• 한국세라믹학회지
• /
• 제54권2호
• /
• pp.137-140
• /
• 2017

A $TiO_2$ nanofilm was deposited on ${\alpha}-Fe_2O_3$ nanopowders using the atomic layer deposition method. The $TiO_2$ film was prepared at $300^{\circ}C$ using $Ti(N(CH_3)_2)_4$ and $H_2O$ as the precursor and reactant gas, respectively. The thickness and composition of the $TiO_2$ surface were characterized by TEM and EDS measurements. The TEM results showed that the growth rate of the film was about $0.12{\AA}/cycle$. The EDS and SAED analyses showed the presence of titanium oxide on the surface of the ${\alpha}-Fe_2O_3$ nanopowders, confirming the deposition of the $TiO_2$ nanofilm. The Zeta potential and sedimentation test results showed that the dispersibility of the coated nanopowders was higher than that of the uncoated nanopowders. This is attributed to the electrostatic repulsion between the $TiO_2$-coated layers on the surface of the ${\alpha}-Fe_2O_3$ nanopowders. The results revealed that the $TiO_2$-coated layers modified the surface characteristics of the ${\alpha}-Fe_2O_3$ nanopowders and improved their dispersibility.

• 소성∙가공
• /
• 제27권1호
• /
• pp.48-53
• /
• 2018

Aluminum nitride (AlN) is used by the semiconductor industry that has requirements for high thermal conductivity. The theoretical thermal conductivity of single crystal AlN is 320W/mK. Whereas, the values measured for polycrystalline AlN ceramics range from 20 W/mK to 280 W/mK. The variability is strongly dependent upon the purity of the starting materials and non-uniform dispersibility of the sintering additive. The conventional AlN sintering additive used yttria ($Y_2O_3$), but the dispersibility of the powder in the mixing process was important. In this study, we investigated the mechanical and thermal conductivity of yttrium nitrate ($Y(NO_3)_3{\cdot}6H_2O$), as a sintering additive in order to improve the dispersibility of $Y_2O_3$. The sintering additives content was in the range of 2 to 4.5wt.%. The density of AlN gradually increased with increasing contents of sintering additive and the flexural strength gradually increased as well. The flexural strength of the sintered body containing 4 wt% of $Y_2O_3$ and $Y(NO_3)_3{\cdot}6H_2O$ was 334.1 MPa and 378.2 MPa, respectively. The thermal conductivities were 189.7W/mK and 209.4W/mK, respectively. In the case of hardness, there was only a slight difference and the average value was about 10 GPa. Therefore, densification, density and strength values were found to be proportional to its content. It was confirmed that AlN using $Y(NO_3)_3{\cdot}6H_2O$ displayed relatively higher thermal conductivity and mechanical properties than the $Y_2O_3$.

• Korean Chemical Engineering Research
• /
• 제51권5호
• /
• pp.628-633
• /
• 2013

토너 입자 내부의 카본블랙의 분산성이 우수한 스타이렌 기반 현탁중합토너를 제조하기 위하여 카본블랙의 표면을 개질하였다. 산화반응을 통해 카본블랙 표면에 도입된 히드록시기와 유기산(올레산, 팔미트산, 아크릴산)의 카르복시기 사이의 에스터화 반응을 통해 표면이 유기화 개질된 카본블랙을 제조하였다. 카본블랙의 표면개질을 확인하기 위하여 FTIR을 이용하였다. 바인더 수지 모노머 혼합물에 대한 카본블랙의 가시적인 분산성 실험을 진행하였으며 입도분석기를 이용해 분산된 카본블랙의 입자 크기를 측정하였다. 광학현미경 사진을 분석한 결과 표면이 올레산으로 개질된 카본블랙을 사용할 경우 토너 입자 내부의 카본블랙의 분산성이 크게 향상되었다. 올레산으로 개질된 카본블랙을 이용해 제조한 중합토너는 입경 및 입경분포도 토너로서 이상적이었다.

