• Tribology and Lubricants
• /
• 제23권4호
• /
• pp.175-179
• /
• 2007

The effect of manufacturing parameters on friction characteristics of motorcycle break system was studied using a design of experiment. Such parameters conditions have an effect on the frictional factor such as applied load, sliding speed, and number of ventilated disk hole. However, it is difficult to know the mutual relation of these factors. In this study, the friction characteristics using design of experiment containing 3 elements were investigated for an optimal condition for the best motorcycle break system employing full factorial design. From this study, the result was shown that the applied load in frictional factors was the most important, next to sliding speed, number of ventilated disk hole.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2004년도 춘계학술대회
• /
• pp.519-524
• /
• 2004

This study is concerned with the braking distance estimation using frictional energy rate. First, steady state rolling analysis is performed, and using this result, the braking distance is estimated. Dynamic rolling analysis during entire braking time period is impratical, so that this study divides the vehicle velocity by 10km/h to reduce the analysis time. The multiplication of the slip rate and the shear stress provides the frictional energy rate. Using frictional energy rate, total braking distance is estimated, In addition, ABS(Anti-lock Brake System) is considered, and two type of slip ratios are compared, One is 15% slip ratio for the ABS condition, and the other is 100% slip ratio which leads lo the almost same braking distance as the elementary kinematic theory. A slip ratio is controlled by angular velocity in ABAQUS/Explicit, A 15% slip ratio gives the real vehicle's braking distance when the frictional energy occurred al disk pad is included. Disk pad's frictional energy rate is calculated by the theoretical approach.

• Tribology and Lubricants
• /
• 제13권1호
• /
• pp.34-41
• /
• 1997

Frictional behavior of three automotive friction materials (brake pads) containing different amounts of antimony trisulfide ($Sb_2S_3$) and zirconium silicate ($ZRSiO_4$) were investigated using a front brake system. The friction materials were tested on a brake dynamometer (dyno) with gray cast iron rotors. The dynamometer(dyno) test simulated the dragging of a ehicle maintaining 70 km/h and vehicle stops from 100 km/h using 20 different combinations of initial brake temperature (IBT) and input pressure (IP). The results showed a strong influence of the relative amount of $Sb_2S_3$ and $ZrSiO_4$ in friction materials on friction characteristics. Friction stability was improved with the higher concentration of $Sb_2S_3$ in the friction material. Torque variation during drag cycle was increased with an increase of the $ZrSiO_4$ concentration in the friction material. Average friction coefficient and the wear rate of the friction material increased by using more aggressive friction materials containing more $ZrSiO_4$ and less $Sb_2S_3$. Generation of the disk thickness variation (DTV) increased when friction materials with higher concentration of $ZrSiO_4$ were used Careful examination of DTV change showed that aggressiveness of the friction material played an important role in determining torque variation.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2004년도 추계학술대회 논문집
• /
• pp.405-410
• /
• 2004

There are two types of noises in running the rail vehicle. The one is periodic by electric motors, dehumidifiers, and dusting machines. And the other is aperiodic squeal noise by the frictions between the wheels and the rail or the disks and pads. The periodic noises in rail vehicle have been reduced by changing DC motors to AC motors with silencers, and by improving the lubricants. However, almost nothing relating a periodic noise has been studied. In this paper, the experimental methods were applied to understand phenomena of the squeal noise, which was occurred by the friction variation due to aperiodic stick and slip with low repeatability in the process of dry friction of the disk and the pad when a rail vehicle was being braked. By the experimental acoustic test, it was found the specific frequencies relating the squeal noise. And by modal testing, it was measured the resonant frequencies in the disk and the pad-plate which were the components of the braking system, and in the whole braking system, and it was found the specific frequencies having the effects on the squeal noise.

