• 상하수도학회지
• /
• 제33권5호
• /
• pp.395-404
• /
• 2019

The point-of-use water dispenser systems are widely used because of convenience in handling and demand for high-quality drinking water. The application has been increased recently in the public places such as department stores, universities and the rest areas in express ways. Improvement of water qualities by the dispenser systems was compared with tap water in this study. The tap water is supplied to the dispenser as the influent of the dispenser system. The twelve dispensers in the public places were used. The five dispensers used reverse osmosis as the main filter and other dispensers used various filters such as ultrafiltration, nanofiltration, and alumina filter. The water quality indicators for sanitation safety, i.e., turbidity and total coliforms, were evaluated. Other water qualities such as pH, residual chlorine, heterotrophic plate count (HPC), and total cell counts were also analyzed. By the point-of-use water dispenser, the turbidity, residual chlorine and pH were decreased and the HPC and total cell counts were increased. The t-test results revealed that the HPC of the tap waters were not significantly different from the treated waters but the total cell counts of the two groups were significantly different. The low pH of the RO filter treatment was also significantly different from the tap waters. This study will contribute to understand the role of the point-of-use water dispenser in improving water quality and to identify key water quality for the proper maintenance of the dispenser systems.

• 제어로봇시스템학회논문지
• /
• 제6권6호
• /
• pp.506-513
• /
• 2000

This paper proposes a path planning algorithm for dispensers to increase the productivity in printed circuit board assembly lines. We analyze the assembly sequence of the dispenser, and formulate it as an integer programming problem. The mathematical formulation can accomodate multiple heads and different types of heads through extended cost matrix. The TSP algorithms are then applied to the formulated problem to find the near-optimal solution. Simulation results are presented to verify the usefulness of the proposed scheme.

• 한국소음진동공학회논문집
• /
• 제26권5호
• /
• pp.546-551
• /
• 2016

The objective of this study is to investigate the response delays between piezo-stack actuator and the displacement magnifier of jetting dispenser and to reduce its falling time in terms of displacement optimization. The dispenser is driven by the dual piezo-stack actuators with a hinge lever mechanism to precisely control flow rate of the working fluid (3000 cP). It is commonly found that piezo actuator-driven jetting dispensers involving viscous working fluids have displacement optimization problem for ideal performance. The response delay of the system is caused by the phenomenon that the displacement magnifier cannot exactly follow the motion of the piezo actuators. The response delay may lower the performance of the system due to the inaccurate discharge of working fluid or even damages to the system itself due to inharmonious motion of piezo actuators with lever system. To reduce its response delay, a new displacement profile obtained from displacement optimization is suggested; its performance is tested through finite element analysis; and experiments are carried out to verify the performance of the obtained displacement profile.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2007년도 추계학술대회논문집
• /
• pp.595-600
• /
• 2007

This paper presents a new jetting dispenser driven by a piezoelectric actuator at high operating frequency to provide very small dispensing dot size of adhesive in modern semiconductor packaging processes. After describing the mechanism and operational principle of the dispenser, a mathematical model of the structured system is derived by considering behavior of each component such as piezostack and dispensing needle. In the fluid modeling, a lumped parameter method is applied to model the adhesive whose rheological property is expressed by Bingham model. The governing equations are then derived by integrating the structural model with the fluid model. Based on the proposed model, dispensing performances such as dispensing amount are investigated with respect to various input trajectories.

• 한국소음진동공학회논문집
• /
• 제18권4호
• /
• pp.432-438
• /
• 2008

This paper presents a new jetting dispenser driven by a piezoelectric actuator at high operating frequency to provide very small dispensing dot size of adhesive in modern semiconductor packaging processes. After describing the mechanism and operational principle of the dispenser, a mathematical model of the structured system is derived by considering behavior of each component such as piezostack and dispensing needle. In the fluid modeling, a lumped parameter method is applied to model the adhesive whose rheological property is expressed by Bingham model. The governing equations are then derived by integrating the structural model with the fluid model. Based on the proposed model, dispensing performances such as dispensing amount are investigated with respect to various input trajectories.

• 한국소음진동공학회논문집
• /
• 제16권11호
• /
• pp.1165-1171
• /
• 2006

This paper presents a new type of jetting dispenser for the integrated circuit (IC) fabrication and surface mount technology The proposed system is featured by the piezoelectric actuator and hydraulic magnification device. After describing structural component of the dispensing mechanism and its operation principle, both the fluid modeling and the hydraulic magnification modeling are undertaken with a lumped-parameter method based on the analogy of the fluid system and mechanical system. A mathematical governing equation is then derived by integrating the fluid model with the mechanical model of the driving piston and piezoelectric actuator. Subsequently, in order to achieve a desired dispensing amount, control algorithm adjusting duty cycle of the driving voltage is synthesized and control responses are presented in time domain.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.428-433
• /
• 2006

This paper presents a new type of jetting dispenser for the integrated circuit(IC) fabrication and surface mount technology. The proposed system is featured by the piezoelectric actuator and hydraulic magnification device. After describing structural component of the dispensing mechanism and its operation principle, both the fluid modeling and the hydraulic magnification modeling are undertaken with a lumped-parameter method based on the analogy of the fluid system and mechanical system. A mathematical governing equation is then derived by integrating the fluid model with the mechanical model of the driving piston and piezoelectric actuator. Subsequently, in order to achieve a desired dispensing amount, control algorithm adjusting duty cycle of the driving voltage is synthesized and control responses are presented in time domain.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.341-342
• /
• 2012

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1997년도 하계학술대회 논문집 C
• /
• pp.1566-1569
• /
• 1997

In this paper, we developed newer cooling system which has better efficiency and make smaller pollution than older cooling system compressor type by using TEC Module. And then we investigated application of Peltier Effect cooling technology applied to the cold water dispenser.

• 한국콘텐츠학회:학술대회논문집
• /
• 한국콘텐츠학회 2006년도 춘계 종합학술대회 논문집
• /
• pp.462-465
• /
• 2006

근년에 들어 신용거래 문화가 확산되는 한편 고객에 대한 한 차원 높은 서비스를 제공하며 업무의 효율성 재고라는 의미에서 은행 업무의 자동화는 더욱 빠르게 진행되고 있다. 예컨대 고객에 대한 현금 지불 처리의 자동화는 현재 계속 진행되어 업체간 경쟁이 심해지고 있는 것이 현실이다. 최근 들어 본격 은행자동화기기(BANKING AUTOMATION SYSTEM)화를 추구하는 각 은행들은 보다 더 원활한 전산업무화와 질적으로 높은 고객서비스를 위해 현금자동인출기(CASH DISPENSER) 보급을 확대하고 있다. 따라서 현금자동인출기를 제작하는 MAKER들도 선두주자로서의 M/S 확보를 위해 다각도로 현금자동인출기 개발에 박차를 가하고 있다. 현금인출 자동화 기기인 CASH DISPENSER는 이제 일반화되어 기능의 다양화와 DESIGN이 COMPACT화해 가는 추세이다. 이러한 현 상황 하에서 실제로 현금자동인출기(CASH DISPENSER)를 개발을 하였던 과정을 근거로 하여 보다 더 신뢰성 있고 편리하게 사용할 수 있는 현금자동인출기(CASH DISPENSER)제안을 사례 형식으로 살펴 보고 앞으로의 DESIGN 개발 방향을 제시해 보았다.