• International journal of advanced smart convergence
• /
• v.6 no.4
• /
• pp.88-95
• /
• 2017

The conventional scan methods are based on a laser scanner and a depth camera, which requires high cost and complicated post-processing. Whereas in photometric scanning method, the 3D modeling data is acquired through multi-view images. This is advantageous compared to the other methods. The quality of a photometric 3D model depends on the environmental conditions or the object characteristics, but the quality is lower as compared to other methods. Therefore, various methods for improving the quality of photometric scanning are being studied. In this paper, we aim to investigate the effect of illumination conditions on the quality of photometric scanning data. To do this, 'Moai' statue is 3D printed with a size of $600(H){\times}1,000(V){\times}600(D)$. The printed object is photographed under the hard light and soft light environments. We obtained the modeling data by photometric scanning method and compared it with the ground truth of 'Moai'. The 'Point-to-Point' method used to analyseanalyze the modeling data using open source tool 'CloudCompare'. As a result of comparison, it is confirmed that the standard deviation value of the 3D model generated under the soft light is 0.090686 and the standard deviation value of the 3D model generated under the hard light is 0.039954. This proves that the higher quality 3D modeling data can be obtained in a hard light environment. The results of this paper are expected to be applied for the acquisition of high-quality data.

• Transactions on Control, Automation and Systems Engineering
• /
• v.4 no.1
• /
• pp.2-8
• /
• 2002

This paper discusses haptic display for grasping a virtual object by two fingers. Much research has been done on fundamental analysis for stability of haptic display. But it is difficult to apply the results immediately to grasping situations by two fingers, since the studies usually deal with a single device and a single object and the fingertip force in grasping situations has two components, internal and external components. The conventional methods, which specify the coupling impedance at each contact point separately, have no other alternative but to specify the impedance for the sum of the internal and external components. So even if only the impedance for the external force should be changed, the impedance for the internal force is also changed at the same time. In this paper, a new method, in which the coupling impedance is specified separately for the internal and external forces, is proposed and the stability of the proposed method is discussed using passivity analysis for 1 -DOF(Degree-Of-Freedom) system. Finally, some experiments are performed to study the effects of the proposed method.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.243-246
• /
• 2004

In this paper, we have proposed the contrast control method using brightness preserving on the FPD(Flat Panel Display). The proposed algorithms consist of three blocks: the contrast enhancement, the white-level-expander, and the black-level-expander. The proposed method has employed probability density function in order to control the brightness of the image changed extremely. In order for real-time processing, we have calculated cumulative density function using the linear approximation method. The image histogram and image quality were compared with the conventional image enhancement algorithms. The proposed methods have been used in display devices that need image enhancement such as LCD TV, PDP, and FPD.

• Communications for Statistical Applications and Methods
• /
• v.8 no.2
• /
• pp.557-564
• /
• 2001

The objective of he study is to record the real conditions along with the soccer ball that is, each player's ball keeping time, the number football keeping, accuracy of passing to other player, direction, etc., on a real-time basis, measure them in numbers and get necessary analyzed output as much as one needs. The study consists of the following stages: (1) Record the data by drawing through Visual Interface on a real-time basis; (2) Graphic windows to display the recorded data item by item in graphic; (3) Form windows to display the individual or team scores anytime when needed; (4) Windows to display the analyzed data in visualized form. The effect of the study is threefold: (1) It inputs all the game-related data on a real-time basis, which was impossible before and shows analyzed contents during the game enabling each tea manager o use; (2) In cse of TV broadcasting or newspaper articles, it explains objectively the situations of he game to the TV viewers or readers; (3) After the game, it provides importance information on each team's playing ability and individual player's technical improvement through data analysis.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.21 no.12
• /
• pp.1101-1104
• /
• 2008

We have studied electro-optic characteristics to improve viewing angle of the in-plain switching (IPS) liquid crystal display using an compensation film. The IPS mode shows relatively large light leakage and color shift in diagonal directions in a dark state. To solve this problem, we have compensated the low contrast ratio in diagonal directions using one optimized discotic film and adjusting TAC films of polarizers. The compensated IPS mode shows wide viewing angle characteristics that region of CR 50:1 is over $60^{\circ}$ of polar angle in all directions. The optimized IPS cell exhibits much better performances than other methods do in terms of CR and color uniformity.

• Journal of Information Display
• /
• v.9 no.4
• /
• pp.39-44
• /
• 2008

This paper investigates the effects of the existing sealing methods, such as the conventional atmospheric-pressure sealing method and vacuum sealing, on temporal bright-image sticking. To produce a residual image caused by temporal brightimage sticking, the entire region of a 42-in panel with an Xe-(11%)-He(35%) gas mixture was abruptly changed to a full-white background image after displaying a square-type image at peak luminance for about 60s. From the monitoring of the difference in the display luminance, infrared emission, color temperature, and disappearing time between the cells with and without temporal bright-image sticking, it was observed that the vacuum sealing method contributes to the reduction of temporal bright-image sticking.

• Proceedings of the KIEE Conference
• /
• 2005.05a
• /
• pp.239-242
• /
• 2005

A high speed address recovery technique for AC plasma display Panel(PDP) is proposed. By removing the GND switching operation, the recovery speed can be increased and switching loss due to GND switch also becomes to be reduced. The proposed method is able to perform load-adaptive operation by controlling the voltage level of energy recovery capacitor, which prevents increasing inefficient power consumption caused by circuit loss during recovery operation. Thus, the technique shows the minimum address power consumption according to various displayed images, different from Prior methods operating in fixed mode regardless of images. Test results with 50" HD single-scan PDP(resolution = 1366$\times$768) show that less than 350ns of recovery time is successfully accomplished and about 54% of the maximum power consumption can be reduced, tracing minimum power consumption curves.

• 제어로봇시스템학회:학술대회논문집
• /
• 2005.06a
• /
• pp.1673-1678
• /
• 2005

This paper addresses both theoretical and experimental studies of the stability of haptic interfaces during the simulation of virtual Coulomb friction. The first objective of this paper is to present an analysis of how friction affects stability in terms of the describing function method and the absolute stability theory. Two different feedback methods are introduced and are used to evaluate the analysis: an active force feedback, using a motor, and a passive force feedback, using controllable brake. The second objective of this paper is to present a comparison of the theoretical and experimental results. The results indicate that the sustained oscillations due to the limit cycle occur when simulating friction with an active force feedback. In contrast, a passive force feedback can simulate virtual friction without the occurrence of instability. In conclusion, a hybrid active/passive force feedback is proposed to simulate a highly realistic friction display.

• Journal of the Korean Academy of Esthetic Dentistry
• /
• v.26 no.2
• /
• pp.84-100
• /
• 2017

The causes of excessive gingival display vary, and treatment methods differ depending on the cause. Here, we will discuss how to treat gingiva and alveolar bone in the event of excessive covering of the tooth surface. This is the most common cause of gummy smile and I will systematically explain the treatment protocol and guideline based on my clinical experience.

• Journal of Information Display
• /
• v.6 no.1
• /
• pp.1-7
• /
• 2005

We propose new fabrication methods of a pixel-isolated liquid crystal (LC) structure for flexible display applications. In the LC structure fabricated through the proposed method, the patterned interpixel walls for sustaining the cell thickness are supported by the solidified polymer layer through anisotropic phase separation of LC/polymer composite, causing the alignment of the LC molecules to have very good mechanical stability against external pressure. In addition, we show that such pixel-isolating walls can be made by the stamping method which can be applied to fabricate large size plastic LCDs by roll-to-roll processing.