In this study, a laminated composite material with dispersing aluminum oxide powder between the CFRP laminate plies, and also CFRP composites without aluminium oxide powder were fabricated for Mode I experiments using the DCB specimen and a tensile test. The behavior of the crack and the change of the interfacial fracture toughness were evaluated. Also in order to evaluate the damage mechanism for the crack extension, the AE sensor on the surface of the DCB test specimen was attached. AE amplitude was estimated for CFRP-alumina and CFRP composite. And the fracture toughness was evaluated by the stress intensity factor and energy release rate. The results showed that an unstable crack was propagated rapidly in CFRP composite specimen along with the interface, but crack propagation in CFRP-alumina specimen was relatively stable. From results, we show that aluminium oxide powder spreaded uniformly in the interface of the CFRP laminate carried out the role for preventing the sudden crack growth.
Functionalization of montmorillonite clay has been done using 3-aminopropyltriethoxy silane using water as a dispersing medium. Qualitative evidence of the presence or silane attached to the clay surface has been identified using Fourier transform infrared spectroscopy (FT-IR). Increase in silane concentration decreases the adsorbed/intercalated ratio calculated using differential thermogravimetric analysis (DTG). Average d-spacing calculated using X-ray diffraction initially increases with silane concentration and decreases slightly at higher silane concentration. The influence of processing temperature on the silane functionalization of clay has also been investigated and it shows that chemical grafting of silane on the clay surface is observed with increasing processing temperature.
International Journal of Internet, Broadcasting and Communication
/
v.16
no.3
/
pp.146-157
/
2024
Despite numerous air mattresses marketed to prevent Pressure Ulcers (PU), none have fully succeeded due to residual pressure surpassing critical levels. We introduces an innovative medical bed system aiming at complete PU prevention. This system employs a unique 4-bar link mechanism, moving keys up and down to manage body pressure. Each of the 17 keys integrates a sensor controller, reading pressure from 10 sensors. By regulating motor input, we maintain body pressure below critical levels. Keys are equipped with a servo drive and sensor controller, linked to the main controller via two CAN series. Using fuzzy or PI/IP controllers, we adjust keys to minimize total error, dispersing body pressure and ensuring comfort. In case of controller failure, keys alternate swiftly, preventing ulcer development. Through experimental tests under varied conditions, the fuzzy controller with tailored membership functions demonstrated swift performance. PI control showed rapid convergence, while IP control exhibited slower convergence and oscillations near zero error. Our specialized medical robot bed, incorporating 4-bar links and pressure sensors, underwent testing with three controllers-fuzzy, PI, and IP-showcasing their effectiveness in keeping body pressure below critical ulcer levels. Experimental results validate the proposed approach's efficacy, indicating potential for complete PU prevention.
Greater yang disease(太陽病) is a syndrome induced by peripheral obstruction. One of them is "wind stroke(中風)" with the obstruction in lymphatic system. The other obstruction appearing on circulatory system is called "cold damage(傷寒)." Kyejitang(桂枝湯) is the formula prescribed for greater yang wind stroke pattern(太陽中風證) which is caused by peripheral lymphatic duct obstruction. Ramulus Cinamoni acts as a vasodilator and Radix Paeoniae relieves the abdominal tension. They make blood move to the internal organ and this can remove the retention of peripheral lymphatic system. Covering the patient with a blanket and getting him/her to have hot and thin rice gruel causes slight Diaphoresis, contributing to relieving the retention of lymphatic system. Disharmony between nutrient and defense(營衛不和) means that pressure becomes different between lymphatic system and vascular system. Kyejitang(桂枝湯) is called releasing muscles formula(解肌劑) because it can resolve such pressure difference. Diaphoresis is not a means to eliminate pathogenic qi(邪氣) from the body. That is the syndrome proving that the body fluid has moved around when disordered fluid distribution is corrected. Therefore, diaphoresis should be induced weakly all the time. If diaphoresis is induced excessively, body fluid will move more than desired and then illness cannot be cured. In Sanghanlun(傷寒論), dispersing drugs aim at addressing the retention in the exterior field, but it actually applies to the entire exterior and interior to make body fluid move. Therefore, diaphoresis does not just act on exterior field, and freeing the stool does not only apply to interior field. Distribution of body fluid changed by pathogenic qi(邪氣) influences the whole body because the human body has a closed circulatory system. Sanghanlun(傷寒論) has included treatments for pathogenic disease. However, its value should not be limited to pathogenic disease. It is because controlling blood flow by sending body fluid to the place a doctor wants is certainly worth using for treatment of non-exogenous disease or chronic illnesses.
