• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2000년도 추계학술대회논문집
• /
• pp.742-747
• /
• 2000

The optical storage device has recently experienced significant improvements, especially for the aspects of high capacity and fast transfer rate. However, it is the fact that the optical storage device has the lower access time for the randomly scattered data compared to the hard disk drives. It is, therefore, necessary to develop a new type of optical storage system. In this study, we investigate the air bearing characteristics for the optical disk drives which have the swing arm actuator similarly to the hard disk drives. Considering the requirements of the optical disk drives, we parametrize the shape of the air bearing surface and investigate its sensitivity to the flying characteristics for further optimized design outputs.

• 한국융합학회논문지
• /
• 제11권6호
• /
• pp.209-213
• /
• 2020

본 연구에서는 경주용 자동차에서 기존에 사용 중인 형상을 가진 모델 A와 경량화를 한 모델 B를 설계하고 열 변형과 열응력을 동반한 구조해석을 하였다. Model A가 Model B에 비하여 최고온도가 낮음을 보인다. 다른 냉각 조건이 주어지지 않고 디스크의 형상에 따른 냉각성능은 Model A가 더 뛰어남을 알 수 있다. Model A가 Model B에 비하여 거의 2배 이상으로 그 열응력이 낮아져 내구성면에서도 우수함을 알 수 있었다. 응력이 가장 크게 나타나는 부분은 형상에 관계없이 허브와 접합되는 구멍으로 나타났다. 본 연구에서의 해석결과는 실제 자동차 브레이크 디스크의 형상을 설계하는데 있어서 유용하다고 보인다. 본 연구에서 얻은 해석 결과는 실제적으로 경주용 자동차 브레이크 디스크의 강도를 파악하는 데에 적용될 수 있다. 경주용 자동차 브레이크 디스크의 해석 결과를 이용함으로서, 본 연구가 미적인 설계 및 해석이 적용된 융합 연구라고 보여진다.

• 한국기계가공학회지
• /
• 제12권4호
• /
• pp.100-107
• /
• 2013

This study aims to improve the heat performance of motor cycle disk due to the number of holes by analyzing 6 kinds of disk models. This disk performance depends on the efficiency at emitting the heat. To raise the efficiency of heat emission, holes with circle or another configuration are made on disks to emit heat fast. The distribution of temperature, heat flux, deformation and stress are analyzed. As the number of holes on disk increases, the performance of heat emission is improved. Equivalent stress is decreased and durability is improved as the number of holes on disk increases. Though the number of holes on disk is increased, the performances of heat emission and durability do not become better. The optimal model can be found by comparing models each other through this analysis result. Through this study result, the configuration of motor cycle disk is designed with optimal heat emission and durability by comparing models.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.539-542
• /
• 2002

The role of disk clamp is to fasten disks to motor and to prevent the slip of disks during operation. This paper examined the effects of the design parameters of disk clamp - thickness, contact radius and cross-sectional shape -on the clamping force and circumferential stress distribution of disk. The large stress variation in circumferential direction results in large disk waveness and will increase repeatable run-out (RRO) finally. The disk clamp-disk-disk spacer system is modeled and the FE analysis is performed by ANSYS. The disk clamp with large contact radius shows more uniform stress distribution than the one with small contact radius and the stiffness variation around circumferential direct ion or the addition of the bending sect ion can make stress distribution uniform.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2006년도 춘계학술대회 논문집
• /
• pp.235-236
• /
• 2006

The disk cam mechanism can produce a positive motion with relatively few components. This paper introduce a shape design of cam using the relative velocity method and a precision machining technology for using Bi-arc method. The paper gives a machining information at each point using the Bi-arc method and the analysis method of the cutting error due to the moving path of the cutter, so that we can lead to the optimum design in a disk cam mechanism.

• 대한전기학회논문지
• /
• 제36권11호
• /
• pp.806-812
• /
• 1987

The ozone generation characteristics are reported for a sawtooth disk to cylinger geometry using positive and negative pulse corona. A series of parametric studies was carried out to obtain optimum values for the pulse repetition frequency as well as the shape and dimensions of the discharge disk and the discharge spacing. Two types of ozonizers were studied: the single disk and the multi-disk. The results of the single disk ozonizer showed that positive corona produced a singificantly higher ozone yield than negative(7ppm/peak watt or 3.5 times larger). However the negative corona produced a much more controllable output which enabled the ozone generation to be directly controlled by adjusting the value of the peak pulse voltage. This results showed that the single disk ozonizer is ideally suited for applications requiring very small controlled quantities of ozone whereas the multi-disk unit can be designed to provide varying outputs depending upon the number of disk electrodes used.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2002년도 춘계학술대회논문집
• /
• pp.533-538
• /
• 2002

This research demonstrates the transient response of a head disk assembly subjected to a half-sine shock pulse in the axial direction. In case of disk analysis, the numerical method presented by Barasch and Chen is used. Galerkin method is used with mode shape by numerical method. head-suspension system is modeled by the cantilever in order to get simulation results. Simulation results about total system of HDA are calculated by Runge-Kutta method.

• 한국전자파학회:학술대회논문집
• /
• 한국전자파학회 2001년도 종합학술발표회 논문집 Vol.11 No.1
• /
• pp.119-122
• /
• 2001

In this paper, an elliptic disk-loaded antenna having frequency shift characteristics with the same height of the simple monopole is studied. The proposed antenna is composed of an ellitptic disk with arbitrary ellipticity ratio. The eigenmode representations in each region of given structure are useful for the analysis of the canonical monopoly, circular disk-loaded monopole and circular dielectric-loaded top-hat monopole antennas using the artificical ground plane. The comparison between the elliptic and circular disk-leaded antenna is carried out. The effect of the shape of the loaded disk and the ellipticity ratio of the loaded disk on the input impedances, the return loss and frequency shift is also studied. We have computed the given structures using the CST MW Studio version 3.0. The typical blade antenna can be obtained by modifying and extending the proposed structure with the λ/4 balun removing the stray capacitances existing between the loaded disk and the ground plane.

• 정보저장시스템학회논문집
• /
• 제3권2호
• /
• pp.81-85
• /
• 2007

Reliability of a hard disk drive depends on the head disk interface (HDI) characteristics. Particularly, the disk media and the head can be damaged due to contact between the two components during operation. The contact may occur due to particles being introduced into the disk/slider interface or due to direct contact between the slider and the disk. Such contacts may be induced by external vibration or abnormal operation of the HDI. In this work the characteristics of scratches generated on the disk surface were investigated. The scratches were generated by impacting the hard disk. The type of scratches was analyzed with respect to their shape and dimensions.

• Journal of Astronomy and Space Sciences
• /
• 제38권1호
• /
• pp.39-44
• /
• 2021

In the general accretion disk model theory, the accretion disk surrounding an astronomical object comprises fluid rings obeying Keplerian motion. However, we should consider relativistic and rotational effects as we close in toward the center of accretion disk surrounding spinning compact massive objects such as a black hole or a neutron star. In this study, we explore the geometry of the inner portion of the accretion disk in the context of Mukhopadhyay's pseudo-Newtonian potential approximation for the full general relativity theory. We found that the shape of the accretion disk "puffs up" or becomes thicker and the luminosity of the disk could exceed the Eddington luminosity near the surface of the compact spinning black hole.