• Tribology and Lubricants
• /
• 제9권1호
• /
• pp.62-69
• /
• 1993

Friction and wear behavior of a carbon/carbon composite material for aircraft brake material was experimentally investigated. Friction and wear test setup was designed and built for the experiment. Friction and wear tests were conducted under various sliding conditions. Friction coefficients were measured and processed by a data acquisition system and amount of wear measured by a balance. Stainless steel disk was used as the counterface material. Temperature was also measured by inserting thermocouple 2.5 mm beneath the sliding surface of the carbon/carbon composite specimen. Wear surfaces were observed by SEM, and analyzed by EDAX. The experimental results showed that sliding speed and normal force did not have significant effects on friction coefficient and wear factor of the composite. Temperature increase just below the surface was not large enough to cause any thermal degradation or oxidation which occurred at higher temperature when tested by TGA. Wear film was generated both on the specimen and on the counterface at relatively low sliding speed but cracks, grooves, and wear debris were observed at high sliding speed. Friction coefficient remained almost constant when the sliding speed or normal load was varied. It is believed that the adhesive and abrasive components contributed mainly to the friction coefficient. Wear behavior at low sliding speed was governed by wear film formation and adhesive wear mechanism. At high speed, fiber orientation, ploughing by counterface asperities, and fiber breakage dominated wear of the carbon/carbon composite.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2007년도 춘계학술대회 논문집
• /
• pp.786-791
• /
• 2007

고속철도차량의 제동시스템은 전기제동장치, 디스크제동장치, 답면제동장치 등 다양한 제동장치들의 조합으로 구성되며 요구되는 제동성능을 충족하는 범위 내에서 에너지의 효율적인 활용과 마찰재의 경제성을 고려하여 각 제동장치에 대한 제동블랜딩 제어 기능을 포함하고 있다. 일반적으로 요구제동거리를 만족하기 위한 열차 전체에 대한 제동력 패턴을 설정하고 전기제동을 최우선적으로 투입하고 부족한 부분에 대하여 기계제동을 사용하여 부족한 부분을 보상하는 방법을 사용하고 있다. 기계제동장치의 대부분을 차지하고 있는 디스크제동장치는 디스크와 패드 사이의 마찰력을 이용하여 제동력을 확보하는 것으로 사용에 따른 마모가 발생한다. 특히, 고속영역에서 사용하는 경우 패드 마모량은 저속에 비하여 급격히 증가하게 되어 패드의 교환 주기를 단축시킬 뿐만 아니라 제동 초기 과정에서 온도의 상승으로 인한 제동효율의 저하를 가져오는 단점이 있다. 따라서, 본 논문에서는 제동거리, 감속도, 감속도 변화율 등 요구되는 제동성능을 만족시키는 범위 내에서 디스크 제동장치의 패드 마모량 감소를 위한 열차 주행속도에 따른 디스크 제동력 패턴을 설정하는 하나의 방법론으로 제시된 제동초기에서부터 정지할 때까지의 디스크제동에너지의 분산을 최소로 하는 최적화 방법을 이용하여 한국형 고속열차를 바탕으로 제작되는 10량 편성의 고속열차를 대상으로 모든 제동장치가 정상인 경우와 1개의 전기제동장치가 고장이 발생한 경우에 대한 패드 마모량을 구하고 현재 설정된 디스크 제동력 패턴에서의 패드 마모량과의 비교 검토를 수행하였다.經章句索引)${\lrcorner}$이분위오절진행료연구(而分爲五節進行了硏究). 본편기재료상견적흔다잡병, 재임상상유흔대적연구가치. 단시통과역대다차전초(但是通過歷代多次轉抄), 유흔다오식, 착간(錯簡), 가차적부분(假借的部分), 인차유흔다불역리해적지방. 여과불참조다종판본화역대주석가적연구성과(如果不參照多種版本和歷代註釋家的硏究成果), 취무법진정영회기본의(就無法眞正領會其本意). 기어저일점(寄於這一點), 본편논문연구료역대판본화주석가적견해(本篇論文硏究了歷代版本和註釋家的見解), 병진행료교감화교주(幷進行了校勘和校註), 재가어료현토급국어주석(再加於了懸吐及國語注釋), 이기갱유조어정확지리해원문적본의(以期更有助於正確地理解原文的本意). 보고하는 바이다. 관련된 부작용(ADR)이 발생하지 않았다. 따라서 UDB는 본 임상연구 기준에서 포함하는 모든 병력의 만성 간질환에서 ALT 수치가 지속적으로 상승해 있는 경우 효과적이고도 안전하게 투여할 수 있는 제제로 생각된다. pH는 4.4이었으며 최적온도(最適溫度)는 $30^{\circ}C$이었다. 3. CHS-3 균주(菌株)의 specific growth rate는 $0.23\;h^{-1}$, generation time 은 3.01h이었다. 4. CHS -13균주(菌株)의 기질소비율(基質消費率)은 81%이었다. 5. CHS-13 균주(菌株)의 형태학적(形態學的) 배양학적(培養學的) 특성(特性)을 조사(調査)한 결과(結果) Candida guilliermondii var. guilliermondii 로

