부 형상을 정확하게 모사하기 위해서는 평온요소망이 더 적합하다고 판단된다.

• 한국해양공학회지
• /
• 제2권2호
• /
• pp.112-121
• /
• 1988

A study on friction welding of carbon steel bar (SM45C) to chrome molybedenum steel bar(SCM4) is examined experimentally through tensile test, hardness test, microstructure test and fatigue test. so, this paper deals with optimizing the welding concitions and analyzing various mechanical properties about friction welds of SM45C to SCM4 steel bars. The results obtained are summarized as follows; 1) For friction welded joints of SM45C to SCM4 steel bars, the total upset(U)increases linearly with an increase of heating time ($t_{1}$) till 6s. 2) The determined optimum welding conditions are heating time ($t_{1}$)2s, upsetting time($t_{2}$), 3s, heating pressure($p_{1}$), 4kgf/$mm^{2}$(39.2MPa), upsetting pressure($p_{2}$, 8kgf/mm$^{2}$(78.4MPa) and rotating speed(N), 2, 000rpm when the total upset(U) is 3.4mm, resulting in a computed relationship between the joint tensile strength .sigma.$_{t}$ (kgf/mm$^{2}$and the total upset U(mm); .sigma.$_{t}$ =$0.21U^{3}$ - $3.38U^{2}$ +17.03U + 66.00 3) As the elongation is increased more and more, the fracture position becomes away from weld interface and the fractures are similar to those of SM45C. Fracture is taken place on SM45C side. 4) The weld interface of two dissimilar materials is mixed strongly, and the heat affected zone is about 2.0mm at SM45C while about 2.7 mm at SCM4 side. Therefore, the welded zone and heat affected zone are very narrow, comparing with those of the joints welded by the other welding methods. 5) The fatigue strengths at N=10$^{6}$ cycles of SM45C, SCM4 and friction welded joints are 23kgf/$mm^{2}$, 33kgf/$mm^{2}$(220.5 MPa), and 22.5kgf/$mm^{2}$(220.5MPa) respectively, and fracture at friction welded joint takes place at the side of SM45C. 6) The hardness of the friction weld interface is 3 times higher than that of base metal. 7) Fatigue strength of friction welded joint is higher than that of base metal. 8) Notch sensitivity factor of friction welded joint is lower than that of base metal.

• 수산해양기술연구
• /
• 제23권2호
• /
• pp.34-34
• /
• 1987

이종재 마찰용접재 강도특성과 초음파 반사계수와의 상관성에 관하여 실험적으로 연구한 결과의 요약은 다음과 같다. 1. 이종재 마찰용접 이음면에서의 초음파 반사계수를 펄스반사법에 의하여 측정산출할 수 있다. 2. 5MHz의 비교적 낮은 주파수의 탐촉자를 사용하므로써 시험편의 표면가공 오차를 무시할 수 있다. 3. 알루미늄과 스테인레스의 마찰용접에서는 용접조건으로 마찰가열시간이나 가열압력을 변수로 하였을 때보다 업셋가압력을 변수로 하였을 때 반사계수의 변화가 뚜렷하다. 4. 업셋가압력을 변수로 한 용접조건과 반사계수사이에는 선형적 상관관계가 있다. 5. 용접이음면에서의 이음인장강도와 반사계수와의 상관관계식을 정량적으로 도출할 수 있다. 6. 초음파 반사계수에 의해 이종재 마찰용접 품질의 비파괴적 평가가 가능하다

• 수산해양기술연구
• /
• 제23권2호
• /
• pp.80-85
• /
• 1987

이종재 마찰용접재 강도특성과 초음파 반사계수와의 상관성에 관하여 실험적으로 연구한 결과의 요약은 다음과 같다. 1. 이종재 마찰용접 이음면에서의 초음파 반사계수를 펄스반사법에 의하여 측정산출할 수 있다. 2. 5MHz의 비교적 낮은 주파수의 탐촉자를 사용하므로써 시험편의 표면가공 오차를 무시할 수 있다. 3. 알루미늄과 스테인레스의 마찰용접에서는 용접조건으로 마찰가열시간이나 가열압력을 변수로 하였을 때보다 업셋가압력을 변수로 하였을 때 반사계수의 변화가 뚜렷하다. 4. 업셋가압력을 변수로 한 용접조건과 반사계수사이에는 선형적 상관관계가 있다. 5. 용접이음면에서의 이음인장강도와 반사계수와의 상관관계식을 정량적으로 도출할 수 있다. 6. 초음파 반사계수에 의해 이종재 마찰용접 품질의 비파괴적 평가가 가능하다

• 한국레이저가공학회지
• /
• 제7권2호
• /
• pp.1-10
• /
• 2004

This work was attempted to join SCP sheet and STS304 sheet by using Nd:YAC laser beam. SCP sheet has good formability and low cost, while STS304 has excellent corrosion resistance and mechanical properties in high temp. In this experiment, butt joint type was used to develop the tailored blank welding for dissimilar steel. Sheets which have different thermal properties. Computer simulation was conducted to obtain the off-set position for efficient welding by considering laser power, scanning speed, focal length and basic properties. The result showed that the optimum thermal distribution was obtained when the laser beam was irradiated at $0.05{\sim}0.1$ mm off-set toward the SCP sheet side. The experiment was conducted based on the result of computer simulation to show the same optimum conditions. Optimum conditions were 3KW in laser beam power, 6m/min in scanning speed, -0.5mm in focal position, 0.1mm off-set toward SCP. Microhardness test, tensile test, bulge test, optical microscopy, EDS, and XRD were performed to observe the microstructure around fusion zone and to evaluate the mechanical properties of optimum conditions, The weld zone had high microhardness values by the formation of the martensitic structure. Tensile test measured the strength of welded region by vertical to strain direction and the elongation of welded region by parallel to strain direction. Bulge test showed $52\%$ formability of the original materials. Bead shape, grain size, and martensitic structure were observed by the optical microscopy in the weld zone. Detailed results of EDS, XRD confirmed that the welded region was connected of martensitic structure.