Proceedings of the Korea Society of Information Technology Applications Conference
/
2005.11a
/
pp.161-164
/
2005
As the power of influence of the Internet grows steadily, attacks against the Internet can cause enormous monetary damages nowadays. A worm can not only replicate itself like a virus but also propagate itself across the Internet. So it infects vulnerable hosts in the Internet and then downgrades the overall performance of the Internet or makes the Internet not to work. To response this, worm detection and prevention technologies are developed. The worm detection technologies are classified into two categories, host based detection and network based detection. Host based detection methods are a method which checks the files that worms make, a method which checks the integrity of the file systems and so on. Network based detection methods are a misuse detection method which compares traffic payloads with worm signatures and anomaly detection methods which check inbound/outbound scan rates, ICMP host/port unreachable message rates, and TCP RST packet rates. However, single detection methods like the aforementioned can't response worms' attacks effectively because worms attack the Internet in the distributed fashion. In this paper, we propose a design of distributed worm detection system to overcome the inefficiency. Existing distributed network intrusion detection systems cooperate with each other only with their own information. Unlike this, in our proposed system, a worm detection system on a network in which worms select targets and a worm detection system on a network in which worms propagate themselves cooperate with each other with the direction-aware information in terms of worm's lifecycle. The direction-aware information includes the moving direction of worms and the service port attacked by worms. In this way, we can not only reduce false positive rate of the system but also prevent worms from propagating themselves across the Internet through dispersing the confirmed worm signature.
A single write operation in a file system can modify multiple data, but these changes in the file system are not atomically written to disk. Thus, for the consistency of the file system, conventional journaling guarantees crash consistency instead of sacrificing the system performance. It is known that using non-volatile memory as a journal space can alleviate performance degradation due to low latency and byte-level accessibility of non-volatile memory. However, none of the journaling techniques considering non-volatile memory provide scalability. In this paper, journal space on non-volatile memory is divided into multiple regions for scalable journaling, thus dispersing concentrated operations in one region. Second, the journal area-specific operator structure is used to accelerate data write operations to storage devices. We apply the proposed technique to JFS to evaluate it on multi-core servers equipped with high-performance storage devices. The evaluation results show that the proposed technique performs better than the existing technique of the NVM-based journaling file system.
Lim, Young Taek;Shin, Paik-Kyun;Choi, Sun-Kyu;Lee, Sunwoo
Journal of the Korean Institute of Electrical and Electronic Material Engineers
/
v.27
no.11
/
pp.736-739
/
2014
In this paper, we propose a enhanced anti-corrosion property of the ground system by coating the CNT/PVDF composite film on it. Polymer material used for preventing the corrosion of ground system is polyvinylidene fluoride (PVDF), and conducting filler for obtaining conductivity of the composite film is multi-walled carbon nanotubes (MWCNTs). The MWCNTs were dispersed in the organic solvent of methyl ethyl ketone 2-butanone (MEK) with different concentration ratios, and the PVDF was solved in the MEK solvent with constant concentration ratio of 1 wt%. The CNT/PVDF composite solution was perpared by mixing and re-dispersing the CNT solution and the PVDF solution. Finally, the CNT/PVDF composite films were fabricated by the spray coating method using the above composite solution. Electrical conductivity, surface states, and anti-corrosion property of the CNT/PVDF composite films coated on the Cu substrate were evaluated. We found that the CNT/PVDF composite film showed relatively low resistance, hydrophobic surface state, and chemical stability. Consequently, we could improve the anti-corrosion property and maintain the electrical conductivity of the ground system by coating the CNT/PVDF composite film on it.