• 한국기계가공학회지
• /
• 제13권6호
• /
• pp.61-65
• /
• 2014

Construction heat insulating material for construction is used in large amounts in industry. In the manufacturing process of this insulation material, a thermal insulation material is completed while a polymer in a liquid state passes through Hall breaker. At this time, the quality and form of a product are determined by a hole in the breaker according to the oil pressure of the fluid and the change of the flow velocity. The friction wear action with regard to partner movement between the two levels of quality of materials affects the performance and the lifetimes of machine parts. In this study of a friction test, SM45C, which is a material used to create brake holes, was used. PVC was used to create the specimen. Moreover, an experiment divided a lubricous state and an unlubricated condition. The resulting value over the load of a pin, the revolving speed of a disk, and the standby state of an experimental result disk could be acquired.

• 한국소음진동공학회논문집
• /
• 제24권5호
• /
• pp.363-373
• /
• 2014

In this study, computational multi-body dynamic analyses for the drivetrain system of a 5 MW class offshore wind turbine have been conducted using efficient equivalent modeling technique based on the design guideline of GL 2010. The present drivetrain system is originally modeled and its related system data is adopted from the NREL 5 MW wind turbine model. Efficient computational method for the drivetrain system dynamics is proposed based on an international guideline for the certification of wind turbine. Structural dynamic behaviors of drivetrain system with blade, hub, shaft, gearbox, supports, brake disk, coupling, and electric generator have been analyzed and the results for natural frequency and equivalent torsional stiffness of the drivetrain system are presented in detail. It is finally shown that the present multi-body dynamic analysis method gives good agreement with the previous results of the 5 MW class wind turbine system.

• 한국초전도ㆍ저온공학회논문지
• /
• 제2권2호
• /
• pp.44-48
• /
• 2000

The high temperature superconducting bulk can be used as the rotor of an ac motor. This paper presents the fabrication and test results of a ac motor with HTS bulk rotor. The rotor of a conventional squirrel cage induction motor was replaced with cylinder type YBCO bulk. Height and outer diameter of the HTS bulk was 15mm and 46mm, respectively. Eddy current brake using aluminium disk was used to measure the torque of the HTS motor. No load test, locked rotor test and load test were performed to examine the characteristics of the HTS motor. Test results show the motor can rotate at synchronous speed without any special starting circuit. Maximum output power of the constructed HTS motor was 408W.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2009년도 춘계학술대회 논문집
• /
• pp.1643-1648
• /
• 2009

The braking system of train must posses the large baking effort in order to stop the train safety within the limited traveling distance. but, the excessive braking effort has been deteriorated the ride comfort due to high level of deceleration and jerk, and sometimes occurred the skid. because the applied braking force exceeds the allowable adhesive force. this skid causes not only to increase the a stopping distance but also to deteriorate the safety of train and damage the rall surface by wheel flat. In the present paper, braking force for disk brake of Tilting Train eXpress(TTX) was measured though on convention line test and the traction force was estimated by using the analytic model in skid condition. also, we have discussed the relationship between the bake force and traction force in starting condition.