• 펄프종이기술
• /
• 제42권5호
• /
• pp.74-82
• /
• 2010

Curtain stability without curtain contraction is critical for a successful operation in curtain coating, and this can be influenced by the change in particle dynamics and rheological properties of coating colors. In this study, polyvinyl alcohol (PVA) and carboxymethyl cellulose (CMC) were added to control the rheology of GCC based curtain coating colors. Surface tension was increased slightly with increasing content of cobinder. Shear-thinning of viscosity was more pronounced for the CMC containing GCC coating colors. Complex modulus decreased when small amount of PVA was used as a cobinder, but it increased in other coating colors. Extensional viscosity was increased with increasing of the cobinder content, but CMC was more effective. Results indicate that pigment interaction with PVA is different from that with CMC. Dispersibility of coating colors was improved due to steric stabilization when small amounts of PVA was used, but flocculation occurred by bridging when the amount of PVA was increased. Dispersibility of coating colors was improved when small amount of CMC was added, while flocculation was observed by depletion effect when the concentration of CMC was increased in coating colors. Addition of cobinders at proper levels gave positive effects both in rheological properties and curtain stability. On the other hand, excessive amount of cobinders caused particle flocculation and this resulted in rheological and curtain stablity problems.

• 폴리머
• /
• 제35권6호
• /
• pp.543-547
• /
• 2011

전도성고분자 polyaniline(PANI)의 구조 변화없이 전기전도도를 띠면서 가공성과 기계적 특성을 증가시키는 연구를 수행하였다. 기능성 산으로 도핑된 PANI-DBSA는 유화 중합하였고, dodecylbenzenesulfonic acid(DBSA)는 계면활성제와 도펀트 역할을 동시에 하도록 하였다. 이어서 PANI-DBSA를 high impact polystyrene(HIPS)와 용액 캐스팅하여 블렌드 필름을 제조하였다. UV-vis, FTIR/ATR 분광법으로 블렌드 구조와 전기적 특성을 확인하였다. PANI-DBSA/HIPS 블렌드에 관한 연구는 분산성과 모폴로지 변화에 따른 기계적인 특성과 전기적 특성 확인에 중점을 두고 진행하였다. 전기전도도는 PANI-DBSA 함량 증가에 따라 상승하였고, 9 wt% 정도로 낮은 함량에서도 $3.5{\times}10^{-4}$ S/cm로 급격하게 상승하였다. 전도성고분자 블렌드에서 연속적인 고분자 망상구조 형성이 percolation과 전기전도도에 밀접한 연관성이 있었다.

• Composites Research
• /
• 제35권1호
• /
• pp.18-22
• /
• 2022

복합재료의 제조에 있어서 분산은 매우 중요한 요소 중 하나이다. 복합재료의 제조 시 matrix 용재에 강화재를 보다 잘 분산하기 위하여 용매를 사용하는데 용매에 따라 분산도가 달라지기 때문에 어떠한 용매가 분산에 용이할지에 대한 연구가 필요하다. 본 연구에서는 다양한 솔벤트 용매(DMF, NMP, Ethylene glycol, Acetone, DI water)에 대해 나노 필러인 산화 그래핀(Graphene oxide)의 용매에 따른 GO의 분산거동과 용해도 분석을 통해 분산에 유리한 용매를 파악하고자 하였다. 그 결과 UV-Vis spectroscopy 흡광도 측정을 통해 DMF와 Ethylene glycol이 가장 좋은 분산성을 가짐을 알 수 있는 반면 DI water는 가장 낮은 분산성을 보임을 알 수 있었다. 또한 표면장력과 시간에 따른 분산 육안 관측을 통해 DI water, Ethylene glycol, NMP, DMF, Acetone 순으로 분산성이 우수한 것을 알 수 있었는데 이는 Hansen solubility parameter 값과 일치하는 경향임을 확인할 수 있었다.

