• Proceedings of the KSME Conference
• /
• 2001.06a
• /
• pp.669-673
• /
• 2001

The objective of this paper is to predict and evaluate the sealing performance of the thermoplastic rubber component in the proto-design stage. The large strain and large deformation properties of rubber are modeled by strain energy function and the related material constants are calculated from the test data. The viscoelastic property of the rubber is also considered using the coefficients in a Prony series representation of a viscoelastic modulus ken the compression stress relaxation test. The results show that the current design of cap mount system has 2-different stiffness caused by the cap-mount contact and the viscoelastic property of rubber plays an important role in time dependent deformation.

• Tunnel and Underground Space
• /
• v.8 no.2
• /
• pp.87-95
• /
• 1998

Field instrumentation and numerical analysis by the finite difference method were applied to estimate the relaxed zone in a subway tunnel of shallow depth in soft rock, excavated by NATM. The convergence and ground displacement can be used to estimate the deformation behavior and the relaxed zone. Parameters for the several models previously suggested were measured using regression analysis techniques adopting a function of time and the face advance. The estimated relaxed zone by the MPBX and FDM analysis were 1.5~3.0 m and 1.5~2.0 m, respectively. It was concluded that the visco-elastic model and the time-dependent elasto-plastic model correlate very well ($r^2$>0.9) with results of the numerical analyses.

• Tunnel and Underground Space
• /
• v.5 no.2
• /
• pp.95-103
• /
• 1995

In this paper the stress redistribution around tunnel face was analyzed by using a three-dimensional finite element model. The effects of in-situ stress levels, excavation sequences, stiffness difference between the hard ground and the weak zone on the stress redistributions were considered. Displacement and stress changes at tunnel crown, side wall, and invert were investigated throughout the sequential excavation. To show ground response, percentage of the displacement and stress variations are used as a function of normalized distance that is between the face and monitoring section. Preceding displacements and stress variations were presented to be adopted in the two-dimensional tunnel analysis.

• Journal of Chest Surgery
• /
• v.14 no.2
• /
• pp.168-174
• /
• 1981

Since cardiac pacemaker was first totally implanted by Chardack, Gage and Greatbatch [1966], the electrical circuity of the cardiac pacemaker has been improved, modified, and refined. The problem of transvenous electrodes, however, is still remained; this may be due to electrode displacement, exit and/or entrance block, lead fracture and insulation defects. In permanent cardiac pacing, Irreversible loss of function of the transvenous electrode catheter eventually requires insertion of new lead. Authors now report one case that disclosed easy displacement of electrode tip in early phase of implantation and then two years and five months later, malfunctioning electrode could not be withdrawn from the cardiovascular system because it has become firmly enclosed by fibrous tissue along its course from the vein tract to the right ventricle. Under such circumstances, the electrode catheter tip was left in tricuspid annulus after being sutured at its entrance and burying the loop of lead in generator pocket. New other one electrode was then reimplantation through left external jugular vein.

• Proceedings of the Korean Society of Surveying, Geodesy, Photogrammetry, and Cartography Conference
• /
• 2009.04a
• /
• pp.59-63
• /
• 2009

Structures show the phenomena of deformation and lowering of function with time-lapse by artificial environments and changes of geotechnical conditions or accumulation of initial deformation elements. This study aims the structural assessment of cultural heritage. Non-destructive evaluation techniques were applied to protect it from survey: 3D precise laser scanning surveying system was applied to measure the exact size, displacement and declining angles.

• Proceedings of the KSME Conference
• /
• 2004.04a
• /
• pp.324-329
• /
• 2004

In this study, an application of crack morphology variables in the Leak-Before-Break(LBB) evaluation for nuclear piping systems is investigated, including influences on the leakage crack size and crack instability loads. The crack surface roughness and the number of flow turns as a function of the crack opening displacement are applied to LBB evaluations for KSNP pressurizer surge line, for which fatigue and stress corrosion cracking are considered as failure mechanisms. As a result, there would be a significant impact on safety margins to acceptance criteria for the surge line if crack morphology variables are applied additionally to the current regulatory guide without re-analyses for justification of safety factors being applied on the leakage crack size and piping loads for evaluations.

• Bulletin of the Society of Naval Architects of Korea
• /
• v.19 no.4
• /
• pp.53-59
• /
• 1982

Relative bow-motions of a ship in wave are investigated by using linear theory. The relative displacement is assumed to be composed of incident wave elevation, motion response, dynamic swell-up and ship wave elevation. Radiation problem is solved by distributing sources on the hull surface and wave elevation in a uniform stream is obtained by integrating Havelock's function with centerplane source distributions. Relative displacements for I.T.T.C. S7-175 model are calculated. Dynamic swell-ups make the relative displacement larger except small heading angles. Amplitudes of relative motion on weather-side are generally larger than those on lee-side. Ship wave elevations in a uniform stream also give considerable contributions and our calculations are verified to be reasonable in comparison with experimental results.

• Structural Engineering and Mechanics
• /
• v.33 no.4
• /
• pp.391-406
• /
• 2009

Viscoelastic materials store as well as dissipate energy to the thermal domain under deformation. Two efficient modelling techniques reported in literature use coupled (thermo-mechanical) ATF (Augmenting Thermodynamic Fields) displacements and ADF (Anelastic Displacement Fields) displacements, to represent the constitutive relationship in time domain by using certain viscoelastic parameters. Viscoelastic parameters are first extracted from the storage modulus and loss factor normally reported in hand books with the help of Genetic Algorithm and then constitutive relationships are used to obtain the equations of motion of the continuum after discretizing it with finite beam elements. The equations of motion are solved to get the frequency response function and modal damping ratio. The process may be applied to study the dynamic behaviour of composite beams and rotors comprising of several viscoelastic layers. Dynamic behaviour of a composite beam, formed by concentric layers of steel and aluminium is studied as an example.

• Structural Engineering and Mechanics
• /
• v.33 no.4
• /
• pp.529-537
• /
• 2009

A key parameter in the design of a laterally loaded pile is the determination of its performance level. Performance level of a pile is usually expressed as the maximum head deflection and bending moment. In general, uncertainties in the performance of a pile originates from many factors such as inherent variability of soil properties, inadequate soil exploration programs, errors taking place in the determination of soil parameters, limited calculation models as well as uncertainties in loads. This makes it difficult for practicing engineers to decide for the reliability of laterally loaded piles both in cohesive and cohesionless soils. In this paper, limit state functions and consequent performance functions are obtained for single concrete piles to predict the maximum bending moment, a widely accepted design criterion along with the permissible pile head displacement. Analyses were made utilizing three dimensional finite element method and soil-structure-interaction (SSI) effects were accounted for.

• The Transactions of the Korean Institute of Electrical Engineers
• /
• v.43 no.5
• /
• pp.753-760
• /
• 1994

This paper proposes a new method to compute the static thrust of a hybrid-type LPM by the coenergy method, which can be applied to a nonlinear programming of the optimization techniques for the optimal design. In the process of the computation, the magnetic nonlinearities of the permanent magnet, the primary and the secondary core are interpolated by the cubic spline method. And then, the equivalent magnetic circuit including the airgap reluctance which is a function of the displacement is modelled by the permeance method. The static thrust which is a derivative of the coenergy is computed by the Newton Raphson method at each displacement. To verify this proposed method, the results of the compjutation are compaction with those of the experiment obtained from the DLPM with 2 phase and 4 poles.