HA, Seung Woo;Lee, Tae Ho;Lee, Hae Seung;Kim, Jeung Min;You, Tai Woo;Cho, Sun Young
Transactions of the Korean Society of Mechanical Engineers A
/
v.40
no.7
/
pp.679-683
/
2016
Boilers of large-sized coal-fired power plants are being operated under very poor conditions such as continuous operation or repeating of start-up and shutdown for a stable supply of electricity. Thus periodic inspection and maintenance are required to ensure reliability of operation. The loads of existing scaffolding systems for the maintenance of boilers are concentrated in the lower parts structurally, which may cause a serial collapse of the overall scaffolding system when there are problems in some members. Therefore, in this study, a safe furnace scaffolding system is developed by dispersing the loads in the upper part, as well as minimizing the hazards of serial collapsing. In addition, for cases where the direct installation of furnace scaffolding is challenging owing to the structure of the boiler tube, a lifting system for the installation of furnace scaffolding is developed so that furnace scaffolding can be supported to secure the integrity of the power generating facility.
Journal of the Korean institute of surface engineering
/
v.44
no.5
/
pp.226-231
/
2011
Graphene was coated on STS 316L by electro spray coating method to improve its properties of corrosion resistance and contact resistance. Exfoliated graphite (graphene) was made of the graphite by chemical treatment. Graphene is distributed using dispersing agent, and STS 316L was coated with diffuse graphene solution by electro spray coating method. The structure of the exfoliated graphite was analyzed using XRD and the coating layer of surface was analyzed by using SEM. Analysis showed that multi-layered graphite structure was destroyed and it was transformed into fine layers graphene structure. And the result of SEM analysis on the surface and the cross section, graphene layer was uniformly formed with 3~5 ${\mu}m$ thickness on the surface of substrate. Corrosion resistance test was applied in the corrosive solution which is similar to the PEM fuel cell stack inside. And interfacial contact resistance test was measured to simulate the internal operating conditions of PEM fuel cell stack. The results of measurements show that stainless steel coated with graphene was improved in corrosion resistance and surface contact resistance than stainless steel without graphene coating layer.
SON CHOONG-YUL;JEONG UH-CHEUL;EEO JOON;CHOI JAE-KWON;LEE JUNG-TAK
Proceedings of the Korea Committee for Ocean Resources and Engineering Conference
/
2004.11a
/
pp.57-61
/
2004
According to the research result of existing regarding the seabed organic sediment, contamination it flows from the land and the sea become the enemy in the coastal water. It was caused with the summer season water temperature rise and dispersing recall respect advancement. Phosphorus which is a main reason of red tide actual condition came to reveal vast quantity with the facts that it gushes. Specially, in the case of the coastal closing waters and the nursery, as the corpse and the fresh fish washing veterinarian was imbrued, it is the actual condition where is more deepened. Consequently the development of shallow layer dredging method of that suction power which is stabilized is demanded to be able to dredge only the sediment layer which has not become the pressure and is a main reason of being imbrued. The dredging methods using the pressure difference minimize the suction of the seabed sediment. This method is stable that suction power which occurs from guard difference of the guard and the guard of the dredging system inland water. That's why it is possible to sort dredging of the organic sediment ranging in upper layer sediment and it will be able to expect the minimization of dredging quantity. Increase of the expense that it followsin orthocenter with the fact will not grow. Because the pressure difference of the dredger inland water is occurred by the suction power. Maintenance administrative costs are reduced, because the one of smallest dredging system maneuvers and the barge which affixes an integrated operation system is mainly in a resting. To reduce a dredging hour, it will be able to solve in the condensed water as operating the jar guard post.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.