• International Journal of Concrete Structures and Materials
• /
• 제9권2호
• /
• pp.207-217
• /
• 2015

The influence of powdered and colloidal nano-silica (NS) on the mechanical properties of cement mortar has been investigated. Powdered-NS (~40 nm) was synthesized by employing the sol-gel method and compared with commercially available colloidal NS (~20 nm). SEM and XRD studies revealed that the powdered-NS is non-agglomerated and amorphous, while colloidal-NS is agglomerated in nature. Further, these nanoparticles were incorporated into cement mortar for evaluating compressive strength, gel/space ratio, portlandite quantification, C-S-H quantification and chloride diffusion. Approximately, 27 and 37 % enhancement in compressive strength was observed using colloidal and powdered-NS, respectively, whereas the same was up to 19 % only when silica fume was used. Gel/space ratio was also determined on the basis of degree of hydration of cement mortar and it increases linearly with the compressive strength. Furthermore, DTG results revealed that lime consumption capacity of powdered-NS is significantly higher than colloidal-NS, which results in the formation of additional calcium-silicate-hydrate (C-S-H). Chloride penetration studies revealed that the powdered-NS significantly reduces the ingress of chloride ion as the microstructure is considerably improved by incorporating into cement mortar.

• Preventive Nutrition and Food Science
• /
• 제15권1호
• /
• pp.67-73
• /
• 2010

The effects of particle sizes (small, medium and large sizes) and gelatinization treatment on the changes of the instant properties of Job's tears powder were investigated. The degree of gelatinization on the different particle size samples of Job's tears powder was the highest in the small particle size, and it also showed an increasing trend regardless of pregelatinizing whether it is or not as the particle size decreased from large particle size to small particle size. The water solubility index of the pregelatinized samples was high compared to that of ungelatinized samples regardless of particle size and temperatures. The water absorption and swelling power increased as particle size and temperature were increased. The dispersibility and sinkability of ungelatinized sample was increased as particle size and temperature were increased and it also showed lower value regardless of particle size and temperature. However, the dispersibility and sinkability of pregelatinized samples were shown to have the opposite result, such that the smallest particle size of pregelatinized sample had the lowest sinkability (11.3%). The turbidity of the pregelatinized small particle size was the highest by a factor of 1.08.

• 환경위생공학
• /
• 제13권3호
• /
• pp.58-65
• /
• 1998

Monodispersed $SiO_2/ZnO$ composite fine powders were prepared by Sol-Gel processing and their surface electrical and UV absorbance properties were investigated. Pseudomorph ZnO fine powders were microcapsuled by $SiO_2/ZnO$ sol fabricated using TEOS[tetraethylorthosilicate, purity 98% and ethanol as a solvent with $NH_3$ catalyst. The effects of experimental parameters such as molar ratio of starting materials on the final particle size and shape of $SiO_2/ZnO$ composite fine powder were discussed. As a result, we could controlled the size of monodispersed $SiO_2/ZnO$ composite fine powders without agglomeration, as well as the good dispersibility in aquous solution. The prepared powders were observed to have the mean particle sizes of $0.26-0.78{\mu}m$ with standard deviations of $0.020-0.063{\mu}m$.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2007년도 춘계학술논문 발표대회
• /
• pp.51-54
• /
• 2007

This study investigates the properties of paste and mortar from different types and forms of silica fume on cement binder for ultra high strength. Although most Silica Fumes distributed in the market fulfill the KS quality standard, each type showed different levels of loss of ignition. When evaluating cement binder for ultra high strength in a form of paste. Flow, viscosity and moving freely time show great difference depending on the Silica Fume's form and type of primary particle's dispersibility. The evaluation of Silica Fume's dispersibility can be possible with the paste test since there is a high correlation of flow quality between paste and mortar. The compressive strength when using Silica Fume was correlated to the SiO2 content. Synthetically, selecting Silica Fume with the most the ideal primary particle is the key to optimizing the formation for cement binder for ultra high strength.